English dropdown-ico

Manual Kicker SX900.4

20 pages 1.86 mb
Download

Go to site of 20

Summary
  • Kicker SX900.4 - page 1

    ...

  • Kicker SX900.4 - page 2

    3 SX .4 Series Amplifiers F ea tures F ea tures Low Impedance Operation Stable into 2 ohm stereo or 4 ohm mono loads. SORT Protection Circuitry ( S hort circuit, O ver -voltage, R everse polarity , T hermal) Protects amplifier from accidents and out of spec operation. MOSFET Power Supply Pr ovides high ef ficiency operation. PAST ( P re A mp S igna ...

  • Kicker SX900.4 - page 3

    5 SX .4 Series Amplifiers F ea tures VFD DISPLAY - cont GAIN - Indicates you are in the gain menu. EQ - Indicates you are in the equalizer menu. LPF - Indicates you are in the low pass filter menu. HPF - Indicates you are in the high pass filter menu. PHASE - Indicates you are in the phase menu. KOMP - Indicates you are in the Kompressor menu. MEM- ...

  • Kicker SX900.4 - page 4

    7 SX .4 Series Amplifiers Installa tion Moun ting When selecting a location to mount your Kicker amplifier be sure it is structurally sound and that ther e are no items behind the area that could be damaged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc. All amplifiers generate heat under normal operation. Be sure to choos ...

  • Kicker SX900.4 - page 5

    9 SX .4 Series Amplifiers Installa tion S yst em Diagrams FOUR CHANNEL OPERATION (STEREO) SX.4 series amplifiers are capable of operating into a minimum impedance of 2 ohms per channel in stereo operation. R M1 M2 M3 M4 ESC ENT HOME SYS MEM-1 GAIN EQ LPF HPF KOMP AMP1 LOCK MEM-2 MEM-3 MEM-4 PHASE MUTE AMP2 LEFT RIGHT ** kicker L+ L - R+ R - RIGHT S ...

  • Kicker SX900.4 - page 6

    11 SX .4 Series Amplifiers Installa tion USING THE SIGNAL OUTPUT JACKS (PAST) The Output ( P re A mp S ignal T ransfer) RCA jacks allow you to send the incoming signal from the AMP 1 RCA input jacks on one Kicker SX.4 series amplifier to another amplifier or proces- sor without the need for Y cables. The signal from the PAST jacks is identical to t ...

  • Kicker SX900.4 - page 7

    13 SX .4 Series Amplifiers Opera tion Na viga tion Y our KICKER SX series amplifier uses the latest in Digital DSP control and provides you with valuable operational infor ma- tion about your amplifier , real-time diagnostics and a full multi-level menu-driven operating system to access and adjust your amplifier . The menu system is designed in lay ...

  • Kicker SX900.4 - page 8

    15 SX .4 Series Amplifiers Opera tion Menu S yst em The menu system layout is as follows: DEFAULT - This menu is displayed when your amp is operating and no adjustments are being made to your ampli- fier . This information scrolls through the display one after the other and then repeats. 1.) KICKER - Hey , we needed a brand plug for us since this a ...

  • Kicker SX900.4 - page 9

    17 SX .4 Series Amplifiers Opera tion SICK BAY - cont 7c.) PINK NOISE is a built in pink noise generator to test operation of the amplifier Use the UP and DOWN keys to select NOISE ON or NOISE OFf . When the PINK NOISE is ON the LEFT and RIGHT indicators in the ISIS VFD will blink on and of f. When you are done using the PINK NOISE generator press ...

  • Kicker SX900.4 - page 10

    19 SX .4 Series Amplifiers Opera tion 14.) Komp Adj. - This adjusts the KOMPRESSOR activation threshold point. Range is +24 dB to -24 dB to allow for dif ferent sized speakers or listener tastes. 0 is the default factory setting. There are two KOMP ADJ. menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual se ...

  • Kicker SX900.4 - page 11

    21 SX .4 Series Amplifiers Opera tion 18.) About - This menu item will display information about the DAP (Digital Audio Processor) hardwar e, software and build date. Use the UP and DOWN keys to view the DSP V ersion, Software V ersion, Hardware V ersion and Build Date. Press the ESC key to r eturn to the MAIN menu. Gain MENU - This menu is where y ...

  • Kicker SX900.4 - page 12

    23 SX .4 Series Amplifiers Opera tion Lo-Pass MENU - This menu is where you adjust the low pass crossover for each amplifier . There are two LO-P ASS menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual LO-P ASS setting. Use the UP and DOWN keys to scroll through AMP-1 and AMP-2 and press the ENT key to sele ...

  • Kicker SX900.4 - page 13

    25 SX .4 Series Amplifiers Opera tion Phase MENU - Here you can switch the polarity of each amplifier’ s channel(s) output between 0 or 180 degrees. There are two PHASE menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual PHASE setting. Use the UP and DOWN keys to scroll through AMP-1 and AMP-2 and press t ...

  • Kicker SX900.4 - page 14

    27 SX .4 Series Amplifiers Opera tion Kompressor MENU - Here you can select each amplifier’ s Kompressor setting you wish to use. The SX amplifier utilizes a full digital compressor circuit to tweak the amplifier and the sound to your unique needs. There are two KOMPRESSOR menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have ...

  • Kicker SX900.4 - page 15

    29 SX .4 Series Amplifiers Opera tion UNLOCK AMPLIFIER - cont. If you enter the wrong code the display will flash the mes- sage BAD CODE and return you to the UNLOCK screen. Press the ENT key to enter your lock your code again. Enter your code again making sure to place the corr ect character in the correct position in the display . Blank spaces co ...

  • Kicker SX900.4 - page 16

    31 SX .4 Series Amplifiers Opera tion PRESET PRESETS Ok, we know that sounds like a certain pizza commercial, but seriously the four memory presets come with settings already in them. Y ou can use these as a starting point to do your own tweaking or for quick push-a-button-and-be-done setup. Any preset you store will r eplace the ones that come fro ...

  • Kicker SX900.4 - page 17

    33 SX .4 Series Amplifiers Help  Alternator n n oise (whining sound that varies with engine RPM) : ¬ Check for damaged RCA cables. ¬ Check routing of RCA cable. ¬ Check source unit for good ground. ¬ Check GAIN RANGE in SYSTEM menu, turn down if set too high. ¬ Check GAIN in MAIN MENU, turn down if set too high. CAUTION: When jump-starting ...

  • Kicker SX900.4 - page 18

    35 SX .4 Series Amplifiers Specifica tions P erf ormanc e Model SX700.4 SX900.4 RMS Power In Watts, All Channels Driven @ 13.8V, 4 Ω Stereo, 0.02% THD 82 x 4 107 x 4 @ 13.8V, 2 Ω Stereo, 0.2% THD 163 x 4 213 x 4 @ 13.8V, 4 Ω Mono, 0.4% THD 325 x 2 425 x 2 Dynamic Power In Watts, All Channels Driven @ 14.4V, 4 Ω Stereo, 1% THD 85 x 4 115 x 4 ...

  • Kicker SX900.4 - page 19

    37 SX .4 Series Amplifiers Warran ty EL E CTRONICS LIMIT ED WARRAN TY WHA T IS NO T C O V ERED? Kicker warrants this product to be free fr om defects in material and workman- ship under normal use for a period of 90 DAYS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer it is war ranted for TWO (2) YEARS f ...

  • Kicker SX900.4 - page 20

    39 SX .4 Series Amplifiers No t es Chic’s Numbers Hook Ups 38 SX .4 Series Amplifiers No t es No t es Pizza Deliv ery ...

Manufacturer Kicker Category Stereo Amplifier

Documents that we receive from a manufacturer of a Kicker SX900.4 can be divided into several groups. They are, among others:
- Kicker technical drawings
- SX900.4 manuals
- Kicker product data sheets
- information booklets
- or energy labels Kicker SX900.4
All of them are important, but the most important information from the point of view of use of the device are in the user manual Kicker SX900.4.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Kicker SX900.4, service manual, brief instructions and user manuals Kicker SX900.4. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Kicker SX900.4.

Similar manuals

A complete manual for the device Kicker SX900.4, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Kicker SX900.4 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Kicker SX900.4.

A complete Kicker manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Kicker SX900.4 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Kicker SX900.4, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Kicker SX900.4, that we can find in the current document
3. Tips how to use the basic functions of the device Kicker SX900.4 - which should help us in our first steps of using Kicker SX900.4
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Kicker SX900.4
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Kicker SX900.4 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Kicker SX900.4?

Use the form below

If you did not solve your problem by using a manual Kicker SX900.4, ask a question using the form below. If a user had a similar problem with Kicker SX900.4 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)