-
Tiger Products Co., Ltd M105X/S - page 1
P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SIDE ROT AR Y ASSEMBLIES KUBOT A M105X/S CAB / WOC 06070001 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 07/12/2010 ...
-
Tiger Products Co., Ltd M105X/S - page 2
T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize ...
-
Tiger Products Co., Ltd M105X/S - page 3
FORW ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . W e recommend that yo ...
-
Tiger Products Co., Ltd M105X/S - page 4
T ABLE OF CONTENTS SAFETY _____________________________________________ 1-1 Safety Information__________________________________ 1-2 ASSEMBL Y / MOUNTING SECTION _______________________ 2-1 OPERA TION SECTION _________________________________ 3-1 MAINTENANCE SECTION ______________________________ 4-1 P ARTS SECTION _________________________________ ...
-
Tiger Products Co., Ltd M105X/S - page 5
SAFETY SECTION ...
-
Tiger Products Co., Ltd M105X/S - page 6
Side Rtry Safety Section 1-2 SAFETY SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VER Y SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in M ...
-
Tiger Products Co., Ltd M105X/S - page 7
Side Rtry Safety Section 1-3 SAFETY SAFETY ! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) PELIGRO! LEA EL INSTRUCTIVO! DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Message ...
-
Tiger Products Co., Ltd M105X/S - page 8
Side Rtry Safety Section 1-4 SAFETY SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the Tractor while the tractor is moving. Mount the Tractor ...
-
Tiger Products Co., Ltd M105X/S - page 9
Side Rtry Safety Section 1-5 SAFETY SAFETY WARNING! The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment. (SG-16) WARNING! T ransport only at safe speeds. Serious accident s and injuries ca ...
-
Tiger Products Co., Ltd M105X/S - page 10
Side Rtry Safety Section 1-6 SAFETY SAFETY WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good ...
-
Tiger Products Co., Ltd M105X/S - page 11
Side Rtry Safety Section 1-7 SAFETY SAFETY CAUTION! On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5) DANGER! NEVER use drugs or alcohol immediately before or whi ...
-
Tiger Products Co., Ltd M105X/S - page 12
Side Rtry Safety Section 1-8 SAFETY SAFETY DANGER! The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities. To reduce ...
-
Tiger Products Co., Ltd M105X/S - page 13
Side Rtry Safety Section 1-9 SAFETY SAFETY DANGER! Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working ...
-
Tiger Products Co., Ltd M105X/S - page 14
Side Rtry Safety Section 1-10 SAFETY SAFETY WARNING! Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower ...
-
Tiger Products Co., Ltd M105X/S - page 15
Side Rtry Safety Section 1-11 SAFETY SAFETY WARNING! The rotating parts of this machine continue to rotate even after the Tractor has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased. (SBM-5) “Wait a minute...Sav ...
-
Tiger Products Co., Ltd M105X/S - page 16
Side Rtry Safety Section 1-12 SAFETY SAFETY ...
-
Tiger Products Co., Ltd M105X/S - page 17
Side Rtry Safety Section 1-13 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 1 22839 1 INSTRUCT Don Not Lubricate With Automatic Grease Gun 2 22840 1 WARNING Foreign Objects Contacted 3 24028 1 WARNING Inspect Rear Flap 4 31522 1 LOGO TIGER MOWERS 5 31523 3 LOGO TIGER MOWERS 6 42350 1 DANGER Cuttershaft Direction 7 33743 1 INSTRUCT Mowing Safet Tips ...
-
Tiger Products Co., Ltd M105X/S - page 18
Side Rtry Safety Section 1-14 SAFETY SAFETY 10"X5.5" 31522 MOWER DECK 18.25"X10" 31523 HYDRAULIC T ANK 22840 INSIDE OF CAB 22839 MOWER DECK P AR T NO. LOCA TION 24028 MOWER DECK ...
-
Tiger Products Co., Ltd M105X/S - page 19
Side Rtry Safety Section 1-15 SAFETY SAFETY 5 42399 MOWER DECK 42400 MOWER DECK 33743 INSIDE OF CAB 42350 MOWER DECK P AR T NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 20
Side Rtry Safety Section 1-16 SAFETY SAFETY 29-6T3221 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB 6T3219 INSIDE OF CAB 6T3217 MOWER DECK P AR T NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 21
Side Rtry Safety Section 1-17 SAFETY SAFETY 6T3236 MOWER DECK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 INSIDE OF CAB P AR T NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 22
Side Rtry Safety Section 1-18 SAFETY SAFETY 16 6T3236 MOWER DECK HYDRAULIC T ANK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 HYDRAULIC T ANK P AR T NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 23
Side Rtry Safety Section 1-19 SAFETY SAFETY TB101 1 MOWER DECK 02962764 MOWER DECK DRAFT BEAM 6T3261 MOWER DECK 6T3249A MOWER DECK P ART NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 24
Side Rtry Safety Section 1-20 SAFETY SAFETY 02967827 CAB FENDER 02965262 DRAFT BEAM P AR T NO. LOCA TION ...
-
Tiger Products Co., Ltd M105X/S - page 25
Side Rtry Safety Section 1-21 SAFETY SAFETY 00756059 MOWER DECK 34852 HYDRAULIC T ANK ...
-
Tiger Products Co., Ltd M105X/S - page 26
Side Rtry Safety Section 1-22 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 Round Manual Canister 33997 1 Decal, Sheet, Manual Canister 2 * Decal 3 * Decal 4 * Decal 5 * AVAIL Specification Product Manual 6 33753 1 EMI Safety Manual 7 34296 1 Front Adhesive Pad 8 34297 1 Rear Adhesive Pad 9 6T1823 4 ...
-
Tiger Products Co., Ltd M105X/S - page 27
Side Rtry Safety Section 1-23 SAFETY SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations U.S ...
-
Tiger Products Co., Ltd M105X/S - page 28
Side Rtry Safety Section 1-24 SAFETY SAFETY ...
-
Tiger Products Co., Ltd M105X/S - page 29
ASSEMBL Y SECTION Assembly Section 2-1 ...
-
Tiger Products Co., Ltd M105X/S - page 30
Assembly Section 2-2 ASSEMBL Y CRANKSHAFT ADAPTER If necessary remove the four capscrews from the crankshaf t pulley . Then inst all the crankshaft adapter plate and adapter to the pulley with capscrews and lockwashers as shown in the parts section. Before attempting to mount your Tiger mower , it is import ant to read an underst and all of the Saf ...
-
Tiger Products Co., Ltd M105X/S - page 31
Assembly Section 2-3 ASSEMBL Y AXLE BRACE INST ALLA TION With the tractor on jack-stands, remove the existing hardware and the three point links on the rear axle where the axle braces will be mounted. Use a hoist to raise the axle braces to the correctly matching mounting holes on the rear axle and the main frame. Use the existing hardware to attac ...
-
Tiger Products Co., Ltd M105X/S - page 32
Assembly Section 2-4 ASSEMBL Y BUMPER HYDRAULIC T ANK INST ALLA TION Install all fittings and tubes into tank and tank filter as shown in the parts section illustration. Insert tank sight glass on the inner right side of the tank. Install the temperature sensor (optional), or pipe plug into side of the tank. Attach the large mounting brackets on th ...
-
Tiger Products Co., Ltd M105X/S - page 33
Assembly Section 2-5 ASSEMBL Y FILLING HYDRAULIC RESERVOIR Refer to the maintenance section for filling specifications and hydraulic oil requirements. NOTE: Starting or running your Tiger mower before filling reservoir will cause serious damage to hydraulic pump. ...
-
Tiger Products Co., Ltd M105X/S - page 34
Assembly Section 2-6 ASSEMBL Y CABLE CONTROL MOUNTING BRACKET Preassemble the cable control boxes to the control mounting bracket as shown in the parts section. Use the image below for positioning the cable control bracket. Position the support bracket on the floor as a template. The upper right hole of the bracket is 2-1/2” from the right edge o ...
-
Tiger Products Co., Ltd M105X/S - page 35
Assembly Section 2-7 ASSEMBL Y FRONT STEERING CONSOLE - CUT HOLE TO ACCESS POWER SOURCE FOR SWITCH BOX CABLE SWITCH BOX WIRING Refer to the parts section for wiring diagram to hook up the switch box. Cover the four wires from the switch box with plastic wire wrap provided. Route the wires, that tap into the tractors power , from the switch box to t ...
-
Tiger Products Co., Ltd M105X/S - page 36
Assembly Section 2-8 ASSEMBL Y HUSCO V AL VE MOUNTING Match the holes on the valve to the holes on the valve plate. The holes on the plate for the cables should be on your right. Always start by matching the mounting holes on the Husco valve to the two mounting holes closest to you on the plate. There will be two more holes on the plate to match th ...
-
Tiger Products Co., Ltd M105X/S - page 37
Assembly Section 2-9 ASSEMBL Y POL YCARBONA TE SAFETY WINDOWS NOTE: Installing a boom mower requires that all of the right side windows be replaced with polycarbonate. Install the safety windows after all of the cab wiring and mounting is done; and before the boom arm is mounted. Locate all the hardware in the Parts Section on the Safety Screen pag ...
-
Tiger Products Co., Ltd M105X/S - page 38
Assembly Section 2-10 ASSEMBL Y INST ALLING O-RING FITTINGS Installing straight, 45° and 90° O-rings requires that the O-ring and washer (A) be up against the swivel body (B). Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set direction with a wrench and turn the O-r ...
-
Tiger Products Co., Ltd M105X/S - page 39
Assembly Section 2-11 ASSEMBL Y WEA THER-P ACK/METRI-P ACK ASSEMBL Y These instructions apply to both Weather-Pack and Metri-pack connectors. NOTE: Use the specific tool for the type of connector you are assembling. 1. Apply seal to cable, before stripping 2. Align seal with cable insulation. 3. Put terminal in crimping tool, then 4. Crimp and visu ...
-
Tiger Products Co., Ltd M105X/S - page 40
Assembly Section 2-12 ASSEMBL Y DRAFT BEAM MOUNTING Pull the inboard cylinder piston rod down to the extreme extended position. Slide the draft beam under the cylinder , and align clevis hole with draft beam hole nearest to the tractor . Install pin and secure with rollpin. Using inboard cylinder as a pivot point, slide draft beam under tractor and ...
-
Tiger Products Co., Ltd M105X/S - page 41
Assembly Section 2-13 ASSEMBL Y TRA VEL LOCK MOUNTING Install the travel lock bracket with pin and clip on the draft beam. Slide the draft beam and align the travel lock bracket hole with the mounting hole on the main frame. Install the cap screw , lockwasher and hex nut as shown in the picture. Raise the deck/flail to it’s upright position (Deck ...
-
Tiger Products Co., Ltd M105X/S - page 42
Assembly Section 2-14 ASSEMBL Y Slide other end of pivot arm with short distance between the cut-out and the end of the pivot arm, into the cylinder clevis. Next, line up the holes of the left and right lift linkage arms outside of the cylinder clevis holes. Connect with linkage pin, shims (as required), boss, cap-screw , lock-washer and hex nut as ...
-
Tiger Products Co., Ltd M105X/S - page 43
Assembly Section 2-15 ASSEMBL Y DECK / MOTOR FEEDLINE Install the 1” hose with the 90 degree flange on the front side of the motor to the inside upper oil port of the solenoid valve. Secure to motor with flange kit, and install swivel fittings on the other end. Install the other 1” hose with the 60 degree flange on the back side of the motor to ...
-
Tiger Products Co., Ltd M105X/S - page 44
Assembly Section 2-16 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book. The decals are to ...
-
Tiger Products Co., Ltd M105X/S - page 45
OPERA TION SECTION Operation Section 3-1 ...
-
Tiger Products Co., Ltd M105X/S - page 46
Side Rtry Operation Section 3-2 OPERA TION Safety is of primary importance to the owner / operator and to the manufacturer . The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the messages will be repeated throughout the manual. The owne ...
-
Tiger Products Co., Ltd M105X/S - page 47
Side Rtry Operation Section 3-3 OPERA TION ST ARTING TRACT OR AND MOWER Check the operators manual received from the tractor manufacturer , for their recommendation and procedures pertaining to your particular make and model. When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow ...
-
Tiger Products Co., Ltd M105X/S - page 48
Side Rtry Operation Section 3-4 OPERA TION The rear mower height is controlled with the 3-point hitch control lever . Follow the instructions for this control is the tractor operators manual. The tilt of the rear mower is controlled with the third spool if the lift valve and is coordinated as shown above. The side and rear mower positions may optio ...
-
Tiger Products Co., Ltd M105X/S - page 49
Side Rtry Operation Section 3-5 OPERA TION When cutting tall shrubs or small trees (maximum recommended size of material to be cut is 2” diameter) begin each pass at the top of the material and work down with each consecutive pass. Use a low speed to allow the cutting blades time to mulch as well as cut the foliage. When the initial pass has been ...
-
Tiger Products Co., Ltd M105X/S - page 50
Side Rtry Operation Section 3-6 OPERA TION TRANSPORTING MOWER T ransporting under the units own power: When transporting between job sites or between cutting passes, the following procedure should be followed: Shut off the power to the cutting head(s) and allow all motion to come to a complete stop. Raise the draft beam to it’s highest position. ...
-
Tiger Products Co., Ltd M105X/S - page 51
Side Rtry Operation Section 3-7 OPERA TION Next, switch the hose ends and reconnect to form two separate closed loops, see diagram below . Disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. Remove the keeper bolt and draft beam outer pivot pin. Separate the mower head from the tractor . Now r ...
-
Tiger Products Co., Ltd M105X/S - page 52
Side Rtry Operation Section 3-8 OPERA TION INSPECTION SHEETS ...
-
Tiger Products Co., Ltd M105X/S - page 53
Side Rtry Operation Section 3-9 OPERA TION Rotary Mower PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is of f, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mo ...
-
Tiger Products Co., Ltd M105X/S - page 54
Side Rtry Operation Section 3-10 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mower ...
-
Tiger Products Co., Ltd M105X/S - page 55
Side Rtry Operation Section 3-11 OPERA TION FRONT END LOADER PRE-OPERA TION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Load ...
-
Tiger Products Co., Ltd M105X/S - page 56
Side Rtry Operation Section 3-12 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loader ...
-
Tiger Products Co., Ltd M105X/S - page 57
MAINTENANCE SECTION Maintenance Section 4-1 ...
-
Tiger Products Co., Ltd M105X/S - page 58
Maintenance Section 4-2 MAINTENANCE T iger Mowers are designed for high performance and rugged durability , yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower . Regular maintenance at the intervals mentioned will result in the maximum efficiency and long life of t ...
-
Tiger Products Co., Ltd M105X/S - page 59
Maintenance Section 4-3 MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. This symbol indicates a point that needs to be greased at an interval noted in the section below . Refer to the Detailed Mainten ...
-
Tiger Products Co., Ltd M105X/S - page 60
Maintenance Section 4-4 MAINTENANCE WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly In-Line High Pressure Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly MONTHL Y OR EVER Y 150 HO ...
-
Tiger Products Co., Ltd M105X/S - page 61
Maintenance Section 4-5 MAINTENANCE SYMPTOMS CAUSE REMEDY Oil T emperature rises 1. Low oil level 1. Bring oil to proper level above 200 deg. F 2. Kinked/blocked hoses 2. Inspect / Repair / Replace 3. Worn pump / motor 3. Disable and repair Mower will not start 1. Blown fuse 1. Check fuse between mower or run switch and ignition / replace 2. Ball v ...
-
Tiger Products Co., Ltd M105X/S - page 62
Maintenance Section 4-6 MAINTENANCE Motor will not work 1. Excessive wear 1. Disassemble and repair . on internal parts NOTE: If flow meter is available, check pressure and flow volume for all suspected hydraulic problems. If the solution to your problem cannot be found in this section, call the T echnical Service representative at the number shown ...
-
Tiger Products Co., Ltd M105X/S - page 63
Maintenance Section 4-7 MAINTENANCE T ORQUE SPECIFICA TIONS * These are intended to be general specifications. See tractor operators or service manual for exact specifications for your unit. ...
-
Tiger Products Co., Ltd M105X/S - page 64
Maintenance Section 4-8 MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General Specification Recomended Mobil Lubricant Tractor Hydraulics Reservoir JD-20C Mobilfluid 424 MF M1 135,M1 141 FNHM2C134D (FNH201) Mower Hydraulics Reservoir Cold T emperatures 0 F S t art-Up ISO 46 Anti-Wear - Low T emp Mobil DTE 15M Normal T emperature ...
-
Tiger Products Co., Ltd M105X/S - page 65
Maintenance Section 4-9 MAINTENANCE POL YCARBONA TE CARE & MAINTENANCE The proprietary UV and Abrasion Resistant surface coating on SHIELDS ® SUPERCOA TED ™ polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life. T iger Corp. polycarbonate is ...
-
Tiger Products Co., Ltd M105X/S - page 66
Maintenance Section 4-10 MAINTENANCE RECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVIORS When filling or checking the oil level, the unit should be parked on a level surface, shut “ OFF ”, and allowed sufficient time to cool to ambient temperature. Use caution when removing the pressurized breather . Do not place face over opening when re ...
-
Tiger Products Co., Ltd M105X/S - page 67
Maintenance Section 4-11 MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut down and de-pressurized. Locate High Pressure Filter housing. Confirm that the element that is about to be installed matches the element p/n on the filter model tag. Example: V3.0510-06 (world line 100, HD049 m ...
-
Tiger Products Co., Ltd M105X/S - page 68
Maintenance Section 4-12 MAINTENANCE GREASING INNER AND OUTER DRAFT BEAM PIVOT POINTS Locate the grease zerks on the inner and outer draft beam pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into each zerk until grease protrudes from joints. Grease all pivots daily or every 8 hours of service ...
-
Tiger Products Co., Ltd M105X/S - page 69
Maintenance Section 4-13 MAINTENANCE With the cutter head lowered, locate the grease zerks on the linkage and pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications until it protrudes from the ends. With the cutter head in this position it is also possible to grease the draft beam cylinder anchors an ...
-
Tiger Products Co., Ltd M105X/S - page 70
Maintenance Section 4-14 MAINTENANCE GREASING PUMP DRIVE SHAFT COUPLER: With engine stopped, ensure drive shaft alignment by grasping coupler and sliding back and forth. Coupler should slide freely with approximately 1/8” of end play . If coupler does not slide freely , inspect for loose pump mount bolts, or damaged or loose crank shaft adapter . ...
-
Tiger Products Co., Ltd M105X/S - page 71
Maintenance Section 4-15 MAINTENANCE BALL V AL VES The ball valve at the hydraulic reservoir may need to be closed during certain maintenance or repair procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with valve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .T .O. ! Failure to do so may result in component failure! ADJUS ...
-
Tiger Products Co., Ltd M105X/S - page 72
Maintenance Section 4-16 MAINTENANCE GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject T iger S pindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal. Lubricate spindle weekly or every 40 hours of use. TIGHTENING SPINDLE BOL TS The spindle mounting b ...
-
Tiger Products Co., Ltd M105X/S - page 73
Maintenance Section 4-17 MAINTENANCE GREASING MOTOR SPLINE T O SPINDLE SPLINE Locate motor spline and spindle spline on the mower deck. Grease splines with Mobil moly 52. Use about 4 ounces of grease. Change grease yearly or every 500 hours. ...
-
Tiger Products Co., Ltd M105X/S - page 74
Maintenance Section 4-18 MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1 – Be sure you have a complete matching set of new knives for replacement. 2 – Remove knives and inspect holes for damage. Also watch for cracks in the disk around the holes. 3 – Lube threads with anti-seize, motor oil or grease. Install bolt through knife and disk from bottom s ...
-
Tiger Products Co., Ltd M105X/S - page 75
Maintenance Section 4-19 MAINTENANCE REPLACEMENT OF ROT AR Y DISK Failure to follow the following warnings and instructions may result in serious injury or damage to the equipment or property! The bolts that attach the knife mounting disk to the spindle must be grade 8. These 5/8 inch bolts are to be torqued to 204 dry or 184 oiled ft. lbs. A threa ...
-
Tiger Products Co., Ltd M105X/S - page 76
Maintenance Section 4-20 MAINTENANCE HEA VY DUTY SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT W ARNING! A press MUST be used to inst all bearing cups, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged. NOTE: The grease zerk and gussets are located on the top side of t ...
-
Tiger Products Co., Ltd M105X/S - page 77
Maintenance Section 4-21 MAINTENANCE BEARING INST ALLA TION 1 – Press upper bearing cup into the spindle housing. 2 – T urn the spindle housing over and press in the lower bearing cup. 3 – Place the lower bearing cone in the bearing cup. Next press the seal into the spindle housing. The inner lip of the seal must be DOWN, towards the bearing, ...
-
Tiger Products Co., Ltd M105X/S - page 78
Maintenance Section 4-22 MAINTENANCE BEARING ADJUSTMENT 1 – Clamp the bottom end of the spindle securely in a vise so the spindle housing turns freely . 2 – Position a magnetic base dial indicator on the outer diameter of the spindle housing. Locate the end of the dial indicator against the flat end of the spindle shaft. The dial indicator will ...
-
Tiger Products Co., Ltd M105X/S - page 79
Maintenance Section 4-23 MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operators manual. ______ Pump Drive Shaft: Check for end play in drive shaft / coupler and lubricate at zerks. ______ Crankshaft adapter: If equipped wi ...
-
Tiger Products Co., Ltd M105X/S - page 80
Maintenance Section 4-24 MAINTENANCE ...
-
Tiger Products Co., Ltd M105X/S - page 81
P ARTS SECTION SIDE ROT AR Y KUBOT A M105X Parts Section 5-1 ...
-
Tiger Products Co., Ltd M105X/S - page 82
Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locat ...
-
Tiger Products Co., Ltd M105X/S - page 83
Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION ASSEMBL Y P AG E TRACTOR SPECIFIC P ARTS: TRACTOR MNT . KIT - MAIN FRAME M105X 06101300 5-4 TRACTOR MOUNT KIT - HYDRAULICS M105X 06101300 5-6 COMBO DRAFT BEAM 5-8 2SP HUSCO CONTROLS - KUBOT A M105X 5-10 2SP HUSCO LIFT V AL VE - COMBO 06101302 5-12 2SP HUSCO LIFT V AL VE - CABLE 06101312 5- ...
-
Tiger Products Co., Ltd M105X/S - page 84
Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME M105X 5-22-06 ...
-
Tiger Products Co., Ltd M105X/S - page 85
Parts Section 5-5 TRACTOR MOUNT KIT - MAIN FRAME M105X ITEM PART NO. QTY. DESCRIPTION 1 06300043 1 MNFRM,KUB,M105X 2 06300044 1 AXL BRC,LH,KUB,M105X 3 06300045 1 AXL BRC,RH,KUB,M105X 4 23152 1 PUMP ,P350-1 3/4 GEAR 5 06380026 1 PUMP MNT ,KUB,M105S 6 06510083 1 V A L VE,BRAKE,SOL,3000PSI,METRI 34666 * T ANK,RES,BUMP ,BLANK,CPL T ,ASSY 7 33695 1 T AN ...
-
Tiger Products Co., Ltd M105X/S - page 86
Parts Section 5-6 TRACTOR MOUNT KIT - HYDRAULICS M105X 5-24-06 ...
-
Tiger Products Co., Ltd M105X/S - page 87
Parts Section 5-7 TRACTOR MOUNT KIT - HYDRAULICS M105X ITEM PART NO. QTY. DESCRIPTION 1 33695 1 T ANK,RES,BUMPER,BLANK 2 35269 1 F IL TER ASSY ,IN-T ANK,JIC,10MIC 3 06380026 1 PUMP MNT ,KUB,M105S 4 23152 1 PUMP ,P350-1 3/4 GEAR 5 06510083 1 V A L VE,BRAKE,SOL,3000PSI,METRI 6 TF4852 2 K I T ,FLANGE,#20 7 33554 2 ELBOW ,1MORBX1MJIC,45 8 33555 2 ADAPT ...
-
Tiger Products Co., Ltd M105X/S - page 88
Parts Section 5-8 COMBO DRAFT BEAM ...
-
Tiger Products Co., Ltd M105X/S - page 89
Parts Section 5-9 COMBO DRAFT BEAM ITEM P ART NO. QTY . DESCRIPTION 1 32143 1 BEAM,DRAFT ,JD5520-25 2 6T0151R 1 HYD. CYLINDER 3” X 10” 3 32215 1 HYD. CYLINDER 3” X 12” 4 TF4500A 1 PIVOT ARM 5 TF4507B 1 RIGHT LINKAGE ARM 6 TF4506B 1 LEFT LINKAGE ARM 7 30126B 2 PIN,DRAFT BEAM 8 6T3001 1 PIN, BEAM PIVOT 9 TF4519 2 PIN, LINKAGE 10 6T3003D 3 PIN ...
-
Tiger Products Co., Ltd M105X/S - page 90
Parts Section 5-10 2 SPOOL HUSCO CONTROLS - KUBOT A M105X 4-27-06 ...
-
Tiger Products Co., Ltd M105X/S - page 91
Parts Section 5-11 2 SPOOL HUSCO CONTROLS - KUBOT A M105X ITEM P ART NO. QTY . DESCRIPTION 1 6T1251 2 CBL CTRL BOX,180 DEG 2 21542 3 CAPSCREW ,1/4 X 4 NC 3 21525 3 HEX NUT ,1/4 NC 4 21986 3 LOCKWASHER,1/4 5 06510102 1 SWITCHBOX,SIDE,GND 6 34496 1 BRKT ,SWITCHBOX,UNI 7 32359 2 SCREW ,MACHINE,8-32X3/4 8 34508 2 WASHER,FENDER,#10 9 6T3952 2 HEX NUT ,8 ...
-
Tiger Products Co., Ltd M105X/S - page 92
Parts Section 5-12 2SP HUSCO LIFT V AL VE - COMBO 4-27-06 ...
-
Tiger Products Co., Ltd M105X/S - page 93
Parts Section 5-13 2SP HUSCO LIFT V AL VE - COMBO ITEM PART NO. QTY. DESCRIPTION 1 06340023 1 V A L V E MN T ,RH,KUB,M105X 2 06340024 1 V A L V E M N T ,LH,KUB,M105X 3 21631 10 CAPSCREW ,3/8 X 1-1/4 NC 4 21627 12 NYLOCK NUT ,3/8 NC 5 22016 14 F L A T W ASHER,3/8 6 06430044 1 BRACE,VL V MNT ,KUB 7 21625 1 HEX NUT ,3/8 NC 8 34622 1 P L A TE,V A L VE, ...
-
Tiger Products Co., Ltd M105X/S - page 94
Parts Section 5-14 2SP HUSCO LIFT V AL VE - CABLE ...
-
Tiger Products Co., Ltd M105X/S - page 95
Parts Section 5-15 2SP HUSCO LIFT V AL VE - CABLE ITEM PART NO. QTY. DESCRIPTION 1 06340023 1 V A L V E MN T ,RH,KUB,M105X 2 06340024 1 V A L V E M N T ,LH,KUB,M105X 3 21631 10 CAPSCREW ,3/8 X 1-1/4 NC 4 21627 12 NYLOCK NUT ,3/8 NC 5 22016 14 F L A T W ASHER,3/8 6 06430044 1 BRACE,VL V MNT ,KUB 7 21625 1 HEX NUT ,3/8 NC 8 34622 1 P L A TE,V A L VE, ...
-
Tiger Products Co., Ltd M105X/S - page 96
Parts Section 5-16 2SP HUSCO V AL VE - POWER BEYOND (30801) ...
-
Tiger Products Co., Ltd M105X/S - page 97
Parts Section 5-17 2SP HUSCO V AL VE - POWER BEYOND (30801) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 4 06502091 1 V AL VE SECTION (DOUBLE ACTING , CENTER SPRING) (NO AUX V AL VE PORTS) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -OFF PLUG ...
-
Tiger Products Co., Ltd M105X/S - page 98
Parts Section 5-18 2SP HUSCO V AL VE - POWER BEYOND (31752) ...
-
Tiger Products Co., Ltd M105X/S - page 99
Parts Section 5-19 2SP HUSCO V AL VE - POWER BEYOND (31752) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 4 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -OFF PLUG 8 TB1017E 1 RELIEF V A ...
-
Tiger Products Co., Ltd M105X/S - page 100
Parts Section 5-20 SAFETY SCREEN - KUBOT A M105X ...
-
Tiger Products Co., Ltd M105X/S - page 101
Parts Section 5-21 SAFETY SCREEN - KUBOT A M105X ITEM PART NO. QTY. DESCRIPTION 1 06490023 1 POL YCARB,FRMD,KUB,M105X,RH 2 31965 20’ TRIM SEAL,3/8 CLIP X 3/4 OD 3 06520040 3 BRKT ,JD,POL Y ,RET AIN 4 06410391 1 MN T ,POL Y ,KUB 5 06410392 1 M N T ,SM,POL Y ,KUB 6 06537000 6 WASHER,NEOPRENE,.25x1x.38 7 06537001 6 WASHER,RUBBERIZED,.25,CONICAL 8 21 ...
-
Tiger Products Co., Ltd M105X/S - page 102
Parts Section 5-22 OPTIONAL PUMP GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 21831 4 CAPSCREW - 3/4 X 1 3/4 3 21993 4 LOCKWASHER - 3/4 4 21825 4 HEX NUT - 3/4 1 1-20-01 ...
-
Tiger Products Co., Ltd M105X/S - page 103
Parts Section 5-23 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 32737 1 UNIVERSAL GRILL GUARD 3 21833 4 CAPSCREW - 3/4 X 2 1/4 4 22021 2 FLATWASHER - 3/4 5 21993 4 LOCKWASHER - 3/4 6 21825 4 HEX NUT - 3/4 1 1-20-01 ...
-
Tiger Products Co., Ltd M105X/S - page 104
Parts Section 5-24 ITEM PART NO. QTY. DESCRIPTION 1 06370048 1 FUEL T ANK,RH,KUB,M105X 2 06370049 2 T ANK STRAP ,KUB,M105X 3 06503061 1 ADAPTER,1 1/4NPTx1 1/4BARB 4 06503063 1 ELBOW ,3/8NPTx3/8BARB 5 06503092 1 ELBOW ,1/4NPTx1/4BARB 6 22016 4 F L A TW ASHER,3/8 7 21627 4 NYLOCK NUT ,3/8 NC 8 6T3200 2 SPLIT HOSE 9 * 5 EXISTING HARDWARE 1 0 * 1 EXIST ...
-
Tiger Products Co., Ltd M105X/S - page 105
Parts Section 5-25 SWITCH BOX SCHEMA TIC ...
-
Tiger Products Co., Ltd M105X/S - page 106
Parts Section 5-26 SOLENOID BRAKE V A VLE ASSEMBL Y ITEM PART NO. QTY. DESCRIPTION 1 34092 1 BRAKE VALVE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) ...
-
Tiger Products Co., Ltd M105X/S - page 107
Parts Section 5-27 SOLENOID BRAKE V A L VE HYDRAULIC SCHEMA TIC BRAKE V AL VE TROUBLESHOOTING F AILURE MODE: CHECK STEPS - MOWER WILL NOT ST AR T - system pressure is low (engine not lugging). 1 thru 6 - MOWER WILL NOT ST AR T - system pressure is high (engine lugging). “MR” port will be high pressure. 7 - MOWER WILL NOT ROT A TE A T FULL SPEED ...
-
Tiger Products Co., Ltd M105X/S - page 108
Parts Section 5-28 ...
-
Tiger Products Co., Ltd M105X/S - page 109
Side Rotary Common Section 6 - 1 SIDE ROT AR YCOMMON SECTION COMMON P ARTS SECTION ...
-
Tiger Products Co., Ltd M105X/S - page 110
Side Rotary Common Section 6 - 2 T ABLE OF CONTENTS SECTION ASSEMBL Y P AGE CABLE LIFT ASSEMBL Y 6-4 COMBO DRAFT BEAM 6-6 60” SIDE CABLE ROT ARY MOWER ASSEMBL Y 6-8 72” SIDE CABLE ROT AR Y MOWER ASSEMBL Y 6-10 60” SIDE COMBO RTR Y MOWER ASSEMBL Y 6-12 60” SIDE ROT AR Y MOWER 6-14 60” SPINDLE AND SP ACER 6-16 72” SIDE COMBO ROT ARY MOWER ...
-
Tiger Products Co., Ltd M105X/S - page 111
Side Rotary Common Section 6 - 3 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are give ...
-
Tiger Products Co., Ltd M105X/S - page 112
Side Rotary Common Section 6 - 4 CABLE LIFT ASSEMBL Y 3-22-02 ...
-
Tiger Products Co., Ltd M105X/S - page 113
Side Rotary Common Section 6 - 5 CABLE LIFT ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 6T0103A 1 DRAFT BEAM (STD 25 LB, 45 3/8”) 6T0103E OP T . DRAFT BEAM (EXTENDED 6” 4WD) 6T0103L O PT . DRAFT BEAM (EXTENDED 15”) 6T0105 O P T . DRAFT BEAM (STD WITH TRA VEL LOCK) 6T0108 O P T . DRAFT BEAM (30 LB CHANNEL, 45 3/8”) 2 6T0150 1 CYLINDER 3” ...
-
Tiger Products Co., Ltd M105X/S - page 114
Side Rotary Common Section 6 - 6 COMBO DRAFT BEAM 3-22-02 ...
-
Tiger Products Co., Ltd M105X/S - page 115
Side Rotary Common Section 6 - 7 COMBO DRAFT BEAM ITEM P ART NO. QTY . DESCRIPTION 1 06350001 1 COMBO DRAFT BEAM - STD DTY ROT ARY 31063 O PT . COMBO DRAFT BEAM - HVY DTY ROT ARY 2 6T0151R 1 HYD. CYLINDER 3” X 10” 3 32215 1 HYD. CYLINDER 3” X 12” - STD DTY 25343 RE F HYD. CYLINDER 3” X 12” - HVY DTY 4 TF4500A 1 PIVOT ARM 5 TF4507B 1 RIG ...
-
Tiger Products Co., Ltd M105X/S - page 116
Side Rotary Common Section 6 - 8 60” SIDE CABLE ROT AR Y MOWER ...
-
Tiger Products Co., Ltd M105X/S - page 117
Side Rotary Common Section 6 - 9 60” SIDE CABLE ROT AR Y MOWER ITEM P ART NO. QTY . DESCRIPTION 1 32099 1 RT RY , 60" WELDMENT , 1/4" DECK 21225B 1 RTRY , 72” WELDMENT , 1/4” DECK 2 22592 1 FLAP , DEFLECT OR, TM60 3 6T0823 1 BAR, FLAP , TM60 4 6T0822 2 SHIM, MOTOR MOUNT , 14GA. (AS NEEDED) 5 6T0822A 2 SHIM, MOTOR MOUNT , 18 GA. (AS ...
-
Tiger Products Co., Ltd M105X/S - page 118
Side Rotary Common Section 6 - 10 72” SIDE CABLE ROT AR Y MOWER ...
-
Tiger Products Co., Ltd M105X/S - page 119
Side Rotary Common Section 6 - 11 72” SIDE CABLE ROT AR Y MOWER ITEM P ART NO. QTY . DESCRIPTION 1 21225B 1 RT R Y , 72” WELDMENT , 1/4” DECK 2 21295B 1 FLAP , DEFLECTOR, TM72 3 21242A 1 BAR, FLAP , TM72 4 6T0822 2 SHIM, MOTOR MOUNT , 14GA. (AS NEEDED) 5 6T0822A 2 SHIM, MOTOR MOUNT , 18 GA. (AS NEEDED) 6 6T1001 1 BRKT , MOTOR MTG , 60"SI ...
-
Tiger Products Co., Ltd M105X/S - page 120
Side Rotary Common Section 6 - 12 60” SIDE COMBO ROT AR Y MOWER ...
-
Tiger Products Co., Ltd M105X/S - page 121
Side Rotary Common Section 6 - 13 60” SIDE COMBO ROT AR Y MOWER ITEM P ART NO. QTY . DESCRIPTION 1 32617 1 RT RY , 60" DECK, COMBO - SDT DUTY 30188D 1 RT RY , 60” DECK, COMBO - HEA VY DUTY 2 31773 1 GAURD,CHAIN,FRONT ,SR60 3 6T1001 1 BRKT , MOTOR MTG , 60"SIDE RTRY 4 6T0820H 2 SKID SHOE, TM60, HEA VY DUTY 5 22592 1 FLAP , DEFLECT OR, ...
-
Tiger Products Co., Ltd M105X/S - page 122
Side Rotary Common Section 6 - 14 60” SIDE ROT AR Y MOWER 8/26/05 ...
-
Tiger Products Co., Ltd M105X/S - page 123
Side Rotary Common Section 6 - 15 60” SIDE ROT AR Y MOWER ITEM P A R T N O . QT Y . DESCRIPTION 1 34975 1 H E A VY DUTY GRASSKA T COMBO 06320005 1 S TD D U TY GRASSKA T COMBO 06320008 1 H E A V Y DUTY GRASSKA T CABLE 2 34980 1 SPINDLE ASSY ,TM 60" 3 06504016 1 CURRENT MOTOR,(M365-1 1/4" 14-SPLINE) 34981 1 ORIGINAL MOTOR,(M365-1 1/4" ...
-
Tiger Products Co., Ltd M105X/S - page 124
Side Rotary Common Section 6 - 16 60” SIDE ROT AR Y SPINDLE AND SP ACER ...
-
Tiger Products Co., Ltd M105X/S - page 125
Side Rotary Common Section 6 - 17 60” SIDE ROT AR Y SPINDLE AND SP ACER ITEM P A RT NO . QTY . DESCRIPTION 1 34975 1 H E A V Y DUTY GRASSKA T COMBO 06320005 1 STD DUTY GRASSKA T COMBO 06320008 1 H E A V Y DUTY GRASSKA T CABLE 2 34980 1 SPINDLE ASSY ,TM 60" 3 0632001 1 2 SP ACER,TSR,SPINDLE 4 06533004 8 F L A T W ASHER,1/2,SAE,GR 8 5 06530221 ...
-
Tiger Products Co., Ltd M105X/S - page 126
Side Rotary Common Section 6 - 18 72” SIDE COMBO ROT AR Y MOWER ...
-
Tiger Products Co., Ltd M105X/S - page 127
Side Rotary Common Section 6 - 19 72” SIDE COMBO ROT AR Y MOWER ITEM P ART NO. QTY . DESCRIPTION 1 34260 1 RT RY , 72" DECK, COMBO - SDT DUTY 31408A 1 RT RY , 72” DECK, COMBO - HEA VY DUTY 2 31931 1 GAURD,CHAIN,FRONT ,SR60 3 6T1001 1 BRKT , MOTOR MTG , 60"SIDE RTRY 4 21248 2 SKID SHOE, TM72 5 21295B 1 FLAP , DEFLECTOR, TM72 6 21242A 1 ...
-
Tiger Products Co., Ltd M105X/S - page 128
Side Rotary Common Section 6 - 20 TM72” MOTOR ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 06504018 1 MOTOR 2 TF4852 2 K I T ,FLANGE,#20 3 34943 2 ELBOW ,#20FLG x #16MJ 4 24724 1 ELBOW ,#16FJX x #16MJ45 5 06500444 1 HOSE,#16 x 141 6 06500445 1 HOSE,#16 x 145 ...
-
Tiger Products Co., Ltd M105X/S - page 129
Side Rotary Common Section 6 - 21 P AGE INTENSIONALL Y LEFT BLANK ...
-
Tiger Products Co., Ltd M105X/S - page 130
Side Rotary Common Section 6 - 22 CHAIN GUARDS ...
-
Tiger Products Co., Ltd M105X/S - page 131
Side Rotary Common Section 6 - 23 SIDE ROT AR Y CHAIN GUARDS 60” SIDE ROT AR Y ITEM P ART NO. QTY . DESCRIPTION 31773 STD. GAU RD,CHAIN,SR60,FRONT ASSY 1 31762 1 GUARD,CHAIN,TM60,FRONT 2 28407 12’ CABLE, 5/16”, BULK 3 22993 7 7 CHAIN, 5/16” GR30, 9 LINK ** 28408 4 U-BOL T , CABLE, 5/16” ** NOT SHOWN 72” SIDE ROT AR Y ITEM P ART NO. QTY ...
-
Tiger Products Co., Ltd M105X/S - page 132
Side Rotary Common Section 6 - 24 SIDE ROT AR Y CASTER WHEEL ASSEMBL Y ...
-
Tiger Products Co., Ltd M105X/S - page 133
Side Rotary Common Section 6 - 25 SIDE ROT AR Y CASTER WHEEL ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 25214C 1 FRAME,CASTER,WHL,TM60,W/O CG 2 22057C 1 SPINDLE, CASTER AXLE, ASSY 3 6T2617 2 BUSHING ,MACH,1-1/2IDX 2-1/4OD 4 28548 1 CASTER WHEEL, SOLID TIRE ** 22065 1 HUB ASSY , REAR ROT ARY ** 22066 1 H UB, CASTER (REAR ROT ARY) ** 22070 1 DUST C ...
-
Tiger Products Co., Ltd M105X/S - page 134
Side Rotary Common Section 6 - 26 RESER VOIR T ANK FIL TER ASSEMBL Y ...
-
Tiger Products Co., Ltd M105X/S - page 135
Side Rotary Common Section 6 - 27 RESER VOIR T ANK FIL TER ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 06505044 A V AI L F I L TER ASSY SAE 10 MICRON 1 28583 4 C A P SCREW ,8MMX25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 S E A L K I T 4 06505047 1 SPRING 5 06505048 1 B Y PAS S 6 35259 1 F IL TER,10 MIC,RETURN LINE 7 06505049 1 CAN/BODY ...
-
Tiger Products Co., Ltd M105X/S - page 136
Side Rotary Common Section 6 - 28 MOWER SPINDLE ASSEMBL Y - 6T1024H5 ...
-
Tiger Products Co., Ltd M105X/S - page 137
Side Rotary Common Section 6 - 29 MOWER SPINDLE ASSEMBL Y - 6T1024H5 ITEM P ART NO. QTY . DESCRIPTION 6T1024H5 A V A IL SPINDLE ASSEMBL Y COMPLETE 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT - THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT - THIN 5 6T1014 1 BEARING ADJUSTMENT SLEEVE 6 6T101 1 1 UPPER SEAL - SET OF 2 7 6T1012 1 B E ...
-
Tiger Products Co., Ltd M105X/S - page 138
Side Rotary Common Section 6 - 30 MOWER SPINDLE ASSEMBL Y - 34980 ...
-
Tiger Products Co., Ltd M105X/S - page 139
Side Rotary Common Section 6 - 31 MOWER SPINDLE ASSEMBL Y - 34980 ITEM P A RT NO . QTY . DESCRIPTION 1 34978 1 SPINDLE MOUNT 2 34979 1 SPINDLE,TM60",NEW 3 6T1013 1 BEARING CUP 4 6T1012 1 BEARING ,CONE 5 6T101 1 2 SEAL,UPPER (SET OF 2) 6 6T1014 1 SLEEVE,ADJ BEARING 7 6T1013H 1 BEARING CUP ,HD 8 6T1012H 1 BEARING ,CONE,HD 9 6T101 1H 1 SEAL,LOWER ...
-
Tiger Products Co., Ltd M105X/S - page 140
Side Rotary Common Section 6 - 32 HYDRAULIC LIFT CYLINDER ...
-
Tiger Products Co., Ltd M105X/S - page 141
Side Rotary Common Section 6 - 33 HYDRAULIC LIFT CYLINDER 3” X 12” CYLINDER # 32215 ITEM P ART NO. QTY . DESCRIPTION 1 6T0167 1 CYLINDER BUTT 2 6T0170 1 CYLINDER GLAND 3 6T0178 1 CLEVIS END 4 6T0204 1 CYLINDER TUBE 5 6T0203 1 PISTON ROD 6 6T0173 1 PISTON 7 6T0179 1 LOCKNUT 8 6T0205 1 TIE ROD ASY 6T0187 A V A IL SEAL KIT 9 2 O - RING 1 0 2 BACK ...
-
Tiger Products Co., Ltd M105X/S - page 142
Side Rotary Common Section 6 - 34 ROT AR Y KNIVES AND DISKS ITEM P ART NO. QTY . DESCRIPTION 1 34876 1 BLADE MOUNTING DISK 2 6T1023R 2 NYLOCK HEX NUT 1 1/8” 3 34878 2 S P ACER 4 34497 2 KNIFE MOUNTING BOL T 5 34685 2 KNIFE,60" HIGH SUCTION - ST ANDARD 5A 34684 2 K N I F E , 6 0 " - OPTIONAL 6 34682 2 KNIFE 72” - MOUNT ON 72” MOWER O ...
-
Tiger Products Co., Ltd M105X/S - page 143
Side Rotary Common Section 6 - 35 CASTER WHEEL ASSEMBL Y ITEM P ART NO. QT Y . DESCRIPTION 1 21459 1 SPINDLE, CASTER WHEEL AXLE 2 21987 5 LOCKWASHER, 5/16” 3 21575 5 HEX NUT , 5/16” 4 28548 5 CAPSCREW , 5/16” x 3/4”, NC 5 22697-1 1 RIM, OUTER/RR RTRY CASTER ASSY 6 21416 1 TIRE,SOLID,RR-RTRY 7 22696-1 1 RIM,REAR ROT ARY CASTER 8 22070 1 DUST ...
-
Tiger Products Co., Ltd M105X/S - page 144
Side Rotary Common Section 6 - 36 ROT AR Y MOT OR ...
-
Tiger Products Co., Ltd M105X/S - page 145
Side Rotary Common Section 6 - 37 ROT AR Y MOT OR ITEM P ART NO. QTY . DESCRIPTION 06504018 MOTOR 06504103 1 S E A L K I T 1 22790 1 HOUSING , SEC 2 06504088 1 HOUSING , SEC 3 06504062 1 HOUSING , GEAR 4 06504105 1 S E T , GEAR SHAFT 5 06504106 4 CAP SCREW 6 06504078 2 SCREW , DRIVE 7 06504092 1 K E Y 8 06504093 4 PIN, DOWEL 9 06504094 1 NAME PLA T ...
-
Tiger Products Co., Ltd M105X/S - page 146
Side Rotary Common Section 6 - 38 HYDRO PUMP & TSR MOTOR TSR MOTOR FRONT PUMP ...
-
Tiger Products Co., Ltd M105X/S - page 147
Side Rotary Common Section 6 - 39 HYDRO PUMP & TSR MOTOR FRONT HYDRAULIC PUMP ITEM P ART NO. QTY . DESCRIPTION 23152 A V A I L PUMP ASSEMBL Y 1 3/4” COMPLETE 1 22765 1 SEAL (INCLUDED IN SEAL KIT) 2 22766 1 SHAFT END COVER 3 22767 2 CHECK AND END COVER 4 22768 2 BUSHING 5 22769 2 CHANNEL SEAL (INCLUDED IN SEAL KIT) 6 22770 2 THRUST PLA TE (INC ...
-
Tiger Products Co., Ltd M105X/S - page 148
Side Rotary Common Section 6 - 40 SIDE COOLER ...
-
Tiger Products Co., Ltd M105X/S - page 149
Side Rotary Common Section 6 - 41 SIDE COOLER ITEM PART NO. QTY. DESCRIPTION 1 21530 10 CAPSCREW ,1/4 X1 NC 2 21986 10 LOCKWASHER,1/4 3 22014 10 F L A T W ASHER,1/4 4 35176 10 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 M N T ,COOLER,BUMPER T ANK,RH 7 06380007 1 M N T ,COOLER,BUMPER T ANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CAPSCR ...
-
Tiger Products Co., Ltd M105X/S - page 150
Side Rotary Common Section 6 - 42 2SP HUSCO - POWER BEYOND (30801) ...
-
Tiger Products Co., Ltd M105X/S - page 151
Side Rotary Common Section 6 - 43 2SP HUSCO - POWER BEYOND (30801) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 4 06502091 1 V AL VE SECTION (DOUBLE ACTING , CENTER SPRING) (NO AUX V AL VE PORTS) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -O ...
-
Tiger Products Co., Ltd M105X/S - page 152
Side Rotary Common Section 6 - 44 2 SP HUSCO - LOAD SENSE (31320) ...
-
Tiger Products Co., Ltd M105X/S - page 153
Side Rotary Common Section 6 - 45 2 SP HUSCO - LOAD SENSE (31320) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 N/A - N/A 8 6T4209 1 RE ...
-
Tiger Products Co., Ltd M105X/S - page 154
Side Rotary Common Section 6 - 46 2 SP HUSCO - LOAD SENSE (31321) ...
-
Tiger Products Co., Ltd M105X/S - page 155
Side Rotary Common Section 6 - 47 2 SP HUSCO - LOAD SENSE (31321) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF V AL VE, 360 PSI 7 N/A - N/A 8 6T ...
-
Tiger Products Co., Ltd M105X/S - page 156
Side Rotary Common Section 6 - 48 2SP HUSCO - POWER BEYOND (31752) ...
-
Tiger Products Co., Ltd M105X/S - page 157
Side Rotary Common Section 6 - 49 2SP HUSCO - POWER BEYOND (31752) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 4 TB1017P 1 V AL V E SECTION (SINGLE ACTING , SPRING DETENT) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -OFF PLUG 8 TB1017E 1 REL ...
-
Tiger Products Co., Ltd M105X/S - page 158
Side Rotary Common Section 6 - 50 2SP HUSCO - LOAD SENSE (06502040) ...
-
Tiger Products Co., Ltd M105X/S - page 159
Side Rotary Common Section 6 - 51 2SP HUSCO - LOAD SENSE (06502040) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V A L VE SECTION (DOUBLE ACTING , CENTER SPRING) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 ...
-
Tiger Products Co., Ltd M105X/S - page 160
Side Rotary Common Section 6 - 52 2SP HUSCO - LOAD SENSE (06502042) ...
-
Tiger Products Co., Ltd M105X/S - page 161
Side Rotary Common Section 6 - 53 2SP HUSCO - LOAD SENSE (06502042) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31600 1 V A L VE SECTION (DOUBLE ACTING , DETENT FLOA T) 4 31600 1 V A L VE SECTION (DOUBLE ACTING , DETENT FLOA T) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF V AL VE 3 ...
-
Tiger Products Co., Ltd M105X/S - page 162
Side Rotary Common Section 6 - 54 ITEM PART NO. QTY. DESCRIPTION 06502007 A V AI L V A L V E AS Y H IGH PRESSURE 06502008 A V AI L V ALVE A S Y LOW PRESSUTE 1 34689 1 SOLENOID COIL 2 06505026 1 SOLENOID 3 06502009 1 SOLENOID V AL VE KIT 4 6T391 1 1 SOLENOID SEAL KIT 5 6T3908 1 RELIEF PILOT 2150 PSI LOW PRESSURE 6 6T3910 1 RELIEF PILOT 3400 PSI HIGH ...
-
Tiger Products Co., Ltd M105X/S - page 163
Side Rotary Common Section 6 - 55 SOLENOID BRAKE V AL VE ASSEMBL Y ITEM PART NO. QTY. DESCRIPTION * 34115 AVAIL SOLENOID BRAKE VALVE ASSEMBLY - HIGH PRESSURE 1 34092 1 BRAKE VALVE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 5 34091 1 RELIEF VALVE, 2600 PSI 6 34689 1 ...
-
Tiger Products Co., Ltd M105X/S - page 164
Side Rotary Common Section 6 - 56 BRAKE V A L VE ASSEMBL Y W/ METRI P AK ITEM PART NO. QTY. DESCRIPTION 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34095 1 RELIEF VALVE, 3000 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI ...
-
Tiger Products Co., Ltd M105X/S - page 165
Side Rotary Common Section 6 - 57 SOLENOID BRAKE V A L VE HYDRAULIC SCHEMA TIC BRAKE V A L VE TROUBLESHOOTING F AILURE MODE: CHECK STEPS - MOWER WILL NOT ST ART - system pressure is low (engine not lugging). 1 thru 6 - MOWER WILL NOT ST AR T - system pressure is high (engine lugging). “MR” port will be high pressure. 7 - MOWER WILL NOT ROT A TE ...
-
Tiger Products Co., Ltd M105X/S - page 166
Side Rotary Common Section 6 - 58 TRA VEL LOCK LIFT BEAM ITEM PART NO. QTY. DESCRIPTION 1 6T0105 1 DRAFT BEAM (STD WITH TRA VEL LOCKS) 2 6T0106 1 T R AVE L LOCK BRACKET 3 6T0107 2 T R AV E L LOCK PINS 3/4” X 3 1/4” 4 6T3020 2 R - CLIP 5/32” 5 21833 1 CAPSCREW 3/4” X 2 1/4” 6 21825 1 HEX NUT 3/4” 7 21993 1 LOCK WASHER 3/4” 8 22021 1 F ...
-
Tiger Products Co., Ltd M105X/S - page 167
Side Rotary Common Section 6 - 59 SIDE MOWER TRA VEL LOCK (COMBO) ITEM PART NO. QTY. DESCRIPTION 1 R E F * COMBO DRAFT BEAM- REFER T O DRAFT BEAM P ARTS 2 6T0106 1 T R AVE L LOCK BRAKCET 3 6T0107 2 T R AV E L LOCK PIN (3/4” x 3-1/4”CAPPED) 4 6T3020 2 R-CLIP , 5/32” 5 21833 1 CAPSCREW , 3/4” x 2-1/4” NC 6 21825 1 HEX NUT , 3/4” NC 7 2199 ...
-
Tiger Products Co., Ltd M105X/S - page 168
Side Rotary Common Section 6 - 60 SWITCHBOX SER VICE P ARTS ITEM P / N QTY . DESCRIPTION 1 06514013 1 SWBX,ALUM,BLK,06510102 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 3381 1 1 SWITCH,MASTER/DECK FLOA T 4 6T3923 1 INDICT A TOR LIGHT ,ON,RED 5 06514014 1 BREAKER,10A,SWBX 6 34540 1 S T R A I N R E L I E F , 3 / 4 , B L A CK,NYLON 7 06550018 1 DECAL,SWTCHBX, ...
-
Tiger Products Co., Ltd M105X/S - page 169
Side Rotary Common Section 6 - 61 SWITCHBOX SCHEMA TIC ...
-
Tiger Products Co., Ltd M105X/S - page 170
Side Rotary Common Section 6 - 62 ...
-
Tiger Products Co., Ltd M105X/S - page 171
W ARRANTY SECTION Warranty Section 7-1 ...
-
Tiger Products Co., Ltd M105X/S - page 172
. ...
-
Tiger Products Co., Ltd M105X/S - page 173
W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the f ...
-
Tiger Products Co., Ltd M105X/S - page 174
ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an ...
-
Tiger Products Co., Ltd M105X/S - page 175
T O THE OWNER / OPERA TOR / DEALER T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health A ...
-
Tiger Products Co., Ltd M105X/S - page 176
Printed in USA © T iger Corporation ...
Do you have a question concerning Tiger Products Co., Ltd M105X/S?
Use the form below
If you did not solve your problem by using a manual Tiger Products Co., Ltd M105X/S, ask a question using the form below. If a user had a similar problem with Tiger Products Co., Ltd M105X/S it is likely that he will want to share the way to solve it.