English dropdown-ico

Manual Tripp Lite SU10K

17 pages 0.51 mb
Download

Go to site of 17

Summary
  • Tripp Lite SU10K - page 1

    1 Copyright © 2001 Tripp Lite. All rights reserved. SmartOnline TM is a registered trademark of Tripp Lite. 1111 W. 35th Street Chicago, IL 60609 USA Customer Support: (773) 869-1234 Application Services: (773) 869-1236 www.tripplite.com Owner's Manual Smar tOnline TM • SU6K (6kV A) • SU10K (10kV A) On-Line, Extended-Run UPS Systems ESP A ...

  • Tripp Lite SU10K - page 2

    2 Safety This manual contains important instructions and warnings that should be followed during the installation, operation and storage of all Tripp Lite SmartOnline UPS Systems. UPS Location W arnings • Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight. • Install your UPS in a structurally sound area. Your U ...

  • Tripp Lite SU10K - page 3

    3 Contr ol P anels Familiarize yourself with the location and function of the front and rear panel features before installing and operating your UPS. 1. “ON/OFF” Switch: This momentary rocker switch turns the UPS System’s inverter ON and OFF. 2. “SELECT” Button: This button performs two functions: it allows you to browse through different ...

  • Tripp Lite SU10K - page 4

    4 SU10KPM SU6K SUBP SU10KBP Rear P anels ON LINE MODE ECONOMY MODE ON LINE MODE ECONOMY MODE 1 14 3 6 10 11 2 4 5 8 7 9 16 15 18 13 5 12 17 1 14 3 6 10 11 2 4 5 8 7 9 16 15 18 13 17 12 2 5 12 5 L1 L2 ...

  • Tripp Lite SU10K - page 5

    5 1. Manual Bypass Switch: This red and yellow dial is used in one step of putting the UPS in "BYPASS” mode, which must be done before performing any maintenance on the UPS with the connected load supported. (See page 12 for step-by-step instructions for going into "BYPASS.") While this switch is on "BYPASS," connected eq ...

  • Tripp Lite SU10K - page 6

    6 INVERTER OPERA TION DIP SWITCH SETTINGS (SU10KPM SHO WN) Using a small tool, set the four Inverter Opera- tion DIP Switches (located on the rear panel of your UPS, see pg. 4-5 for location) to match your input voltage, input frequency and desired operational mode. Input V oltage Selection (DIP Switches #1 & #2) (Input V oltage Select Ter mina ...

  • Tripp Lite SU10K - page 7

    7 UPS LOCA TION Move your UPS over short distances using its wheels. Stabilize the UPS by releasing the stabilizers on each side of the unit. NOTE: Do not stack the UPS Systems or external battery packs. INPUT AND OUTPUT CONNECTION WIRING SELECTION Choose appropriate cabling (depending on current carried; see chart below) to connect your UPS to an ...

  • Tripp Lite SU10K - page 8

    8 EXTERNAL B A TTER Y P A CK CONNECTION (SU6K: Optional; SU10K: Required) Since SU6K models contain internal batteries, connecting external battery packs (to extend runtime) is optional. SU10KPM models, however, do not have internal batteries and require an external battery pack connection to a SU10KBP or a SUBP. Using the supplied battery connecti ...

  • Tripp Lite SU10K - page 9

    9 B A TTER Y CONDITION VERIFICA TION When the UPS is operating from battery power, the alarm and LCD Display will both alert you to the UPS battery’s charge condition. Battery Charge Condition Alarm LCD Display FULL Short Beep (every 2 seconds) ON BATTERY BATT = XXV XX% LOW Short Beep (every 1/2 second) BATTERY LOW BATT = XXV XX% UNDER Continuous ...

  • Tripp Lite SU10K - page 10

    10 SELF-TESTING When you turn the UPS ON, it will perform a brief (about 25 second) self-test. See figure below for display sequence.* *Note: If starting from battery, the BATTERY LED will be lit and the I/P and BYPASS LEDs will not. The final LCD display in the diagram below appears when the UPS is operating normally under utility-supplied AC inpu ...

  • Tripp Lite SU10K - page 11

    11 Operation (Special Conditions) OPERA TION ON BYP ASS—V OL T A GE OUT OF RANGE While in Bypass Mode, the UPS monitors the input voltage, which on Bypass equals the output voltage. If the output voltage passes out of an acceptable range (between 15% higher and 20% lower than nominal), the UPS displays the condition on its LCD and stops supplying ...

  • Tripp Lite SU10K - page 12

    12 OPERA TION UNDER SHUTDO WN Your UPS will shut down and the LCD will display a message if it detects one of the following conditions. Note: For all conditions, the “Input,” “Output” and “Bypass” LEDs will be illuminated. Condition LCD Display Message Extended Overload (>150%) OVERLOAD 150% SHUT DOWN Output Short Circuit SHORT CIRCU ...

  • Tripp Lite SU10K - page 13

    13 RS-232 INTERF A CE This female DB9 port connects your UPS via an RS-232 cable to a workstation or server equipped with Tripp Lite software. The port uses RS-232 communications to report UPS status and power conditions. Using this port, Tripp Lite software can monitor and manage network power and automatically save open files and shut down equipm ...

  • Tripp Lite SU10K - page 14

    14 DR Y CONT A CT INTERF A CE: This female DB9 contact-closure port allows your UPS to send contact-closure signals to indicate that it is on battery back-up mode and if its batteries are running low. The port can also receive a remote shutdown signal. Pin assignment: DR Y CONT ACT INTERF ACE T ABLE UPS Operating Pin 8,3 Pin 1,3 Mode Normal OPEN OP ...

  • Tripp Lite SU10K - page 15

    15 Ser vice Service Your SmartOnline UPS is covered by the 2-year limited warranty period described below. A variety of service contracts is also available from Tripp Lite, including start- up service contracts and 3- to 5-year SafeSure on-site service contracts. For more infor mation, call T ripp Lite Customer Service at (773) 869-1233. W arranty ...

  • Tripp Lite SU10K - page 16

    16 F unction Block Diagram LEDS LCD TO RS-232 AS-400 DRY CONTACT ACCESSORY SLOT REPO AC INPUT BREAKER AC INPUT SURGE PROTECTOR INPUT FIL TER AC TO DC CONVERTER DC TO AC INVERTER STA TIC BYPA S S SWITCH OUTPUT FIL TER MANUAL BYPA S S SWITCH OUTPUT ISOLATION XFM OUTPUT BREAKER OUTPUT TERMINAL BLOCK STANDARD BATTERIES: 240 VDC SUBP EXTERNAL BATTERY CA ...

  • Tripp Lite SU10K - page 17

    17 Specifications (Note: Excluding isolation transformer) Model SU6K SU10K Input Input Voltage 156V~280V Single Phase 156V~280V Single Phase Input Frequency 50/60 Hz ± 3 Hz 50/60 Hz ± 3 Hz (selectable, pg. 7) (selectable, pg. 7) Input Current 32A 50A Inrush Current <150A <200A Power Factor (Full Load) >0.99 >0.99 Efficiency (Full Load ...

Manufacturer Tripp Lite Category Power Supply

Documents that we receive from a manufacturer of a Tripp Lite SU10K can be divided into several groups. They are, among others:
- Tripp Lite technical drawings
- SU10K manuals
- Tripp Lite product data sheets
- information booklets
- or energy labels Tripp Lite SU10K
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tripp Lite SU10K.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tripp Lite SU10K, service manual, brief instructions and user manuals Tripp Lite SU10K. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tripp Lite SU10K.

Similar manuals

A complete manual for the device Tripp Lite SU10K, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tripp Lite SU10K by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tripp Lite SU10K.

A complete Tripp Lite manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tripp Lite SU10K - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tripp Lite SU10K, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tripp Lite SU10K, that we can find in the current document
3. Tips how to use the basic functions of the device Tripp Lite SU10K - which should help us in our first steps of using Tripp Lite SU10K
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tripp Lite SU10K
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tripp Lite SU10K in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tripp Lite SU10K?

Use the form below

If you did not solve your problem by using a manual Tripp Lite SU10K, ask a question using the form below. If a user had a similar problem with Tripp Lite SU10K it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)