English dropdown-ico

Manual TANDBERG D1320202

32 pages 0.34 mb
Download

Go to site of 32

Summary
  • TANDBERG D1320202 - page 1

    TANDBERG GW Data port Comm and Interfac e User G uide 1 T ANDBERG 3G GW Data port Command Interface User Guide Softwar e version R2 D1320202 TANDBERG ...

  • TANDBERG D1320202 - page 2

    TANDBERG GW Data port Comm and Interfac e User G uide 2 Table of Contents 1. INTRODUCTION ................................................................................................................... ........ 3 2. CONNECTIN G TO THE DATA PORT C OMMAND INTERFACE THROUGH T HE RS- 232 PORT. ....................................................... ...

  • TANDBERG D1320202 - page 3

    TANDBERG GW Data port Comm and Interfac e User G uide 3 1. Introduction The TANDBERG GW Data port Command Interface User Guide contains guidelines on how to use the textual command interface supported by the GW. The Data port Command Interface can be accessed through Telnet via the LAN interface or through RS-232 by connecting a serial cable to the ...

  • TANDBERG D1320202 - page 4

    TANDBERG GW Data port Comm and Interfac e User G uide 4 2. Connecting to the Data port Command Interface through the RS-232 port. The RS-232 port is a 9-pin, fem ale, D-sub connector located on the front of the GW. The port is configured as a DCE (Data Communications Equipment). The RS-232 port is default set to 115200 baud, 8 data bits, none parit ...

  • TANDBERG D1320202 - page 5

    TANDBERG GW Data port Comm and Interfac e User G uide 5 2.2. Troubleshooting If communication cannot be established between the PC/terminal and the TANDBERG GW’s Data port the following should be checked: • Verify that the serial cable is a straight through 9-pin to 9-pin cable • Confirm that the configuration of the PC/terminal’s serial RS ...

  • TANDBERG D1320202 - page 6

    TANDBERG GW Data port Comm and Interfac e User G uide 6 3. Connecting to the Data port Co mmand Interface using Telnet The TANDBERG 3GW has one LAN port. The GW’s Telnet server provides access to the Data port Command Interface through a 10/100 base T network interface supporting the TCP/ IP protocol. When connected to the 3G Gateway, type ts h t ...

  • TANDBERG D1320202 - page 7

    TANDBERG GW Data port Comm and Interfac e User G uide 7 4. The TANDBERG 3G Gateway Commands 4.1. Introduction Typing ‘ ? ’ or ‘ help ’ when connected to the Data Port Command Interface will return a list of valid commands. The commands are used to control the functions of the 3G Gateway. A command may be followed by a set of parameters and ...

  • TANDBERG D1320202 - page 8

    TANDBERG GW Data port Comm and Interfac e User G uide 8 • User Commands, Xcom. Parameter Configuration Commands are commands that set a system parameter to a specific value. E.g.: The command Xconf telnet mode: "on" enables telnet access on the gateway. If the command is syntactically correct the GW returns OK , otherwise the GW returns ...

  • TANDBERG D1320202 - page 9

    TANDBERG GW Data port Comm and Interfac e User G uide 9 4.2.1. System Configuration Commands Command: Description: H323Gatekeeper Sets gatekeeper parameters. NOTE! H.323 services must be set before t he GW can be registered t o a gatekeeper. H323Gatekeeper Address <IPAddr> or H323Gatekeeper Authe ntication Mode <Auto/off> or H323Gatekee ...

  • TANDBERG D1320202 - page 10

    TANDBERG GW Data port Comm and Interfac e User G uide 10 • DNS Server: Num ber identify ing one of 5 DNS serve rs which can be configured. If this parameter is omitted th e command applies to the first configuratio n (1). sub-co mmands: • Assignment : Selects between DHCP (Dynamic Host Configuratio n Protocol) or static IP address allocation. W ...

  • TANDBERG D1320202 - page 11

    TANDBERG GW Data port Comm and Interfac e User G uide 11 Within ISDN different bearer cap abilities are used to signal the type of d ate (Voice, Data, H32 0, H324M), whic h is used by switches and other equipment to determine what to do with the data or the call (compand neglect etc). • IncomingBearerCapability : sets the ISDN bearer capability o ...

  • TANDBERG D1320202 - page 12

    TANDBERG GW Data port Comm and Interfac e User G uide 12 SNMP SystemLoca tion: <S: 0, 70> or SNMP HostIPAddr [1..3]: < IPAddr> --- parameters: • Mode: < On/Off/ReadOnly/TrapsOnly > • Community Name: Text st ring of m aximum 16 characters. • System Contact: Text strin g of ma ximum 70 c haracters • System Location: Text str ...

  • TANDBERG D1320202 - page 13

    TANDBERG GW Data port Comm and Interfac e User G uide 13 sub-co mmands • Name, sets the name of the 3G Gateway • Password, sets the password of the 3G gateway Example of SystemUnit fee dback: *c xConfigurat ion System Unit Name: "" ...

  • TANDBERG D1320202 - page 14

    TANDBERG GW Data port Comm and Interfac e User G uide 14 4.2.2. General GW Commands Command: Description: Gateway This command is used to co nfigure th e 3G gateway dialling rules, like for example direct inward dialli ng, H323 call prefixes and di al in numbers. It is possible to de fine 100 services, each wi th the param eters: • Description in ...

  • TANDBERG D1320202 - page 15

    TANDBERG GW Data port Comm and Interfac e User G uide 15 Example of Gateway feedback: *c xConfigurat ion Gateway Servi ce 1 Description: "" *c xConfigurat ion Gateway Service 1 Servic eType: DiD *c xConfigur ation Gateway Se rvice 1 InNetType: H3 24m/3G *c xConfigurat ion Gateway Servi ce 1 InPrefix: 6789 "" *c xConfigurat ion G ...

  • TANDBERG D1320202 - page 16

    TANDBERG GW Data port Comm and Interfac e User G uide 16 NOTE! The GW needs to reboot before the chang es will take effect . Options [1 . . 64] Key: < S: 0, 90> --- sub-co mmands: • Key : Option key for e.g. BRI, PRI or SS7 trunk s. Example of Options feedback: *c xConfigur ation Opti ons 1 Key: "11520 1SS7-1-55C 3EBB7" *c xConfig ...

  • TANDBERG D1320202 - page 17

    TANDBERG GW Data port Comm and Interfac e User G uide 17 LinkSet [1 .. 2] Link [1 . . 2] Timeslot: <1 .. 31> LinkSet [1 .. 2] Link [1 . . 2] SLC: <0 .. 15> Trunk [1 .. 4] Mode: <On/Off> Trunk [1 .. 4] DPC: <0 .. 16383> Trunk [1 .. 4] CircuitIdentificationCode: <0 .. 16383> Route [1 .. 8] DPC: <0 .. 16383> Route [ ...

  • TANDBERG D1320202 - page 18

    TANDBERG GW Data port Comm and Interfac e User G uide 18 in the 3G Gateway User Manual. Example of SS7 feedback: *c xConfig uration S S7 OPC: 0 *c xConfigur ation SS7 NetworkIn dicator: N ational0 *c xConfigur ation SS7 Law: ALaw *c xConfig uration S S7 LinkSe t 1 Mode: Off *c xConfig uration S S7 LinkSe t 1 DPC: 0 *c xConfig uration S S7 LinkSe t ...

  • TANDBERG D1320202 - page 19

    TANDBERG GW Data port Comm and Interfac e User G uide 19 *c xConfigur ation SS7 Trunk 3 M ode: Off *c xConfigur ation SS7 Trunk 3 DPC : 0 *c xConfiguration SS7 Trunk 3 CircuitIdentification Code: 0 *c xConfigur ation SS7 Trunk 4 M ode: Off *c xConfigur ation SS7 Trunk 4 DPC : 0 *c xConfiguration SS7 Trunk 4 CircuitIdentification Code: 0 *c xConfigu ...

  • TANDBERG D1320202 - page 20

    TANDBERG GW Data port Comm and Interfac e User G uide 20 VideoPortal Registers the 3G Gateway with the VideoPortal NOTE! The GW needs to reboot before the chang es will take effect . Mode <On/Off> or System [1 .. 2] IP Address < IPAddr> --- sub-co mmands: • Mode : If Mode = On the 3G Gateway is registered with 1 or 2 video portals • ...

  • TANDBERG D1320202 - page 21

    TANDBERG GW Data port Comm and Interfac e User G uide 21 4.2.3. System Status Commands Command: Description: SystemUnit Displays information reg arding the physical system SystemUnit Status format: <ProductType> <Uptime> <Software Version> Name> ReleaseDate> Configuration Telephony:> VideoTelephony:> <Hardware : Ver ...

  • TANDBERG D1320202 - page 22

    TANDBERG GW Data port Comm and Interfac e User G uide 22 Telephony: 0 VideoTelephony: 0 Hardware: Version: "3GW 1.0" SerialNumber: "43A00001" MainBoar d: "" AdditionalBoard: "" Configur ation: PRI:41 Temperat ureCelcius: NA Temperat ureFahrenheit: NA *s/end Ethernet Displays the configuration of the Et hernet ...

  • TANDBERG D1320202 - page 23

    TANDBERG GW Data port Comm and Interfac e User G uide 23 • DNS Server [1.. 5] Addr ess , th e IP numb er s o f ma xi mu m 5 D NS servers • Domain , the name of the domain the gateway is part of. Example of IP feedback: * s IP: Address: "10.31.0.5" SubnetMask: "255.25 5.248.0" Gateway: "10.31.0 .1" DNS: Server 1: Ad ...

  • TANDBERG D1320202 - page 24

    TANDBERG GW Data port Comm and Interfac e User G uide 24 Example of Ex ternalManage r feedback: * s ExternalMana ger: Address: "" Protoc ol: HTTP URL: "t ms/public/ external/mana gement/SystemM anagement Service.asmx " *s/end BRI [1..4] Displays the status of the BRI lines BRI Parameters: • BRI [1..4] i ndicating t he status o ...

  • TANDBERG D1320202 - page 25

    TANDBERG GW Data port Comm and Interfac e User G uide 25 Channel 15 (type=BChannel, status =Idle): / Channel 16 (type=DChannel, status=NA): / Channel 17 (type=BChannel, status =Idle): / Channel 18 (type=BChannel, status =Idle): / Channel 19 (type=BChannel, status =Idle): / Channel 20 (type=BChannel, status =Idle): / Channel 21 (type=BChannel, statu ...

  • TANDBERG D1320202 - page 26

    TANDBERG GW Data port Comm and Interfac e User G uide 26 Example of GatewayCa ll feedback: *s GatewayCall 1 (status=Inactive): / *s/end OK *s GatewayCall 1 (status=Active): CallRef 1: 1 CallRef 2: 2 *s/end OK xstat gatewaycall 1 *s GatewayCall 1 (status=Active): CallRef 1: 1 CallRef 2: 3 *s/end OK SystemLoad Returns the current system load in perce ...

  • TANDBERG D1320202 - page 27

    TANDBERG GW Data port Comm and Interfac e User G uide 27 LastCorrect ion: 1 *s/end 4.2.4. Debug Commands Command: Desription : Syslog Enables a real- time log o f Bonding , H.221 a nd H.323, H 324m, ISDN, R TSP, IVi der, SIP and IVi der Engine acti vity. Note! Logging via the serial port is limited by the speed of the serial port, which might resul ...

  • TANDBERG D1320202 - page 28

    TANDBERG GW Data port Comm and Interfac e User G uide 28 feedback to 3 differe nt URLs. The sy stem allows a total of 20 XPath expressions to be registered, with a m aximum of 1 5 for a single URL. Parameters: • ID: <1 .. 3> ID for the registration. If this parameter is omitted the system uses the first vacant ID. • URL(r): <S: 0, 256& ...

  • TANDBERG D1320202 - page 29

    TANDBERG GW Data port Comm and Interfac e User G uide 29 Example: Xcomma nd OptionKey Add 1152 01P1-1-6A 96DAA4 *r Result (status=OK): / *r/end OK OptionKeyDel ete Command used to delete option keys. Parameters: • Key(r): <S: 0, 90> opti on key Example (Delete Option Key nr . 1): xComm and OptionKey Delete 1 *r Result (status=OK): / *r/end ...

  • TANDBERG D1320202 - page 30

    TANDBERG GW Data port Comm and Interfac e User G uide 30 or: xfeedback list - (note: deregistration with index=0 will deregister all registered expressions) Examples : "xfeedback register status/ca ll" - t o monitor call changes "xfeedback register status/call--" - to monitor only call state changes "xfeedback register conf ...

  • TANDBERG D1320202 - page 31

    TANDBERG GW Data port Comm and Interfac e User G uide 31 ...

  • TANDBERG D1320202 - page 32

    TANDBERG GW Data port Comm and Interfac e User G uide 32 4.3. Index Commands boot, 27 BRI [1..4], 24 Call [1..90], 26 DefaultValuesSet, 27 E1, 11 Ethernet, 10 , 22 externalManager, 15 ExternalMana ger, 23 Feedback [1 3], 25 FeedbackDeregister, 28 FeedbackRegister, 27 , 29 Gateway, 14 GatewayCall [1..30], 25 H323CallSetup, 9 h323gatekeepe r, 9 H323G ...

Manufacturer TANDBERG Category Network Router

Documents that we receive from a manufacturer of a TANDBERG D1320202 can be divided into several groups. They are, among others:
- TANDBERG technical drawings
- D1320202 manuals
- TANDBERG product data sheets
- information booklets
- or energy labels TANDBERG D1320202
All of them are important, but the most important information from the point of view of use of the device are in the user manual TANDBERG D1320202.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals TANDBERG D1320202, service manual, brief instructions and user manuals TANDBERG D1320202. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product TANDBERG D1320202.

Similar manuals

A complete manual for the device TANDBERG D1320202, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use TANDBERG D1320202 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of TANDBERG D1320202.

A complete TANDBERG manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual TANDBERG D1320202 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the TANDBERG D1320202, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the TANDBERG D1320202, that we can find in the current document
3. Tips how to use the basic functions of the device TANDBERG D1320202 - which should help us in our first steps of using TANDBERG D1320202
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with TANDBERG D1320202
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of TANDBERG D1320202 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning TANDBERG D1320202?

Use the form below

If you did not solve your problem by using a manual TANDBERG D1320202, ask a question using the form below. If a user had a similar problem with TANDBERG D1320202 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)