English dropdown-ico

Manual Pelco C2406M-F

16 pages 0.25 mb
Download

Go to site of 16

Summary
  • Pelco C2406M-F - page 1

    200 Series Camclosure ® Integrated Camera System C2406M-F (4/04) ® INST ALLA TION/OPERA TION ...

  • Pelco C2406M-F - page 2

    2 C2406M-F (4/04) IMPORT ANT SAFEGUARDS AND WARNINGS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or ...

  • Pelco C2406M-F - page 3

    C2406M-F (4/04) 3 DESCRIPTION The wedge style 200 Series Camclosure ® integrated camera system is designed to mount directly to a wall or ceiling. It also can mount to a corner with the ICS200-CM corner mount. The system incorporates a camera and lens package into a small, medium security enclosure. ...

  • Pelco C2406M-F - page 4

    4 C2406M-F (4/04) INST ALLA TION The following parts are supplied: 1 Camclosure integrated camera system 1W atertight mounting plate 1 1/8-inch pin-in-hex Allen wrench bit 3 10-32 x 0.5-inch Phillips screws 3 #10 internal tooth lock washers 1 Hole plug PREP ARE MOUNTING SURFACE 1. Remove the cover of the ICS200. Use the screwdriver bit that is prov ...

  • Pelco C2406M-F - page 5

    C2406M-F (4/04) 5 INST ALL BASE WITHOUT CONDUIT 1. Outdoor Installation Only – Bring the power and video wiring for the camera through the wiring hole in the watertight mounting plate. Then fasten the mounting plate to the mounting surface with #8 stainless steel screws (not provided) of the appropriate length. 2. Connect power input wires to the ...

  • Pelco C2406M-F - page 6

    6 C2406M-F (4/04) bottom of the base (refer to Figure 5). Pull the wiring inside the base. WARNING: Be careful not to damage the wiring or the connection where the video cable is fastened to the circuit board. 3. Using the screwdriver bit that is provided, remove the conduit cover and plate by unscrewing the tamperproof screw . Refer to Figure 6. 4 ...

  • Pelco C2406M-F - page 7

    C2406M-F (4/04) 7 REINST ALL CAMERA MODULE 1. Reinstall the camera module. Refer to Figure 8. Make sure the top of the camera is oriented properly . On the lens housing, look for the label that says TOP . WARNING: To prevent damage to the camera or lens, the camera must be installed in the proper hole of the mounting bracket. If the camera is not i ...

  • Pelco C2406M-F - page 8

    8 C2406M-F (4/04) ADJUSTMENTS (COLOR CAMERA ONL Y) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however , adjustments may be necessary . 1. Remove the cover using the supplied 1/8-inch hollow screwdriver bit. 2. Adjust the vertical phase, iris level, focus, or switch settings (refer to pro ...

  • Pelco C2406M-F - page 9

    C2406M-F (4/04) 9 FOCUS ADJUSTMENT FOR FIXED FOCAL LENGTH LENS WITH AUTO IRIS To adjust the focus, do the following: 1. Loosen the locking screw on the bottom of the lens. T o loosen the screw , it may be necessary to remove the heater board. Refer to Figure 14 and the accompanying steps. 2. Move the screw in the slot to bring the picture into focu ...

  • Pelco C2406M-F - page 10

    10 C2406M-F (4/04) SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to Figure 16. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details. M ...

  • Pelco C2406M-F - page 11

    C2406M-F (4/04) 11 SWITCH SETTINGS FOR VARIFOCAL LENS The high resolution camera with varifocal lens and auto iris is configured at the factory for optimal performance in lighting conditions where auto iris is required. It is also configured with the shutter speed set at 1/60 (NTSC) or 1/50 (P AL) and AGC set at 6 dB of gain. To enable automatic ex ...

  • Pelco C2406M-F - page 12

    12 C2406M-F (4/04) (Design and product specifications subject to change without notice.) SPECIFICA TIONS General Pan/T ilt Adjustment: Manual; ± 10 ° pan; 5 ° above horizontal to 20 ° below horizontal tilt; additional 24 ° pan adjustment when installing using the adjustable mounting pattern in base Rating: Meets NEMA T ype 4 and IP66 standards ...

  • Pelco C2406M-F - page 13

    C2406M-F (4/04) 13 REGULA TORY NOTICES FCC Class A (monochrome, EIA cameras only) This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial ...

  • Pelco C2406M-F - page 14

    14 C2406M-F (4/04) W ARRANTY AND RETURN INFORMA TION W ARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC ...

  • Pelco C2406M-F - page 15

    C2406M-F (4/04) 15 REVISION HISTORY Manual # Date Comments C2406M 11/99 Original version. 1/00 Revised installation instructions. Added FCC notices. C2406M-A 2/00 Added varifocal lens. Changed format. C2406M-B 11/00 New camera module design, revised installation instructions. C2406M-C 1/01 Revised heater element caution. C2406M-D 1/03 Revised manua ...

  • Pelco C2406M-F - page 16

    World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO 9001 ® Orangeburg, New York | Las Vegas, Nevada | Eindhoven, The Netherlands | Wokingham, United Kingdom | Montreal, Canada | Singapore ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco C2406M-F can be divided into several groups. They are, among others:
- Pelco technical drawings
- C2406M-F manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C2406M-F
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C2406M-F.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C2406M-F, service manual, brief instructions and user manuals Pelco C2406M-F. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C2406M-F.

Similar manuals

A complete manual for the device Pelco C2406M-F, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C2406M-F by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C2406M-F.

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C2406M-F - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C2406M-F, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C2406M-F, that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C2406M-F - which should help us in our first steps of using Pelco C2406M-F
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C2406M-F
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C2406M-F in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C2406M-F?

Use the form below

If you did not solve your problem by using a manual Pelco C2406M-F, ask a question using the form below. If a user had a similar problem with Pelco C2406M-F it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)