English dropdown-ico

Manual Hoshizaki IM-500SAA

24 pages 1.76 mb
Download

Go to site of 24

Summary
  • Hoshizaki IM-500SAA - page 1

    AM SERVICE TRAINING Featuring the IM-500SAA 80047 9/10/13 ...

  • Hoshizaki IM-500SAA - page 2

    2 20mm All IM models have similar sequence of operation. This m anual is designed as a generic IM Training manual. The Hoshizaki IM series ice machine uses a horizontal evaporator design which forms a square cube shape with a small dimple. A standard 120-volt power cord (field supplied) provides the electrical connection. The unit is designed to op ...

  • Hoshizaki IM-500SAA - page 3

    3 The ABS water plate sprays water up into the evaporator cells to form the square IM cube. The moveable water pan asse mbly includes the water plate, reservoir pan, and pump m otor assembly. Tension springs connect two cam arms to the water plate assembly. An actuator motor rotates the cam arms to raise and lower the water pan during the ice makin ...

  • Hoshizaki IM-500SAA - page 4

    4 The horizontal evaporator and water distribution system are unique to the Hoshizaki IM series. The IM-500 makes ice on a horizontal evaporator and uses R-404a refrigerant. The IM-500SSA sequence of operation will be explained in the following pages. ...

  • Hoshizaki IM-500SAA - page 5

    5 The IM-500SAA unit uses a combination thermistor and control board to control the sequence of operation. SOFT START: When the toggle switch is placed in the “ON” position and the bin control calls for ice, the unit will begin in the soft start the display will say “on” and the hot gas valve will ope n after 30 seconds the initial harvest ...

  • Hoshizaki IM-500SAA - page 6

    6 As soon as the pan starts to open the defrost backup timer starts, if the thermistor mounted on the evaporator does not reach the defrost completion temperature before the tim er times out at 30 min. the display will show “E2” and the unit stops. (if the HGV does not open this could also give you an “E2” error) The harvest cycle is contro ...

  • Hoshizaki IM-500SAA - page 7

    7 WATER PAN CLOSES/FREEZE: When the water pan closes and the hall IC turns on the water valve opens to supply ice making wate r for a specific time. The supply time varies between startup, reset, and end of bin control cycle between partial flush and full drain. NOTE Full drain flush: After a freeze cycle ends the unit drains all remaining water ou ...

  • Hoshizaki IM-500SAA - page 8

    8 The IM-500SAA uses a mechanical bin control located on the right rear side of the ice drop zone. This control will open when ice pushes against the switch, if the switch stays open for more than 10 seconds the machine will start the bin control cycle, starts and the machine will shut down after the next defrost cycle. After the bin control stays ...

  • Hoshizaki IM-500SAA - page 9

    9 The control switch is marked “ICE- OFF-WASH” and is located on the upper right front of the unit. “OFF” – No power supplied to unit “ICE” – Starts the automatic Ice making process “WASH” – Power is supplied to water pump (this allows for cleaning and/or sanitizing “RESET”- If the reset is pushed after the unit is turned ...

  • Hoshizaki IM-500SAA - page 10

    10 CONTROL BOARD: A solid state board controls the IM operation. The control board is factory adjusted to produce consistent ice in all ambient conditions. “NO SEASONAL ADJUSTMENTS ARE REQUIRED” If it becomes necessary to insta ll a new IM-500SAA control board, part number P01873-01, the model code must be programmed into the board before the u ...

  • Hoshizaki IM-500SAA - page 11

    11 Preventative maintenance : Follow these steps to allow the unit to operate efficiently. 1. Clean the condenser once a year using a brush or vacuum. 2. Check and clean the inlet water valve screen as needed to assure proper water flow. 3. Clean and sanitize the water distribution system annually using the recommended clean er. (See below for deta ...

  • Hoshizaki IM-500SAA - page 12

    12 1) Dilute approximately 7.2 fl. oz. (214 ml) of recommended cleaner Hoshizaki “Scale Away” with 0.8 gal. (3.0 lit.) of water. 2) Turn off the power supply. 3) Remove all ice from the storage bin. 4) Remove the front panel. 5) Remove the screw, and then move the water tank drain pipe to the drain position. See Fig. 5. Use the screw to secure ...

  • Hoshizaki IM-500SAA - page 13

    13 14) Turn on the power supply to start the washing process. 15) Turn off the power supply after 30 minutes. 16) Open the icemaker water supply line shut-off valve. See Fig. 4. 17) Remove the front panel. 18) Move the control switch to the "ICE" position. 19) Replace the front panel. 20) Turn on the power supply for 3 minutes. The water ...

  • Hoshizaki IM-500SAA - page 14

    14 5) Remove the front panel and top panel. 6) Move the control switch to the “WASH“ position. 7) Slowly pour the sanitizing solution over the top of the evaporator and into the water tank. Do not splash or spill the solution onto other parts. 8) Replace the front panel and top panel in their correct positions. 9) T urn on the power supply to s ...

  • Hoshizaki IM-500SAA - page 15

    15 21) Replace the front panel. 22) Clean the storage bin liner using a neutral cleaner . Rinse thoroughly after cleaning. 23) T urn on the power supply to start the automatic ice making process. ...

  • Hoshizaki IM-500SAA - page 16

    16 ...

  • Hoshizaki IM-500SAA - page 17

    17 Electrical Specifications: The unit is 115 volt/ 60 hz./1ph. The IM-500SAA should be connected to a separate 20 Amp circuit. ...

  • Hoshizaki IM-500SAA - page 18

    18 ...

  • Hoshizaki IM-500SAA - page 19

    19 ...

  • Hoshizaki IM-500SAA - page 20

    20 ...

  • Hoshizaki IM-500SAA - page 21

    21 ...

  • Hoshizaki IM-500SAA - page 22

    22 ...

  • Hoshizaki IM-500SAA - page 23

    23 IM SERIES REVIEW QUIZ Choose the best answer for each question below. 1. The IM control board is located in the rear or the unit. True False 2. The IM unit uses a thermostatic bin control. True False 3. The bin control switch must OPEN or CLOSE to shut the unit down? 4. The IM series uses R-404A or R-134A refrigerant. 5. The IM-500SAA only uses ...

  • Hoshizaki IM-500SAA - page 24

    24 NOTES: Quiz answers: 1.False, 2. False 3. Op en, 4. R-404A, 5 . True , 6. True, 7. False, 8. False., 9. True ...

Manufacturer Hoshizaki Category Ice Maker

Documents that we receive from a manufacturer of a Hoshizaki IM-500SAA can be divided into several groups. They are, among others:
- Hoshizaki technical drawings
- IM-500SAA manuals
- Hoshizaki product data sheets
- information booklets
- or energy labels Hoshizaki IM-500SAA
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hoshizaki IM-500SAA.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hoshizaki IM-500SAA, service manual, brief instructions and user manuals Hoshizaki IM-500SAA. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hoshizaki IM-500SAA.

Similar manuals

A complete manual for the device Hoshizaki IM-500SAA, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hoshizaki IM-500SAA by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hoshizaki IM-500SAA.

A complete Hoshizaki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hoshizaki IM-500SAA - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hoshizaki IM-500SAA, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hoshizaki IM-500SAA, that we can find in the current document
3. Tips how to use the basic functions of the device Hoshizaki IM-500SAA - which should help us in our first steps of using Hoshizaki IM-500SAA
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hoshizaki IM-500SAA
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hoshizaki IM-500SAA in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hoshizaki IM-500SAA?

Use the form below

If you did not solve your problem by using a manual Hoshizaki IM-500SAA, ask a question using the form below. If a user had a similar problem with Hoshizaki IM-500SAA it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)