English dropdown-ico

Manual Husqvarna 2000

17 pages 0.62 mb
Download

Go to site of 17

Summary
  • Husqvarna 2000 - page 1

    HUSQV ARNA CONSTRUCTION PR ODUCTS Soff-Cut 2000 Please read the operator’ s manual carefully and make sur e you understand the instructions before using the machine. US Oper ator’ s manual ...

  • Husqvarna 2000 - page 2

    CONTENTS Content Page T able of contents ………………………….. 2 Unpacking .................................................. 2 T ransporting ............................................... 2 Sound Data ................................................ 2 I ntroduction, personal safety ...................... 3 Registration of the product ? ...

  • Husqvarna 2000 - page 3

    INTRODUCTION Common sense: The focus of this manual is HOW to operate and service the equipment safely . It is not possible to cover every conceivable situation you can face when using this equipment. Therefore use this product only in a manner described in this manual. Operation or handling the machine in any other manner can lead to serious injur ...

  • Husqvarna 2000 - page 4

    4 REGISTER THE PRODUCT Please register your new 2000 with Husqvarna Construction Products by mailing in the registration card that came with the machine or you can register on the internet site www .husqvarnawarranty .com Registration will allow us to contact in case of any critical updates or recalls on this machine. W arranty registration has als ...

  • Husqvarna 2000 - page 5

    5 SAFETY W ARNINGS W ARNING Failure to comply with the following warnings could result in serious bodily injury or death! PERSONAL SAFETY • Read and understand instructions before operating saw . • Always wear safety approved hearing, eye, head and respiratory protection. • Wear boots with non-slip soles to provide proper footing. Steel-toed ...

  • Husqvarna 2000 - page 6

    6 EXCEL SERIES BLADES The Excel Series of diamond blades have been designed specically for the Soff-Cut Ultra Early Entry dry cutting system of green concrete. These specialty blades are designed to increase speed and life while cutting a wide range of aggregates. Choose the correct specication of diamond blade for your area as follows: Purpl ...

  • Husqvarna 2000 - page 7

    WHA T IS WHA T H E What is what? A. Oil ll & dipstick B. Air cleaner C. Recoil starter D. Fuel shut of f lever E. Choke lever F . Oil drain hose G. Fuel cap H. Fuel tank I. T ransmission oil ll cap J. Hour meter/T achometer K. Battery box L. Saw forward speed lever M. Engine on/off switch N. Guide arm lever O. Blade depth release lever P ...

  • Husqvarna 2000 - page 8

    8 OPERA TING INSTRUCTIONS Experience is very important when running the 2000 saw . A skilled worker is highly recommended. Always do an inspec- tion of the saw before starting the engine. Check the fuel (H) and oil level (A) per the enclosed engine manual. SAE 10W/30 oil and unleaded gasoline with an 87 or higher octane should be used. The hydrosta ...

  • Husqvarna 2000 - page 9

    9 FUEL HANDLING PROPER FUEL T aking the following precautions will lessen the risk of injury and property damage: - Use extreme care in handling gasoline. It is extremely ammable and the vapors are explosive. - Extinguish all cigarettes, cigars, pipes, and other sources of ignition. - Use only approved gasoline containers. - Never remove gas cap ...

  • Husqvarna 2000 - page 10

    10 Engine Oil Checking, Adding and Changing Oil Check the engine oil level (B) daily with saw fully lowered and the engine level. See the enclosed Robin manual for more details. Use SAE 10W-30 viscosity detergent automotive type with API service class SE or higher grade oil. Note: Engine holds approximately 1.0 quart (1.0 liter) when changing. Chan ...

  • Husqvarna 2000 - page 11

    11 OTHER MAINTENANCE Guards Check all guards for damage and proper function daily espe- cially the blade block. Blade block and cover should be secure to the saw and not damaged. Lexan side covers on the blade block should move freely up and down. Diamond blade Inspect diamond blades daily for damage, cracks, secure t to the arbor , loss of segm ...

  • Husqvarna 2000 - page 12

    12 As concrete hydrates or cures and begins to set, it develops internal stresses which may cause random cracks. Random cracks cast doubt on the quality and workmanship of the concrete. Contraction joints are cut in concrete to relieve these stresses before they seek their own relief in the form of random crack. The Sof f-Cut Ultra Early Entry syst ...

  • Husqvarna 2000 - page 13

    13 “ The timing of concrete operations - especially nishing and jointing - is critical” , states a quote from the foreword of the American Concrete Institute (ACI) 302.1 R-96. It goes on to say that “Failure to address this issue can contribute to unde- sirable characteristics in the wearing surface as cracking...” (It mentions other pro ...

  • Husqvarna 2000 - page 14

    14 TROUBLESHOOTING ENGINE RUNS ROUGH, BACK FIRES OR CAN NOT REACH FULL SPEED - Check if there is fuel in the tank and it is the correct fuel. Make sure there is no water in the fuel. - Check that the spark plugs are clean and properly gapped. - Check that choke is in the “off” position after engine is warm. - Check that air lter is not dirty ...

  • Husqvarna 2000 - page 15

    TECHNICAL SPECIFICA TIONS Engine Model Robin EX 27 Engine oil volume, quarts/liters 1.0/1.0 Gasoline tank volume, gal/liters 1.6/6.1 T ype Air cooled, 4-cycle, single slant cylinder , overhead camshaft, gasoline engine Air fi lter Cyclonic type Oil system Oil alert with auto shut down sensor Muf fl er Silent type 80 dbA, exhaust de fl ector , sp ...

  • Husqvarna 2000 - page 16

    16 W ARRANTY HUSQV ARNA EQUIPMENT W ARRANTY New 2000 sold by Husqvarna Construction Products are warranted to be free from manufacturing defects in nor- mal service for a period of six (6) months for labor and up to one (1) year on parts from date of purchase by the original consumer purchaser or date of introduction into rental company eet. Our ...

  • Husqvarna 2000 - page 17

    1 153477-95 2009-12-29 w ww .hu sqvarnacp .com ´®z+UOo¶5N¨ ´®z+UOo¶5N¨ Original instructions ...

Manufacturer Husqvarna Category Chainsaw

Documents that we receive from a manufacturer of a Husqvarna 2000 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 2000 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 2000
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 2000.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 2000, service manual, brief instructions and user manuals Husqvarna 2000. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 2000.

Similar manuals

A complete manual for the device Husqvarna 2000, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 2000 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 2000.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 2000 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 2000, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 2000, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 2000 - which should help us in our first steps of using Husqvarna 2000
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 2000
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 2000 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 2000?

Use the form below

If you did not solve your problem by using a manual Husqvarna 2000, ask a question using the form below. If a user had a similar problem with Husqvarna 2000 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)