English dropdown-ico

Manual Bostitch N400C

16 pages 0.59 mb
Download

Go to site of 16

Summary
  • Bostitch N400C - page 1

    OPERA TION and MAINTENANCE MANUAL MANUAL DE OPERACIÓN Y DE MANTENIMIENT O MANUEL D’INSTRUCTIONS ET D’ENTRETIEN N400C / N401C / N512C COIL-FED PNEUMA TIC NAILER CLA V ADORA NEUMÁTICA ALIMENT ADA POR ROLLO CLOUEUR PNEUMA TIQUE À ENROULEMENT 171 1 19REVB 8/05 BEFORE OPERA TING THIS T OOL, ALL OPERA TORS SHOULD STUDY THIS MANUAL TO UNDERST AND A ...

  • Bostitch N400C - page 2

    SAFETY INSTRUCTIONS EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL WA YS be worn by the operator and others in the work area when connecting to air supply , loading, operating or servicing this tool. Eye protection is required to guard against flying faste ...

  • Bostitch N400C - page 3

    AIR SUPPL Y AND CONNECTIONS Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury . FITTINGS: Install a male plug on the tool which is free flowing and which will release air pressure from the tool when disconnected from the supply source. HOSES: Air hoses should have a m ...

  • Bostitch N400C - page 4

    -7- TOOL OPERA TION EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should AL WA YS be worn by the operator and others in the work area when connecting to air supply , loading, operating or servicing this tool. Eye protection is required to guard against flying faste ...

  • Bostitch N400C - page 5

    IN ADDITION TO THE OTHER W ARNINGS CONT AINED IN THIS MANUAL OBSERVE THE FOLLOWING FOR SAFE OPERA TION • Use the BOSTITCH pneumatic tool only for the purpose for which it was designed. • Never use this tool in a manner that could cause a fastener to be directed toward the user or others in the work area. • Do not use the tool as a hammer . ? ...

  • Bostitch N400C - page 6

    -10- TROUBLESHOOTING PROBLEM CAUSE CORRECTION T rigger valve housing leaks air O-ring cut or cracked . . . . . . . . . . . . . . . . . . . .Replace O-ring T rigger valve stem leaks air O-ring/seals cut or cracked . . . . . . . . . . . . . . . .Replace trigger valve assembly Frame/nose leaks air Loose nose screws . . . . . . . . . . . . . . . . . . ...

  • Bostitch N400C - page 7

    INSTRUCCIONES DE SEGURIDAD Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LA TERALES. Dicha protección ocu ...

  • Bostitch N400C - page 8

    ESPECIFICACIONES LA HERRAMIENT A N64084/N64099 T odos las medidas de tornillos y tuercas son métricas. ESPECIFICACIONES DE LOS CLA VOS: La herramienta N400C, N401C utiliza clavos en rollo secuencial de alambre en largos de 55 - 100 mm (2-1/4 a 4 pulgadas) con diámetros de espiga de 2.5 - 3.8 mm (0.099 –0.148 pulgadas). La herramienta N512C util ...

  • Bostitch N400C - page 9

    OPERACIÓN DE LA HERRAMIENT A Cuando el equipo está conectado al suministro de aire, tanto el operador como todas las personas que se encuentren en el área de trabajo, SIEMPRE deben usar PROTECCIÓN OCULAR que cumpla las especificaciones ANSI para resguardo contra partículas volantes arrojadas desde el FRENTE o los LA TERALES. Dicha protección ...

  • Bostitch N400C - page 10

    -19- ADEMÁS DE LAS OTRAS ADVERTENCIAS CONTENIDAS EN ESTE MANUAL OBSERVE LO SIGUIENTE P ARA LA OPERACIÓN SEGURA • Use la herramienta neumática BOSTITCH solamente para el fin que fue diseñada. • Nunca use esta herramienta en forma que pueda causar la salida de un clavo o grapa hacia el usuario u otros presentes en el área de trabajo. • No ...

  • Bostitch N400C - page 11

    -20- DIAGNÓSTICO DE F ALLA PROBLEMA CAUSA CORRECCIÓN Fuga de aire en la envoltura de la válvula disparadora. Anillo en O cortado o rajado . . . . . . . . . . . . . . .Reemplazar el anillo en O. Vástago de la válvula disparadora tiene fuga de aire . Anillos en O/sellos cortados o rajados. . . . . . . .Reemplazar anillo en O/sellos. Fuga de aire ...

  • Bostitch N400C - page 12

    CONSIGNES DE SÉCURITÉ UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’A V ANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air , du chargement, du fonctionnement et ...

  • Bostitch N400C - page 13

    CARACTÉRISTIQUES DU N400C, N401C, N512C T outes les mesures des vis et des boulons sont dans le système métrique. SPÉCIFICA TIONS DES DISPOSITIFS DE FIXA TION : Les outils N400C et N401C utilisent des clous en cartouche métallique d’une longueur de 55 mm à 100 mm (2 1/2 po à 4 po) et d’un diamètre de tige de 2,5 mm à 3,8 mm (0,099 po ? ...

  • Bostitch N400C - page 14

    -27- FONCTIONNEMENT DE L ’APP AREIL UNE PROTECTION DES YEUX, conforme aux normes ANSI et fournissant une protection contre les projectiles en provenance de l’A V ANT et des CÔTÉS, doit toujours être portée par l’opérateur et les personnes présentes dans la zone de travail, lors du raccordement au réseau d’air , du chargement, du fonc ...

  • Bostitch N400C - page 15

    -29- EN PLUS DES AUTRES A VERTISSEMENTS CONTENUS DANS CE MANUEL, VEILLEZ À OBSERVER LES PRÉCAUTIONS SUIV ANTES : •N ’utilisez jamais l’outil pneumatique BOSTITCH dans un autre but que celui pour lequel il a été conçu. •N ’orientez jamais l’outil de façon à ce qu’il puisse éjecter une attache en direction de l’utilisateur ou ...

  • Bostitch N400C - page 16

    PROBLÈMES DE FONCTIONNEMENT PROBLÈME CAUSE CORRECTION Fuite d’air au corps de valve de détente . . . . . . . Joints toriques coupés ou usés. . . . . . . . . . . . . . . Remplacer les joints toriques . Fuite d’air à la tige de valve de détente. . . . . . . Joints toriques ou garnitures coupés ou usés. . . . . Remplacer joints toriques / ...

Manufacturer Bostitch Category Nail Gun

Documents that we receive from a manufacturer of a Bostitch N400C can be divided into several groups. They are, among others:
- Bostitch technical drawings
- N400C manuals
- Bostitch product data sheets
- information booklets
- or energy labels Bostitch N400C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Bostitch N400C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Bostitch N400C, service manual, brief instructions and user manuals Bostitch N400C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Bostitch N400C.

Similar manuals

A complete manual for the device Bostitch N400C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Bostitch N400C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Bostitch N400C.

A complete Bostitch manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Bostitch N400C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Bostitch N400C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Bostitch N400C, that we can find in the current document
3. Tips how to use the basic functions of the device Bostitch N400C - which should help us in our first steps of using Bostitch N400C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Bostitch N400C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Bostitch N400C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Bostitch N400C?

Use the form below

If you did not solve your problem by using a manual Bostitch N400C, ask a question using the form below. If a user had a similar problem with Bostitch N400C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)