English dropdown-ico

Manual Heath Zenith Lighted Wireless Push Button Accessory

24 pages 0.12 mb
Download

Go to site of 24

Summary
  • Heath Zenith Lighted Wireless Push Button Accessory - page 1

    Lighted Wireless Push Button Accessory The Heath ® /Zenith Wireless Push Button Accessory works with existing Heath ® /Zenith jumper or dip switch systems . • Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house. • LED lighted push bar (see Lighted Push Bar Feature ). © 20 ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 2

    -2- 598-1137-02 1. Install two lithium type CR2032 3 volt bat- teries (included). Remov e back of case by pushing in tab on bottom with a small screw- driver . Make sure batter y is oriented properly (see page 5). 2. Set the push button jumpers to match the chime receiver code. See “Code and T une Setting” section. 3. T est r ang e . T empor ar ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 3

    -3- 598-1137-02 Code and T une Settings Code Settings Note: Most installations will not require you to change any jumpers on y our chime and push b utton. W ARNING: Disconnect chime unit from power source before opening code access door . Close door and replace screw before reconnecting to po wer . The push button and chime communicate by using a c ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 4

    -4- 598-1137-02 T une Settings Y our Heath ® /Zenith wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note) , or Wes tminste r (eight note) (A v ailab le on selected Heath ® /Zenith chimes). The f actor y setting is for the Ding- Dong tune (or Westminster , when av ailable). This tune can be changed by f ollowing the ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 5

    -5- 598-1137-02 C R 2 0 3 2 + 1 2 3 4 5 6 7 8 12345678 Inside Push Button Replacing Push Button Batteries Ins tall tw o lith ium type CR203 2 3 vol t batter ies . Inser t Batteries (+) Positiv e Side Up. * Code Settings 1-7 Must Match Both Push Button and Chime Remov e screw to open access door T une Setting (Not used on all models) Back of Chime T ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 6

    -6- 598-1137-02 T roubleshooting Chime does not sound: • Make sure push b utton and chime codes are the same (See pages 3, 4, and 5). • Check orientation of push button battery (See page 5). • Chec k charge of push but ton and chime batte ries (if appl icab le) , repl ace if necessary . Batteries seem OK, but the chime does not w ork when ins ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 7

    -7- 598-1137-02 Regulatory Information This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Oper ation is subject to the f ollowing two conditions: (1) this de vice ma y not cause har mful interf erence, and (2) this de vice must accept any interference receiv ed, including interference that ma y cause undesired operat ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 8

    -8- 598-1137-02 FIVE YEAR LIMITED W ARRANTY This is a “Li mited Warr anty” whic h giv es you specific lega l rig hts. You may also have othe r rig hts wh ich v ary f rom s tate to st ate o r prov ince to pr ovinc e. For a peri od of five years from the date of purchas e, any malfu nctio n caused by fact ory d efect ive pa rts o r wor kmans hi ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 9

    -9- 598-1137-02 Accesorio de pulsador inalámbrico El accesor io de pulsador inalámbr ico Heath ® /Zenith funciona con el puente Heath ® /Zenith o con los sistemas de interruptores. • Pulsador alimentado con pila – No se necesitan alambres. • Los 128 códigos elegibles per miten más de un sistema de campanas en la misma casa. • Barra de ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 10

    -10- 598-1137-02 1. Instale las dos baterías(pilas) de litio tipo CR2032 de 3 voltios del pulsador (inclui- das). Extraer la par te posterior de la caja presi onando la aleta en el botón con un destor- nillador pequeño. Asegurarse que la pila esté orientada correctamente (ver la página 13). 2. Fije los puentes del pulsador de acuerdo al códig ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 11

    -11- 598-1137-02 Programaciones del código y del tono Programaciones del código Nota: En la ma y oría de instalaciones no será necesario que cambie ningún puente en su campana o en su pulsador . AD VERTENCIA: Desconecte la unidad de la campana de la fuente de alimentación antes de abrir la puerta de acceso de códigos. Cierre la puer ta y pon ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 12

    -12- 598-1137-02 Programación del tono Su cam pan a ina lám bri ca Hea th ® /Zenith tiene tonos dif eren tes que pueden seleccionarse: Tilín (una nota), Tilín-T alán (dos notas), o W estminster (ocho notas) (Disponible en los timbres Heath ® /Zenith seleccionados). La calibración de fábr ica es el tono Tilín-talán (o el tono Westminster ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 13

    -13- 598-1137-02 C R 2 0 3 2 + 1 2 3 4 5 6 7 8 12345678 Dentro del Pulsador Reemplazo de las baterías del pulsador Ins tale dos bate rías (pil as) de lit io tipo CR20 32 de 3 voltios. Coloque las baterías con el lado positivo (+) hacia arriba * Las Calibraciones de Código del 1-7 Deben Coincidir T anto en el Pulsador Como en el Timbre Quite el ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 14

    -14- 598-1137-02 Análisis de A verías La campana no suena: • Asegúrese que los códigos del pulsador y de la campana sean los mismos (V ea las páginaciones 11, 12 y 13). • V erifique la posición de la batería del pulsador (V er página 13). • Revise la carga de las baterías del pulsador y de la campana (si es aplicable), reemplácelas ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 15

    -15- 598-1137-02 Servicio Técnico Fa vor de llamar al 1-800-858-8501 (sólo para hab lar en inglés) para pedir ayuda antes de de volver el pr oducto a la tienda. Si tiene algún problema, siga esta guía. Usted puede también visitar nuestro sitio Web: www .hzsupport.com. Si el prob lema continúa, llame al 1-800-858-8501 (sólo para hablar en in ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 16

    -16- 598-1137-02 GARANTÍA LIMIT ADA A 5 AÑOS Esta es una “Garantía Limitada” que le da a Ud. derechos legales específicos. Usted puede también tener otros derechos que varían de estado a estado o de provincia a provincia. P or un período de 5 años desde la fecha de compra, cualquier mal funcionamiento ocasionado por partes defectuosas ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 17

    -17- 598-1137-02 L ’acc esso ire de bout on-p ouss oir sans fil Heat h ® /Ze nith fo ncti onne av ec les systèmes à cav alier ou à commutateurs DIP Heath ® /Zenith e xistants. • Bouton-poussoir alimenté par pile - aucun fil à acheminer . • Choix de 128 codes à sélectionner , pouv ant admettre plus qu’un seul système de carillon ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 18

    -18- 598-1137-02 1. Installez les deux (2) piles au lithium de 3 V , de type CR2032, pour bouton-poussoir (comprises). Ôtez la par tie arrière du boîtier en enfonçant la patte du bas au moyen d’un petit tour nevis. Assurez-vous que la pile est orientée correctement (voir p . 21). 2. Réglez les cavalier s du bouton-poussoir de manière à co ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 19

    -19- 598-1137-02 Réglages du code et de la mélodie Réglage du code Rem ar que : A vec la plup art des insta llat ions , vou s n’av ez pas à changer aucun cavalier sur votre carillon ou votre unité de bouton-poussoir . A VERTISSEMENT : Débrancher le carillon de la source d’ali- mentation avant d’ouvrir la porte d’accès au code. Referm ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 20

    -20- 598-1137-02 Réglage de la mélodie V otre carillon sans fil Heath ® /Zenith peut jouer différents airs à sélec- tionner : Ding (une note), Ding-Dong (deux notes) et W estminster (huit notes) (Disponible sur cer tains modèles de carillon Heath ® /Zenith). Le réglage de l’usine est celui du timbre Ding-Dong (ou l’air Westminster , l ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 21

    -21- 598-1137-02 C R 2 0 3 2 + 1 2 3 4 5 6 7 8 12345678 Unité de bouton-poussoir intérieure Remplacement des piles de l'unité de bouton-poussoir Installez les deux (2) piles au lithium de 3 V , de type CR2032. Insérez les piles, borne positive (+) v ers le haut. * Les réglages de code 1-7 doivent correspondre à l’unité de bouton-pouss ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 22

    -22- 598-1137-02 Dépannage Le carillon ne sonne pas: • Assur ez-v ous que les codes de l’unité de bouton- pousso ir et du carillo n sont identiques (V oir les pages 19, 20 et 21). • Vérifiez l’orientation de la pile de l’unité de bouton-poussoir (V oir page 21). • Vérifiez l’état de charge des piles de l’unité de bouton-pou ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 23

    -23- 598-1137-02 Service T echnique V euillez faire le 1 800 858-8501 (ser vice en anglais seule- ment) pour obtenir de l’aide av ant de retourner l’article au magasin. En cas de problème , suivez ce guide. V ous pouvez aussi visiter notre site Web à www .hzsuppor t.com. Si le problème persiste , composez* le 1 800 858-8501 (service en angla ...

  • Heath Zenith Lighted Wireless Push Button Accessory - page 24

    -24- 598-1137-02 GARANTIE LIMITÉE DE 5 ANS Il s’agit d’une « Garantie limitée » qui vous confère des droits juridiques spécifiques. V ous pouvez également jouir d’autres droits, v ariables d’une province à l’autre. P end an t un e péri od e de 5 an s à com pt er de la dat e d’a cha t, to ute an oma li e de fo nc ti onn e- me ...

Manufacturer Heath Zenith Category Indoor Furnishings

Documents that we receive from a manufacturer of a Heath Zenith Lighted Wireless Push Button Accessory can be divided into several groups. They are, among others:
- Heath Zenith technical drawings
- Lighted Wireless Push Button Accessory manuals
- Heath Zenith product data sheets
- information booklets
- or energy labels Heath Zenith Lighted Wireless Push Button Accessory
All of them are important, but the most important information from the point of view of use of the device are in the user manual Heath Zenith Lighted Wireless Push Button Accessory.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Heath Zenith Lighted Wireless Push Button Accessory, service manual, brief instructions and user manuals Heath Zenith Lighted Wireless Push Button Accessory. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Heath Zenith Lighted Wireless Push Button Accessory.

Similar manuals

A complete manual for the device Heath Zenith Lighted Wireless Push Button Accessory, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Heath Zenith Lighted Wireless Push Button Accessory by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Heath Zenith Lighted Wireless Push Button Accessory.

A complete Heath Zenith manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Heath Zenith Lighted Wireless Push Button Accessory - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Heath Zenith Lighted Wireless Push Button Accessory, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Heath Zenith Lighted Wireless Push Button Accessory, that we can find in the current document
3. Tips how to use the basic functions of the device Heath Zenith Lighted Wireless Push Button Accessory - which should help us in our first steps of using Heath Zenith Lighted Wireless Push Button Accessory
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Heath Zenith Lighted Wireless Push Button Accessory
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Heath Zenith Lighted Wireless Push Button Accessory in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Heath Zenith Lighted Wireless Push Button Accessory?

Use the form below

If you did not solve your problem by using a manual Heath Zenith Lighted Wireless Push Button Accessory, ask a question using the form below. If a user had a similar problem with Heath Zenith Lighted Wireless Push Button Accessory it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)