English dropdown-ico

Manual Pelco ES30PC

70 pages 0.66 mb
Download

Go to site of 70

Summary
  • Pelco ES30PC - page 1

    ES30PC/ES31PC Esprit ® with Pressurized IOC INSTALLATION/OPERATION C311M-N (6/06) U.S. Patent D-472.260 ...

  • Pelco ES30PC - page 2

    ...

  • Pelco ES30PC - page 3

    C311M-N (6/06) 3 Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco ES30PC - page 4

    4 C311M-N (6/06) Turning Limit Stops On Or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Programming Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco ES30PC - page 5

    C311M-N (6/06) 5 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other ...

  • Pelco ES30PC - page 6

    6 C311M-N (6/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This ...

  • Pelco ES30PC - page 7

    C311M-N (6/06) 7 Description The ES30PC/ES31PC Esprit Series is designed to protect camera optics and electronics from moisture and airborne contaminants. The system features a receiver , pan and tilt, enclosure, and a pressurized integrated optics cartridge (IOC). The integrated optics cartridge packages an auto focus camera, lens, heater , and se ...

  • Pelco ES30PC - page 8

    8 C311M-N (6/06) Installation 1. When installing the ES30PC/ES31PC Esprit ® system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees. 2. Remove the transformer module from the base of the system by loosening the ...

  • Pelco ES30PC - page 9

    C311M-N (6/06) 9 4. Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. 5. ES30PC-5/ES31PC-5 Models Only – Set the 120/230 voltage selector switch on the transformer to the appropriate voltage. 6. Conn ...

  • Pelco ES30PC - page 10

    10 C311M-N (6/06) 7. Install mount; refer to the installation manual supplied with the mount for instructions. 8. T urn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the T roubleshooting section. 9. Plug the male Esprit system connector , located on the bottom of the p ...

  • Pelco ES30PC - page 11

    C311M-N (6/06) 11 c. Replace the plug. 11. Refer to the Operation and Programming sections for instructions on how to use your ES30PC/ES31PC Series Esprit integrated positioning system. ...

  • Pelco ES30PC - page 12

    12 C311M-N (6/06) TXB Series T ranslator Board Installation (Optional) Pelco’ s TXB Series allows controllers from other companies to communicate with the Esprit system. To install a TXB Series board, remove the left cover of the pan and tilt. Once the cover is removed, refer to the manual supplied with the translator board to complete the instal ...

  • Pelco ES30PC - page 13

    C311M-N (6/06) 13 TOP GASKET FRONT RAIN GUARD ...

  • Pelco ES30PC - page 14

    14 C311M-N (6/06) Operation POWER -UP DISPLAY When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For example, the screen might show the following information: HOW TO OPERATE Y OUR SYSTEM OPERATING NOTES ENVIRONMENTAL RANGE The operating temperature ranges from a minimum of -50 ...

  • Pelco ES30PC - page 15

    C311M-N (6/06) 15 PRESSURIZED INTEGRATED OPTICS CARTRIDGE The pressurized IOC houses an auto focus camera, lens, heater , and sensors in a self-contained, sealed unit. Dry nitrogen pressurized to 10 psig controls the environment inside the cartridge, eliminating internal condensation and corrosion. Sensors strategically placed inside the pressurize ...

  • Pelco ES30PC - page 16

    16 C311M-N (6/06) CURRENT READING MENU The Current Reading menu displays the existing status of temperature, pressure, and dewpoint inside the integrated optics cartridge. An asterisk displayed to the left of a menu item denotes that an alert condition exists. Due to the heat emitted from the electronics of the camera, normal temperature operating ...

  • Pelco ES30PC - page 17

    C311M-N (6/06) 17 ZONES A zone is a programmed pan area with set boundaries and identifying label. The Esprit system has a maximum of eight zones, each with a 20-character label. Zones can be programmed to blank video when the camera pans into the zone area. If a zone is blanked, the system displays the message, VIDEO BLANK. (Refer to Zone Blank in ...

  • Pelco ES30PC - page 18

    18 C311M-N (6/06) Programming – ES30PC16/ES31PC16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sync Menu Power Up Default Exit Power -Up Menu Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit *Wiper Menu Limit Stops Off Se ...

  • Pelco ES30PC - page 19

    C311M-N (6/06) 19 Programming – ES30PC22/ES31PC22 Gain Limit 7 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 66 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <Sharpness> <White balance> Prev Exit Next Menu Auto Sharpness On Sharpness 13 Exit Sharpness Menu Auto white bal On R-G ...

  • Pelco ES30PC - page 20

    20 C311M-N (6/06) Programming – ES30PCBW24/ES31PCBW24 Gain Limit 28 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 91 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Auto Auto focus mode Auto <IR Filter> <Sharpness> <White balance> Prev Exit Next Menu Auto Sharpness Sharpness On Exit Sharpness Menu I ...

  • Pelco ES30PC - page 21

    C311M-N (6/06) 21 Programming ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for v ...

  • Pelco ES30PC - page 22

    22 C311M-N (6/06) KBD4000/KBD4002/KBD4000V 1. Press the SPOT MONITOR key . 2. Enter 95, and then hold the PRESET key (approximately five seconds) until the main menu appears on the screen. MPT9500 Standard Coaxitron Mode 1. Enter 95 and press the PRESET SET key . 2. Position the asterisk in the YES row and press the F1 key . The main menu appears. ...

  • Pelco ES30PC - page 23

    C311M-N (6/06) 23 ACK ACT (ACKNOWLEDGE ACTION) If an enivornmental condition inside of the IOC goes outside of the factory set limits (such as “Low Pressure”) then select ACK Alert to activate the alert label behavior . Program ACK Act to establish alert label behavior after alert acknowledgement. The following acknowledge actions are available ...

  • Pelco ES30PC - page 24

    24 C311M-N (6/06) ALERT DISPLAY POSITION Screen positioning of the alert label is user -defined. Positioning options include the following: To set the alert label position: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Alert. 3. Press the Iris Open button to enter the Alert menu. 4. Position the cursor (> ...

  • Pelco ES30PC - page 25

    C311M-N (6/06) 25 ALERT REPEAT Y ou can program how often an ALERT label is repeatedly displayed until it is acknowledged by the system controller . The following settings are available: • Constant: The ALERT label is continually displayed on the monitor until acknowledged. • 15 min off: The ALERT label is displayed every 15 minutes for a 15-se ...

  • Pelco ES30PC - page 26

    26 C311M-N (6/06) AUTO FOCUS MODE There are two auto focus modes: • Auto: If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place the focus in the manual mode. The system will return to auto focus if you pan or tilt the unit or do a zoom function. • Off: If the mode is set to off, the dome will operate in the m ...

  • Pelco ES30PC - page 27

    C311M-N (6/06) 27 AUTO IRIS The following are the settings for auto iris: Mode, Level, and Peak. To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Auto Iris. 5. Press the Iri ...

  • Pelco ES30PC - page 28

    28 C311M-N (6/06) AUTO IR LEVEL (MODELS ES30PCBW24/ES31PCBW24) The auto IR level is the light level at which the infrared filter switches IN or OUT . Following are the available settings for the Auto IR Level: • DUSK (default): Approximately 6 lux (black-white), approximately 13 lux (color) • DARK: Approximately 0.1 lux (black-white), approxim ...

  • Pelco ES30PC - page 29

    C311M-N (6/06) 29 AUTO SHARPNESS The following settings are available for auto sharpness: • On: Automatically sets the sharpness of the camera. • Off: The sharpness of the camera needs to be manually set (refer to Sharpness). To change the mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Pr ...

  • Pelco ES30PC - page 30

    30 C311M-N (6/06) AZ/EL Az/El programs the horizontal display position of the Azimuth 1 /Elevation 2 label. NOTE: Az/El display is not available while you are programming or running a pattern. The following settings are available for the Az/El label: • Off: Label is not displayed. • Left (default): Label is displayed on the left-hand side of th ...

  • Pelco ES30PC - page 31

    C311M-N (6/06) 31 AZ/EL LINE Az/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Az/El display is not available while you are pr ...

  • Pelco ES30PC - page 32

    32 C311M-N (6/06) AZIMUTH ZERO Azimuth is the pan angle from 0 to 359 degrees. Azimuth zero is the programmed zero-degree point that is normally set to magnetic north. Once programmed, on-screen pan position (azimuth) and compass readings are based on the set azimuth zero point. To set azimuth zero: 1. Program preset 95 (28). The main menu appears. ...

  • Pelco ES30PC - page 33

    C311M-N (6/06) 33 BACKLIGHT COMPENSATION There are two backlight compensation modes: • On: The system uses the center 10 percent of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash out to white. The camera will adjust the iris so that the object in the sensitive area is properly exposed. NOTE: E ...

  • Pelco ES30PC - page 34

    34 C311M-N (6/06) DIRECTION Direction programs the horizontal display position of the Direction label (N, NW , NE, …). NOTES: • For direction to be accurate, azimuth zero must be set to magnetic north. • Direction display is not available while you are programming or running a pattern. The following settings are available for the Direction la ...

  • Pelco ES30PC - page 35

    C311M-N (6/06) 35 DIRECTION LINE Direction Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Direction display is not available while you ar ...

  • Pelco ES30PC - page 36

    36 C311M-N (6/06) DISPLAY DURATION Display Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor . The available settings for display duration include the following: • Constant: The label is displayed continuously . • 2 Seconds (default): The label is displayed for 2 seconds after PTZ functions end. ? ...

  • Pelco ES30PC - page 37

    C311M-N (6/06) 37 GAIN/AGC GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button ...

  • Pelco ES30PC - page 38

    38 C311M-N (6/06) IR FILTER MODE (MODELS ES30PCBW24/ES31PCBW24) There are two settings for the IR filter mode: IMPORT ANT : Automatic shutter speed must be set to Auto for the IR filter to operate automatically . If the automatic shutter speed is disabled, the IR filter setting will automatically switch to OFF . • Auto: IR filter switches in ...

  • Pelco ES30PC - page 39

    C311M-N (6/06) 39 LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits). T URNING LIMIT STOPS ON OR OFF To change the limit stop mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to en ...

  • Pelco ES30PC - page 40

    40 C311M-N (6/06) Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Man Limits and press the Iris Open button. PRE ...

  • Pelco ES30PC - page 41

    C311M-N (6/06) 41 Limit Stops Menu The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu. 4. Move the cursor to Set Scan Limits and press the Iris Open button. PR ...

  • Pelco ES30PC - page 42

    42 C311M-N (6/06) LINE SYNCHRONIZATION If cameras are out of phase with each other , they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: • On: Adjust the synchronization of the power line voltage so that it is in phase with other cameras. • Off: The system synchroniz ...

  • Pelco ES30PC - page 43

    C311M-N (6/06) 43 LOWLIGHT LIMIT (MODELS ES30PC22/ES31PC22 AND ES30PCBW24/ES31PCBW24 ONLY) This setting determines the maximum length of time the shutter will remain open automatically in low light conditions. There are six choices: NOTES: • LOWLIGHT does not mean NO LIGHT . Some type of illumination is required. • Auto focus is automatically t ...

  • Pelco ES30PC - page 44

    44 C311M-N (6/06) PARK T IME MINUTES This feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity . The time can be set from 1 minute to 720 minutes (12 hours), or it can be set to zero, which disables this feature. NOTE: Preset 1 must be programmed for the system to park. To change the park time: 1. ...

  • Pelco ES30PC - page 45

    C311M-N (6/06) 45 PATTERN LENGTH The Esprit can do the following: • One full pattern that is 1.5, 3, or 6 minutes long. • T wo half patterns that is .75, 1.5, or 3 minutes long. This pattern can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be enabled while running a ...

  • Pelco ES30PC - page 46

    46 C311M-N (6/06) POWER -UP MODE This feature lets the dome resume a desired condition following power -up. The menu includes the following choices. • Default: On power -up, the system goes through a configuration cycle and stops at zero reference, showing “Configuration Done,” address, and mode settings on the screen. • Park: The system ...

  • Pelco ES30PC - page 47

    C311M-N (6/06) 47 PROPORTIONAL PAN There are two proportional pan modes: • On: Enables the proportional pan mode. The amount of zoom controls the pan and tilt. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the m ...

  • Pelco ES30PC - page 48

    48 C311M-N (6/06) RESET CAMERA Resetting the camera returns the settings to their defaults. T urning off power does not reset the camera. Camera settings are retained in memory . When the power is turned back on, the settings will be the same as they were when the power was turned off. To reset the camera: 1. Program preset 95 (28). The main menu a ...

  • Pelco ES30PC - page 49

    C311M-N (6/06) 49 SCAN SPEED The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan. To change the scan speed: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other . 3. Press the Iris Open button to enter the menu entitled Other . 4. Position t ...

  • Pelco ES30PC - page 50

    50 C311M-N (6/06) SHARPNESS Use the Sharpness setting to manually set the sharpness of the camera. To manually set the sharpness of the camera: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Next. Press the Ir ...

  • Pelco ES30PC - page 51

    C311M-N (6/06) 51 SHUTTER SPEED There are several electronic shutter speed settings: In the Auto setting the camera controls the shutter speed automatically . Increasing the shutter speed lowers the light sensitivity , but rapidly moving objects will be less blurred. NOTE: (ES30PCBW24/ES31PCBW24) If the IR Filter Mode is set to Auto, the Shutter Sp ...

  • Pelco ES30PC - page 52

    52 C311M-N (6/06) SPEED PROFILE This feature allows the operator to set the wind speed conditions for the location of the Esprit system. Y ou can set two wind speed profiles of 50 mph or 90 mph in which the system will remain operational. In both settings, the pan speed will be a maximum of 40 degrees per second. The difference will be in the turb ...

  • Pelco ES30PC - page 53

    C311M-N (6/06) 53 WHITE BALANCE The settings for white balance are as follows: • Auto white bal • R Gain • B Gain To change the white balance settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the Camera menu. 4. Position the cursor (>) beside Next ...

  • Pelco ES30PC - page 54

    54 C311M-N (6/06) WIPER MODE There are three wiper settings: • Wiper Mode (Momentary or Continuous) • Wiper Dwell • Wiper T ime To change the wiper settings: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Wiper . 3. Press the Iris Open button to enter the Wiper menu. 4. Move the joystick up or down to p ...

  • Pelco ES30PC - page 55

    C311M-N (6/06) 55 ZONES Basic rules for setting zones: 1. Refer to the documentation for your control system to program zones. 2. Establish zones using the controller , prior to programming ZONE BLANK with the Esprit onscreen menu. 3. T o accurately set zone areas, zoom wide to the maximum field of view . 4. Set zones moving the joystick left to r ...

  • Pelco ES30PC - page 56

    56 C311M-N (6/06) ZOOM Zoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label: • Off: Label is not displayed. • Left: Label is displayed on the left-hand side of the screen. • Center (default): Label is displayed in the center of the screen. • Right: Label is displayed on the ...

  • Pelco ES30PC - page 57

    C311M-N (6/06) 57 ZOOM LIMIT ES30PC16/ES31PC16: 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X. ES30PC22/ES31PC22: 22X optical zoom and 10X electronic zoom, can be set for 22X, 32X, 88X, 176X, or 220X. ES30PCBW24/ES31PCBW24: 24X optical zoom and 10X electronic zoom, can be set for 24X, 32X, 96X, 192X, or 240X. ...

  • Pelco ES30PC - page 58

    58 C311M-N (6/06) ZOOM LINE Zoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3 is the third line from the top of the screen and line 10 is located at the bottom of the screen. Line 10 is the default setting. NOTE: Zoom display is not available while you are programming or run ...

  • Pelco ES30PC - page 59

    C311M-N (6/06) 59 T roubleshooting NOTE: The system contains no user -serviceable parts. If there is a problem with your system, it must be returned to Pelco for servicing. Symptom: System does not operate. 1. Check system input voltage. 2. The Esprit system is protected by a resettable overcurrent protective device located in the transformer modul ...

  • Pelco ES30PC - page 60

    60 C311M-N (6/06) 5. Check for normal load termination of 75 ohms. When looping through VCRs or multiplexers, make sure the signal is terminated at the end device. Some termination symptoms and problems are listed below . Symptom Problem Extremely bright video No termination or high resistance Over contrast or contrast level of monitor needs to Dou ...

  • Pelco ES30PC - page 61

    C311M-N (6/06) 61 Maintenance Clean the enclosure window periodically with a mild non-abrasive detergent in water and a soft cloth to help maintain picture clarity . If operating problems are experienced with the system, refer to the T roubleshooting section. WIPER If the window wiper assembly is installed, replace worn or deteriorated wiper blades ...

  • Pelco ES30PC - page 62

    62 C311M-N (6/06) PRESSURIZED IOC IMPORT ANT : Disconnect power to the Esprit system before removing or installing the pressurized cartridge. Software conflicts can occur if the Esprit is not powered-down before removing/installing the IOC. There are no user -serviceable parts internal to the pressurized integrated optics cartridge. If vessel fail ...

  • Pelco ES30PC - page 63

    C311M-N (6/06) 63 Appendix NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switch settings have no effect on Coaxitron control signals. *SW1-3 is not used; set it in the OFF position. *SW1-4 is not used; set it in the OFF position. T able A. Switch Set ...

  • Pelco ES30PC - page 64

    64 C311M-N (6/06) T able B. Switch Settings for SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals. Receiver Address P-T ype D-T ype Control Control Switch Setting SW2-1 SW2-2 SW2-3 SW2 ...

  • Pelco ES30PC - page 65

    C311M-N (6/06) 65 – 112 OFF OFF OFF OFF ON ON ON OFF – 113 ON OFF OFF OFF ON ON ON OFF – 114 OFF ON OFF OFF ON ON ON OFF – 115 ON ON OFF OFF ON ON ON OFF – 116 OFF OFF ON OFF ON ON ON OFF – 117 ON OFF ON OFF ON ON ON OFF – 118 OFF ON ON OFF ON ON ON OFF – 119 ON ON ON OFF ON ON ON OFF – 120 OFF OFF OFF ON ON ON ON OFF – 121 ON O ...

  • Pelco ES30PC - page 66

    66 C311M-N (6/06) – 234 OFF ON OFF ON OFF ON ON ON – 235 ON ON OFF ON OFF ON ON ON – 236 OFF OFF ON ON OFF ON ON ON – 237 ON OFF ON ON OFF ON ON ON – 238 OFF ON ON ON OFF ON ON ON – 239 ON ON ON ON OFF ON ON ON – 240 OFF OFF OFF OFF ON ON ON ON – 241 ON OFF OFF OFF ON ON ON ON – 242 OFF ON OFF OFF ON ON ON ON – 243 ON ON OFF OFF ...

  • Pelco ES30PC - page 67

    C311M-N (6/06) 67 Specifications ELECTRICAL Input V oltage 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset feature enabled when power becomes unstable or interrupted. Power Requirements Maximum power consumption is 70 VA per system Heater and Defroster Thermostatically controlled heater consumes 10 watts and cycles ...

  • Pelco ES30PC - page 68

    68 C311M-N (6/06) Focus Automatic and manual override Sensitivity ES30PC16/ES31PC16 0.05 lux at 1/2-second shutter speed (NTSC) 0.05 lux at 1/1.5-second shutter speed (P AL) ES30PC22/ES31PC22 0.02 lux at 1/2-second shutter speed (NTSC) 0.02 lux at 1/1.5-second shutter speed (P AL) ES30PCBW24/ES31PCBW24 0.005 lux at 1/2-second shutter speed (color , ...

  • Pelco ES30PC - page 69

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted ...

  • Pelco ES30PC - page 70

    United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East ® W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco ES30PC can be divided into several groups. They are, among others:
- Pelco technical drawings
- ES30PC manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco ES30PC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco ES30PC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco ES30PC, service manual, brief instructions and user manuals Pelco ES30PC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco ES30PC.

Similar manuals

A complete manual for the device Pelco ES30PC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco ES30PC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco ES30PC.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco ES30PC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco ES30PC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco ES30PC, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco ES30PC - which should help us in our first steps of using Pelco ES30PC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco ES30PC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco ES30PC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco ES30PC?

Use the form below

If you did not solve your problem by using a manual Pelco ES30PC, ask a question using the form below. If a user had a similar problem with Pelco ES30PC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)