English dropdown-ico

Manual Tiger Products Co., Ltd NH TS100-135A

20 pages 0.33 mb
Download

Go to site of 20

Summary
  • Tiger Products Co., Ltd NH TS100-135A - page 1

    PAGE - 1 INSTRUCTIONS SWEEPER ASSEMBLIES NH TS100-135A 06020012 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www.tiger-mowers.com Current as of 6/1 1/07 MOUNTING AND OPERATING PARTS LISTING WITH ...

  • Tiger Products Co., Ltd NH TS100-135A - page 2

    PAGE - 2 FORWARD 2 TABLE OF CONTENTS 2 SAFETY PERCAUTIONS 3 OPERATIONAL SAFETY PRECAUTIONS 4 OPERATION 5 IMPORTANT INSTRUCTIONS 7 MOUNTING INSTRUCTIONS 8 LEVELING INSTRUCTIONS 10 SUPPORT YOKE ADJUSTMENT 12 BRUSH REPLACEMENT 13 MOTOR AND HUB REPLACEMENT 14 MAINTENANCE SCHEDULE 15 PARTS SECTION 16 CONTENTS FORWARD This manual contains information abo ...

  • Tiger Products Co., Ltd NH TS100-135A - page 3

    PAGE - 3 This symbol means: CAUTION ! Your safety is at rick ! – Any R.O.P.S. (roll over protective structure) should not be drilled, welded on, or altered in any manner. Any alteration may reduce your protection. – Do not bypass the tractor neutral safety swith. Jumping or bypassing can cause tractor runaway. – Do not allow any persons on th ...

  • Tiger Products Co., Ltd NH TS100-135A - page 4

    PAGE - 4 OPERATIONAL SAFETY PRECAUTIONS This symbol means: CAUTION ! Your safety is at rick ! – Reduce speed when turning, taking curves, rough ground, or hillsides to reduce chance of rollover. – Always keep tractor in gear when traveling downhill to prevent runaway. – When driving on a road, day or night, use lighting and markings required ...

  • Tiger Products Co., Ltd NH TS100-135A - page 5

    PAGE - 5 OPERATION Be sure the ball valves on the mower hydraulic tank are OPEN before starting the tractor. Serious damage to the hydraulic system can occur if the valves are not OPEN. For brush operation: open the high pressure valve located near the pressure port of the pump and close the high pressure valve located near the electrical solenoid. ...

  • Tiger Products Co., Ltd NH TS100-135A - page 6

    PAGE - 6 It is very possible to cut brush life by 50% if the frame is not level. Running an unlevel brush is jast like throwingmoney out the window. The small amount of time spent leveling a brush before sweeping is paed back many times over in longer brush life. As a general rule brush level should be checked every day before operating. Uneven bru ...

  • Tiger Products Co., Ltd NH TS100-135A - page 7

    PAGE - 7 1. Do not store sweeper polypropylene brushes in direct sunlight! Direct sunlight will cause the bristles to deteriorate, causing the bristles to become brittle. If the broom is to be stored for any length of time, store it in the shade, inside, or cover the brush with a tarp to protect it from the sun. 2. Do not stor the sweeper power bro ...

  • Tiger Products Co., Ltd NH TS100-135A - page 8

    PAGE - 8 MOUNTING INSTRUCTIONS Please rea and understand the instructions and schematics completely before beginning assembly. Parts and drawings may vary slightly due to the variety of tractor makes and models. The mounting kit you receive should be correct for your application. If questions arise please contact your local dealer or Tiger Service ...

  • Tiger Products Co., Ltd NH TS100-135A - page 9

    PAGE - 9 11. The spring - chain assemblies are used to help support the weight of the brush head assembly when in the sweeping position. Hook on spring to each of the outside holes in the top plate of the brushhead upright. The chains are con nected to the outside slots in the chain holder on the spring - chain assembly. The spring - chain assembli ...

  • Tiger Products Co., Ltd NH TS100-135A - page 10

    PAGE - 10 LEVELING INSTRUCTIONS The sweeper must be leveled t maintain even brush wear and to produce efficient sweeping action. If the broom is not leveled at first and periodically after that, then it will put stress on certain parts causing excessive wear. The broom is easily leveled if these steps are followed. 1. Drive the assembled broom onto ...

  • Tiger Products Co., Ltd NH TS100-135A - page 11

    PAGE - 11 Make a note of the measurements. Swing the brush head assembly to the left and take the same measurements. If the measurements are not equal, refer to previous leveling steps and illustrations for adjustments. LEVELING INSTRUCTIONS CONTINUED 5. After leveling, tighten the brush head mounting bolts E, F and G ...

  • Tiger Products Co., Ltd NH TS100-135A - page 12

    PAGE - 12 SUPPORT YOKE ADJUSTMENT NOTE: This section applies only to units with serial number 75146 and above. Units with serial number below 75146 do not have adjustable support yokes. Before operating the sweeper the brush head frame support yokes should be checked and if necessary adjusted as follows: 1. Loosen the two 5/8” carriage bolts in e ...

  • Tiger Products Co., Ltd NH TS100-135A - page 13

    PAGE - 13 BRUSH REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place. Lift the hood off the brush and set aside. 3. Remove the two carriage bolts in the ...

  • Tiger Products Co., Ltd NH TS100-135A - page 14

    PAGE - 14 MOTOR AND HUB REPLACEMENT 1. Disconnect the two hydraulic hoses at both motors. IMPORTANT: Tape over the ends of the hydraulic hoses and the hydraulic motor ports to prevent contamination of the hydraulic system. 2. Remove the four bolts holding the hood in place. Lift the hood off the brush and set aside. 3. Remove the two carriage bolts ...

  • Tiger Products Co., Ltd NH TS100-135A - page 15

    PAGE - 15 ...

  • Tiger Products Co., Ltd NH TS100-135A - page 16

    PAGE - 16 TRACTOR MOUNT - MAIN FRAME ...

  • Tiger Products Co., Ltd NH TS100-135A - page 17

    PAGE - 17 TRACTOR MOUNT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 34857 1 MTG,THS 2 06410443 1 MNT,LH,SWPR,CNH,TSA 2 06410442 1 MNT,RH,SWPR,CNH,TSA 4 06430049 4 SPACER,2.00x1.00x3.34 5 41644 1 PLATE,ATTACHING 6 21735 4 CAPSCREW,1/2 x 2 1/2,NC 7 24879 4 CAPSCREW , 20MM x 65MM(2.5 PITCH) 8 21843 4 CAPSCREW 3/4” x 6” NC 9 33880 4 FLATWASHER, 3 ...

  • Tiger Products Co., Ltd NH TS100-135A - page 18

    PAGE - 18 ...

  • Tiger Products Co., Ltd NH TS100-135A - page 19

    PAGE - 19 ...

  • Tiger Products Co., Ltd NH TS100-135A - page 20

    PAGE - 20 ...

Manufacturer Tiger Products Co., Ltd Category Lawn Mower

Documents that we receive from a manufacturer of a Tiger Products Co., Ltd NH TS100-135A can be divided into several groups. They are, among others:
- Tiger Products Co., Ltd technical drawings
- NH TS100-135A manuals
- Tiger Products Co., Ltd product data sheets
- information booklets
- or energy labels Tiger Products Co., Ltd NH TS100-135A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tiger Products Co., Ltd NH TS100-135A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tiger Products Co., Ltd NH TS100-135A, service manual, brief instructions and user manuals Tiger Products Co., Ltd NH TS100-135A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tiger Products Co., Ltd NH TS100-135A.

Similar manuals

A complete manual for the device Tiger Products Co., Ltd NH TS100-135A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tiger Products Co., Ltd NH TS100-135A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tiger Products Co., Ltd NH TS100-135A.

A complete Tiger Products Co., Ltd manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tiger Products Co., Ltd NH TS100-135A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tiger Products Co., Ltd NH TS100-135A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tiger Products Co., Ltd NH TS100-135A, that we can find in the current document
3. Tips how to use the basic functions of the device Tiger Products Co., Ltd NH TS100-135A - which should help us in our first steps of using Tiger Products Co., Ltd NH TS100-135A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tiger Products Co., Ltd NH TS100-135A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tiger Products Co., Ltd NH TS100-135A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tiger Products Co., Ltd NH TS100-135A?

Use the form below

If you did not solve your problem by using a manual Tiger Products Co., Ltd NH TS100-135A, ask a question using the form below. If a user had a similar problem with Tiger Products Co., Ltd NH TS100-135A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)