English dropdown-ico

Manual Pelco C1306M-D (7/09)

24 pages 1.26 mb
Download

Go to site of 24

Summary
  • Pelco C1306M-D (7/09) - page 1

    INSTALLATION C1306M-D (7/09) ExSite ® EHXM Series Explosionproof Fixed Sy stem ...

  • Pelco C1306M-D (7/09) - page 2

    2 C1306M-D (7/09) Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco C1306M-D (7/09) - page 3

    C1306M-D (7/09) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed al l warnings. 4. Follow all instructions. 5. Do not bl ock any ven tilation openings. Ins tall in accordance with the manu facturer’ s instructions. 6. T o reduce the risk of ignition of hazar dous atmospheres, di sconnect the equip me ...

  • Pelco C1306M-D (7/09) - page 4

    4 C1306M-D (7/09) Getting Started Thank you for pu rchasing Pe lco’ s ExSite ® EHXM Series explosionproof system. This manu al in cludes in structio ns for i n stalling all th e components of the system. Once the s ystem installati on is comple te, refer to the operat ion/programmi ng manual fo r instructio ns on how to o perate an d program you ...

  • Pelco C1306M-D (7/09) - page 5

    C1306M-D (7/09) 5 Install the Power Module Attach the power module to the mo unting surface. Use only insta llation methods and materials capa ble of supporting fou r times t he maximum specified load o f the system (140 lb /63.5 kg). NOTE: If required, install the option al TXB translator , fiber module , or UTP bo ard before installin g the power ...

  • Pelco C1306M-D (7/09) - page 6

    6 C1306M-D (7/09) CONNECT WIRING Refer to the following informa tion to connect the wires an d cables as required. NOTES: • Relay 3 is a llocated spe cif ically for an external wash er (n ot supplied by Pelco). • All relays are specifie d for 32 VDC, 0.5 A. • Wiring/cable for UTP and fibe r optic are not provided on the wi re harness. T he in ...

  • Pelco C1306M-D (7/09) - page 7

    C1306M-D (7/09) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud se tting for the system. The DIP switches to configure th ese settings are located on the to p of the power module. NOTE: No DIP switch settings are re quired for Coaxitron contr ol. Figure 3 shows the default set tings for the DIP switch es. Refer to the fo ...

  • Pelco C1306M-D (7/09) - page 8

    8 C1306M-D (7/09) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF O FF OFF OFF 2 ON OFF OFF OFF OFF OFF OF F OFF 3 OFF ON OFF OFF OFF OFF OF F OFF 4 ON ON OFF OFF OFF OFF OFF OF F 5 OFF OFF ON OFF OFF OFF OFF OFF 6 ON OFF ON OFF OFF OFF OFF OFF 7 OFF ON ON OFF OFF OFF OFF OF F 8 ON ON ON OFF OFF OFF OFF ...

  • Pelco C1306M-D (7/09) - page 9

    C1306M-D (7/09) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OF F OFF ON ON OFF OF F 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF ON ON OFF OFF 53 ON OFF ON OFF ON ON OFF OFF 54 OFF ON ON OFF ON ON OFF OFF 55 ON ON ON OFF ON ON OFF OFF 56 OFF OFF OFF ON ON ON OFF OFF 57 ON OF ...

  • Pelco C1306M-D (7/09) - page 10

    10 C1306M-D (7/09) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OF F OFF ON 144 OFF OFF OFF OFF ON OFF OFF ON 145 ON OFF OFF OFF ON OFF OFF ON 146 OFF ON OFF OFF ON OF F OFF ON 1 4 7 O N O NO F F O F FO NO F F O F FO N 148 OFF OFF ON OFF ON OFF OFF ON 14 ...

  • Pelco C1306M-D (7/09) - page 11

    C1306M-D (7/09) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 2 3 9 O NO NO NO N O F F O NO NO N 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF ON ON ON ON 2 4 3 O NO N O F F O F F O NO NO NO N 244 OFF OFF ON OFF ON ON ON ON 2 4 5 O N O F F O N O F F O NO NO NO N 246 OFF ON ON OFF ON ON ...

  • Pelco C1306M-D (7/09) - page 12

    12 C1306M-D (7/09) Install the Camera Module T o install the camera mo dule, do th e follo wing: 1. Refer to Figure 4. Loose n the set sc rew at the b ack of the c amera enclosu re with the pr ovided 1.5 mm A llen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanne r wrench to loosen the ba ck of the camera enclosur e (refer to Figure 5). ...

  • Pelco C1306M-D (7/09) - page 13

    C1306M-D (7/09) 13 3. Slide th e camera modul e into the camera enclos ure. Refer t o Figure 6 to position th e camera modul e properly in the came ra encl osur e. Carefully mate the camer a’ s power connector to the mating con nector located inside the camera enclos ure. Models with a wiper: The tab located in side the camera enclosu re must be ...

  • Pelco C1306M-D (7/09) - page 14

    14 C1306M-D (7/09) 4. Models with a wiper: Refer to Figure 8 and do the fo llowing to in stall the ar m of the wipe r: a. Place the su pplied gree n bushing on the stud l ocated be hind the ha ndle of the camera module . The bushin g should be in the sam e orientatio n as shown in Figure 8. b. Install the wiper arm. Pla ce the rid ge of the arm in ...

  • Pelco C1306M-D (7/09) - page 15

    C1306M-D (7/09) 15 Install the Enclosure and Set Pan Position 1. Check fo r proper se ating of t he power modu le seal. Make sure the se al is fully seated in t he groove o n the top of the powe r m odule. Figure 9. Factory-Installed Power Module Seal 2. Refer to Figure 10 and attach the enclosure un it to the power module . Align the pin s of the ...

  • Pelco C1306M-D (7/09) - page 16

    16 C1306M-D (7/09) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nu t and a 21 mm open end wre nch on the tilt shaft (refer to Fig ure 11). Figure 11. Set the T ilt Position 2. Hold the til t shaft in position with the 21 mm wrench, and then turn the 41 mm wrench to loosen the tilt locking ...

  • Pelco C1306M-D (7/09) - page 17

    C1306M-D (7/09) 17 Install the Sun Shroud 1. Place the supplied nylon washer s on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the moun ting holes of the sun shroud with the holes on top of th e camera enclosure. 3. Use the supplied nylo n washers and screws t o secure the sun shroud to th e camera enclosure. Figure 12. Install t ...

  • Pelco C1306M-D (7/09) - page 18

    18 C1306M-D (7/09) Maintenance CAMERA MODULE REPLACEMENT T o replace t he camera mod ule, do the f ollowing: 1. Remove the back cap of the came ra enclosure. Refer to Figur e 13 and do the following: a. Loosen the set screw with a 1 .5 mm Allen wren ch. b. Use the sup plied spanner wren ch to loosen the ba ck cap of the ca mera enclosure. O nce the ...

  • Pelco C1306M-D (7/09) - page 19

    C1306M-D (7/09) 19 3. Models with a wiper: Remove the wiper arm an d the green bushing from the unit (r efer to Figure 14 ). 4. Slide the camera modu le out of the enclosure. 5. Install th e new camera mo dule by doin g the follo wing: Slide the came ra module int o the camera enclosure. Refer to Figur e 15 to posi tion the ca mera module pro perly ...

  • Pelco C1306M-D (7/09) - page 20

    20 C1306M-D (7/09) 6. Models with a wiper: Refer to Figure 14 and do the following to re install the arm of the wipe r: a. Reinstall the gree n bushing on the stud locate d behind the handle of the camera module. b. Reinstall the wip er arm. Place the ridge of the arm in th e notc h of the camera enclosure tab an d the slot of the arm over the gree ...

  • Pelco C1306M-D (7/09) - page 21

    C1306M-D (7/09) 21 Specifications ELECTRICAL Input Voltage 24 VAC or 100-240 V AC, 50/60 Hz Input V olt age Range ±10% Power Consumptio n Maximum 60 W (120 VA) per system Heater and Defroster Microprocessor controlled Electrical Connections 6-foot wire harness with c onnections for power , video, da ta control, alarm i nputs , and auxiliary output ...

  • Pelco C1306M-D (7/09) - page 22

    22 C1306M-D (7/09) *Manual control of camera setup functio ns can be done with CM6700, CM 6800, CM8500, CM 9500, CM9740 , CM9760, CM9770, CM9780, KBD200A , KBD300A, and MPT 9500 control lers, but not with CM75 00, MPT9000, o r KBD9000 contr ollers. CAMERA/OPTICS Camera Day/Night (23X) Color LowLight ™ (22X) Color Signal Format NTSC, P AL NTSC, P ...

  • Pelco C1306M-D (7/09) - page 23

    The materials used in the manufacture of this documen t and it s components are compliant to the requirements of Directive 2002/9 5/EC. This equipment contains elec trical or electronic components that must be recy cled properly to comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrica l and electronic equi ...

  • Pelco C1306M-D (7/09) - page 24

    Pelco, Inc. Worldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .pelco.com ...

Manufacturer Pelco Category Home Security System

Documents that we receive from a manufacturer of a Pelco C1306M-D (7/09) can be divided into several groups. They are, among others:
- Pelco technical drawings
- C1306M-D (7/09) manuals
- Pelco product data sheets
- information booklets
- or energy labels Pelco C1306M-D (7/09)
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pelco C1306M-D (7/09).

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pelco C1306M-D (7/09), service manual, brief instructions and user manuals Pelco C1306M-D (7/09). Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pelco C1306M-D (7/09).

Similar manuals

A complete manual for the device Pelco C1306M-D (7/09), how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pelco C1306M-D (7/09) by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pelco C1306M-D (7/09).

A complete Pelco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pelco C1306M-D (7/09) - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pelco C1306M-D (7/09), FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pelco C1306M-D (7/09), that we can find in the current document
3. Tips how to use the basic functions of the device Pelco C1306M-D (7/09) - which should help us in our first steps of using Pelco C1306M-D (7/09)
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pelco C1306M-D (7/09)
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pelco C1306M-D (7/09) in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pelco C1306M-D (7/09)?

Use the form below

If you did not solve your problem by using a manual Pelco C1306M-D (7/09), ask a question using the form below. If a user had a similar problem with Pelco C1306M-D (7/09) it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)