English dropdown-ico

Manual Delta TP300

17 pages 1.81 mb
Download

Go to site of 17

Summary
  • Delta TP300 - page 1

    INSTRUCTION MANUAL 12" Portable Planer (Model TP300) P ART NO. 909543 - 05-01-03 Copyright © 2003 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ESP AÑOL: PÁGINA 17 ...

  • Delta TP300 - page 2

    2 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf ...

  • Delta TP300 - page 3

    3 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA TING THE MACHINE. Learning the machine’ s application, limitations, and specific hazards will gr eatly minimize the possibility of accidents and injury . 2. USE CERTIFIED SAFETY EQUIPMENT . Eye protection e ...

  • Delta TP300 - page 4

    4 ADDITIONAL SAFETY RULES FOR PLANERS F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or anothe ...

  • Delta TP300 - page 5

    5 A separate electrical circuit should be used for your machines. This cir cuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cor d is used, use only 3-wire extension cor ds which have 3- prong gr ounding type plugs and matching receptacle which will accept the machine’ s plug. Before connec ...

  • Delta TP300 - page 6

    6 Use proper extension cor ds. Make sure your extension cor d is in good condition and is a 3-wire extension cord which has a 3-pr ong grounding type plug and matching r eceptacle which will accept the machine’ s plug. When using an extension cord, be sur e to use one heavy enough to carry the current of the machine. An undersized cord will cause ...

  • Delta TP300 - page 7

    7 PLANER P AR TS 1 - 12" Planer 2 - Chip Deflector Fig. 2 Fig. 3 3 - Knife Setting Gage 4 - 8mm and 10mm Open-End Wr ench 5 - M5 x 20mm Hex Socket Head Screw 6 - M5 Wing Nut (2) 7 - M5 Flat W asher (2) 8 - Elevating Handle 1 4 7 2 8 6 5 3 ...

  • Delta TP300 - page 8

    8 ASSEMBL Y Fig. 4 Fig. 5 Fig. 6 RAISING AND LOWERING HANDLE 1. Assemble raising and lowering handle (A) Fig. 4, to shaft (B) and fasten in place with M5x20mm screw (C). NOTE: Make certain the flats of the handle and flat on shaft are aligned with each other . 2. Flip handle (A) upward as shown in Fig. 5. LOWERING EXTENSION T ABLES The infeed and o ...

  • Delta TP300 - page 9

    9 Fig. 7 Fig. 8 Fig. 9 CHIP DEFLECTOR 1. Assemble chip deflector (A) Fig. 7, to the planer by inserting end of chip deflector over the top of the cutterhead. Make certain the two screws, one of which is shown at (B) are inserted upwar d through the two slots (C) in the chip deflector . 2. Fasten chip deflector (A) Fig. 8, to planer using two M5 fla ...

  • Delta TP300 - page 10

    10 OPERA TING CONTROLS AND ADJUSTMENTS Fig. 13 Fig. 14 Fig. 15 Fig. 16 ST ARTING AND STOPPING PLANER The “ON/OFF” switch (A) Fig. 13, is located on the front of the planer motor . T o tur n the machine “ON”, move the switch toggle (B) up to the “ON” position. T o turn the switch “OFF”, move the switch toggle (B) down to the “OFF? ...

  • Delta TP300 - page 11

    11 Fig. 17 Fig. 18 Fig. 19 Fig. 20 LEVELING EXTENSION T ABLES For optimum performance, the extension tables, one of which is shown at (A) Fig. 17, must be level with the planer table. T o check the extension tables and adjust if necessary , pr oceed as follows: 1. Place a straight edge (B) Fig. 17, on the planer table (A) with one end extending out ...

  • Delta TP300 - page 12

    12 4. If an adjustment to one or both knives is necessary , slightly loosen the seven locking screws, six of which ar e shown at (C) Fig. 21, by turning the screws CLOCKWISE into the knife locking bar just enough to r elieve stress in the cutterhead and not disturb the knife setting. 5. With setting gage (B) Fig. 20, in place, apply pressur e to th ...

  • Delta TP300 - page 13

    13 Fig. 23 LIFTING STRAPS Y our planer is provided with two lifting straps (A) Fig. 23, located on the top of the planer , for ease in transporting the planer . Fig. 25 When using your machine, you may want to follow these few simple steps for achieving the best results possible. 1. T rue Up One Face – Feed one face of the board over a jointer , ...

  • Delta TP300 - page 14

    14 MAINTENANCE Fig. 26 Fig. 27 Fig. 28 Fig. 30 Fig. 29 BRUSH INSPECTION AND REPLACEMENT DISCONNECT MACHINE FROM POWER SOURCE. Brush life varies. It depends on the load on the motor . Check the brushes after the first 50 hours of use for a new machine or after a new set of brushes has been installed. After the first check, examine them after about 1 ...

  • Delta TP300 - page 15

    15 NOTES ...

  • Delta TP300 - page 16

    16 P AR TS, SERVICE OR W ARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality standards and ar e serviced by a network of Porter -Cable • Delta Factory Service Centers and Delta Authorized Service Stations. T o obtain additional information regar ding your Delta quality product or to obtain parts, service, warr ...

  • Delta TP300 - page 17

    The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas registradas de POR TER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...

Manufacturer Delta Category Planer

Documents that we receive from a manufacturer of a Delta TP300 can be divided into several groups. They are, among others:
- Delta technical drawings
- TP300 manuals
- Delta product data sheets
- information booklets
- or energy labels Delta TP300
All of them are important, but the most important information from the point of view of use of the device are in the user manual Delta TP300.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Delta TP300, service manual, brief instructions and user manuals Delta TP300. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Delta TP300.

Similar manuals

A complete manual for the device Delta TP300, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Delta TP300 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Delta TP300.

A complete Delta manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Delta TP300 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Delta TP300, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Delta TP300, that we can find in the current document
3. Tips how to use the basic functions of the device Delta TP300 - which should help us in our first steps of using Delta TP300
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Delta TP300
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Delta TP300 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Delta TP300?

Use the form below

If you did not solve your problem by using a manual Delta TP300, ask a question using the form below. If a user had a similar problem with Delta TP300 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)