English dropdown-ico

Manual Henny Penny CSB

11 pages 0.72 mb
Download

Go to site of 11

Summary
  • Henny Penny CSB - page 1

    CSL CSM CSB 62 INTRODUCTION This section provides the installation instr uctions for the Henny Penny Electric Combi-Steamers. NOTE: The installation of this unit must conform to all local, state, and federal codes. In the absence of codes use ANSI/NFP A No. 70-latest edition. NOTE: Canadian installations must conform with the Canadian electrical co ...

  • Henny Penny CSB - page 2

    CSL CSM CSB 63 Installation – Electric Units (continued) Floor Units: NOTE: Adequate clearance must be provided for ser vicing and for operation. Minimum clearances have to be maintained from the adjacent walls. Left Side Right Side Back Side CSB, CSM, CSL-20, 40 14” (350mm) 2” (50mm) 2” (50mm) Place the combi-steamer on a level and sturdy ...

  • Henny Penny CSB - page 3

    CSL CSM CSB 64 ELECTRICAL SUPPL Y Standard electrical supply for all Combi-Steamers is 208-240 volt, 3 phase, 50-60 Hz. NOTE: The power connections are located behind the ser vice door (see section 5-3). Each unit requir es a separate fused ser vice accor ding to the following table: (3 phase only) Model V oltage Phase Amps Load CSL/M/B-6 208V 3 27 ...

  • Henny Penny CSB - page 4

    CSL CSM CSB 65 WA TER SUPPLY The Combi-Steamer should only be connected to a cold water supply which meets the quality requir ements by the EPA on drinking water . Soft water must be at least 5 or 6 grains. The recommended water supply pr essure is 44 psi, but 22 to 87 psi will work. The water connection is done on a 3/4” NPT thread fitting, and ...

  • Henny Penny CSB - page 5

    CSG 66 INSTALLA TION GAS UNITS This section provides the installation instr uctions for the Henny Penny Gas Combi-Steamers NOTE: The installation must conform with local codes or in the absence of local codes, with ANSI Z223.1 latest edition and electrical code ANSI/NFP A No. 70 latest edition. NOTE: For Canadian installations it should be done in ...

  • Henny Penny CSB - page 6

    CSG 67 Minor unevenness of the sur face/floor can be compensated by adjusting the metal legs of the stand or the appliance. The weight of the units are as follows: CSG-10 556 lbs. (252 Kg) CSG-12 529 lbs. (240 Kg) CSG-20 1015 lbs. (460 Kg) VENTILA TION-CSG The gas Combi-Steamers all should be located with a provision for venting into an adequate ex ...

  • Henny Penny CSB - page 7

    CSG 68 WA TER SUPPLY-CSG The Combi-Steamer should only be connected to a cold water supply which meets the quality requir ements by the EP A on drinking water . Soft water must be at least 5 or 6 grains. The recommended water supply pr essure is 44 psi, but 22 to 87 psi will work. The water connection is done on a 3/4” NPT thread fitting, and a m ...

  • Henny Penny CSB - page 8

    CSG 69 Installation – Gas Units (continued) ELECTRICAL SUPPL Y -CSG The gas Combi-Steamer requir es 120 volt, single phase, 60 Her tz, 15 amp, 3 wire grounded ser vice. The gas unit is factor y equipped with a gr ounded cord and plug. NOTE: The unit will not function and the reset signal will stay on with the white wire connected to the live blac ...

  • Henny Penny CSB - page 9

    CSG 70 GAS SUPPL Y -CSG RIGHT MINIMUM PULL of equipment away from wall permissible for accessibility to Quick Disconnect Device WRONG A VOID SHARP BENDS AND KINKS when pulling equipment away from wall. (Maximum pull will kink ends, even if installed properly , and reduce Connector life.) Couplings and hose should be installed in the same plane as s ...

  • Henny Penny CSB - page 10

    CSG 71 GAS SUPPL Y (continued) A steam bur ner gas valve and dr y heat bur ner gas valve r espectively are responsible for the gas supply to the indi- vidual bur ners. The Combi-Steamer models CSG have manual shut-of f valves, that can be r eached from the front without tools. The manual shut-of f valves of these units are located behind the ser vi ...

  • Henny Penny CSB - page 11

    CSG 72 NOTE: After turning on the gas, the manual shut-of f valve must remain open, except during pressure testing as outlined in the above steps, or when necessar y during service maintenance. This incoming pressur e reading can be taken by installing a gas pressur e gauge on the front of the unit’s main gas valves test por t. This should be don ...

Manufacturer Henny Penny Category Electric Steamer

Documents that we receive from a manufacturer of a Henny Penny CSB can be divided into several groups. They are, among others:
- Henny Penny technical drawings
- CSB manuals
- Henny Penny product data sheets
- information booklets
- or energy labels Henny Penny CSB
All of them are important, but the most important information from the point of view of use of the device are in the user manual Henny Penny CSB.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Henny Penny CSB, service manual, brief instructions and user manuals Henny Penny CSB. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Henny Penny CSB.

Similar manuals

A complete manual for the device Henny Penny CSB, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Henny Penny CSB by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Henny Penny CSB.

A complete Henny Penny manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Henny Penny CSB - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Henny Penny CSB, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Henny Penny CSB, that we can find in the current document
3. Tips how to use the basic functions of the device Henny Penny CSB - which should help us in our first steps of using Henny Penny CSB
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Henny Penny CSB
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Henny Penny CSB in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Henny Penny CSB?

Use the form below

If you did not solve your problem by using a manual Henny Penny CSB, ask a question using the form below. If a user had a similar problem with Henny Penny CSB it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)