English dropdown-ico

Manual Tiger Products Co., Ltd 6020009

150 pages 3.59 mb
Download

Go to site of 150

Summary
  • Tiger Products Co., Ltd 6020009 - page 1

    P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS TWIN ROT AR Y ASSEMBLIES Ford TS 100-1 10A CAB, WOC 06020009 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 02/23/2010 ...

  • Tiger Products Co., Ltd 6020009 - page 2

    T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize ...

  • Tiger Products Co., Ltd 6020009 - page 3

    FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . We recommend that yo ...

  • Tiger Products Co., Ltd 6020009 - page 4

    ...

  • Tiger Products Co., Ltd 6020009 - page 5

    T ABLE OF CONTENTS SAFETY _____________________________________________ 1-1 Safety Information__________________________________ 1-2 ASSEMBL Y / MOUNTING SECTION _______________________ 2-1 OPERA TION SECTION _________________________________ 3-1 MAINTENANCE SECTION ______________________________ 4-1 P ARTS SECTION _________________________________ ...

  • Tiger Products Co., Ltd 6020009 - page 6

    ...

  • Tiger Products Co., Ltd 6020009 - page 7

    Twin Rtry Safety Section 1-1 SAFETY SAFETY SECTION ...

  • Tiger Products Co., Ltd 6020009 - page 8

    Twin rtry Safety Section 1-2 SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VERY SERIOUS INJURY . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in MINOR INJU ...

  • Tiger Products Co., Ltd 6020009 - page 9

    Twin Rtry Safety Section 1-3 SAFETY DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency . Never allow inexperienced ...

  • Tiger Products Co., Ltd 6020009 - page 10

    Twin rtry Safety Section 1-4 SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the tractor while the tractor is moving. Mount the tractor only w ...

  • Tiger Products Co., Ltd 6020009 - page 11

    Twin Rtry Safety Section 1-5 SAFETY WARNING! T ransport only at safe speeds. Serious accidents and injuries can result from operating this equipment at unsafe speeds. Understand the T ractor and Implement and how it handles before transporting on streets and highways. Make sure the T ractor steering and brakes are in good condition and operate prop ...

  • Tiger Products Co., Ltd 6020009 - page 12

    Twin rtry Safety Section 1-6 SAFETY WARNING! Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. Make sure the tractor engine is OFF before working on the Implement. (SG-20) WARNING! Periodically inspect all moving parts for wear and replace when necessary with authoriz ...

  • Tiger Products Co., Ltd 6020009 - page 13

    Twin Rtry Safety Section 1-7 SAFETY DANGER! NEVER use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability t o operate the equipment safely. Before operating the Tractor or Imple- ment, an operator on p ...

  • Tiger Products Co., Ltd 6020009 - page 14

    Twin rtry Safety Section 1-8 SAFETY WARNING! Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must be clearly ma ...

  • Tiger Products Co., Ltd 6020009 - page 15

    Twin Rtry Safety Section 1-9 SAFETY DANGER! Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working condit ...

  • Tiger Products Co., Ltd 6020009 - page 16

    Twin rtry Safety Section 1-10 SAFETY WARNING! The rotating parts of this machine continue to rotate even after the Tractor has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased. (SBM-5) “Wait a minute...Save a lif ...

  • Tiger Products Co., Ltd 6020009 - page 17

    Twin Rtry Safety Section 1-11 SAFETY WARNING! In addition to the design and configuration of this Implement, including Safety Signs and Safety Equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of personnel involved in the operation, transport, maintenance, and storage of the m ...

  • Tiger Products Co., Ltd 6020009 - page 18

    Twin rtry Safety Section 1-12 SAFETY 22840 INSIDE OF CAB 22839 MOWER DECK 24028 MOWER DECK 10” x 5.5” 31522 MOWER DECK 18.25” x10” 31523 HYDRAULIC T ANK P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 19

    Twin Rtry Safety Section 1-13 SAFETY 33743 INSIDE OF CAB 42350 MOWER DECK 42399 MOWER DECK 42400 MOWER DECK P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 20

    Twin rtry Safety Section 1-14 SAFETY 6T3219 INSIDE OF CAB 6T3217 MOWER DECK 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 21

    Twin Rtry Safety Section 1-15 SAFETY INSIDE OF CAB 6T3222 INSIDE OF CAB 6T3224 MOWER DECK 6T3230 INSIDE OF CAB P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 22

    Twin rtry Safety Section 1-16 SAFETY 6T3234 INSIDE OF CAB 6T3233 HYDRAULIC T ANK 6T3236 MOWER DECK HYDRAULIC T ANK 6T3243 INSIDE OF CAB P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 23

    Twin Rtry Safety Section 1-17 SAFETY 6T3261 MOWER DECK 6T3249A MOWER DECK TB101 1 MOWER DECK P AR T NO. LOCA TION ...

  • Tiger Products Co., Ltd 6020009 - page 24

    Twin rtry Safety Section 1-18 SAFETY 34852 HYDRAULIC T ANK ...

  • Tiger Products Co., Ltd 6020009 - page 25

    Twin Rtry Safety Section 1-19 SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 ROUND MANUAL CANISTER 33997 1 DECAL, SHEET, MANUAL CANISTER 2 * DECAL 3 * DECAL 4 * DECAL 5 * AVAIL SPECIFIC PRODUCT MANUAL 6 33753 1 E M I SAFETY MANUAL 7 34296 1 FRONT ADHESIVE PAD 8 34297 1 REAR ADHESIVE PAD 9 6T1823 4 ZIP TIE 14 ...

  • Tiger Products Co., Ltd 6020009 - page 26

    Twin rtry Safety Section 1-20 SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such . Employer-Employee Operator Regulations U.S. Publ ...

  • Tiger Products Co., Ltd 6020009 - page 27

    ASSEMBL Y SECTION Assembly Section 2-1 ...

  • Tiger Products Co., Ltd 6020009 - page 28

    Assembly Section 2-2 ASSEMBL Y Before attempting to mount or service your Tiger mower , it is import ant to read and understand all of the information in the Safety section of this manual. Check complete shipment list against the packing list to make sure there are no shortages. Make certain the tractor model is the appropriate one for the mower re ...

  • Tiger Products Co., Ltd 6020009 - page 29

    Assembly Section 2-3 ASSEMBL Y ADJUSTING REAR WHEELS Raise rear of tractor onto jack-stands. Follow the instructions in the tractor owners manual for adjusting tires and rims to 72” center for side mounted mowers and 79.8” for boom mowers. NOTE: This may require switching the wheels to opposite sides of tractor . CRANKSHAFT ADAPTER If necessary ...

  • Tiger Products Co., Ltd 6020009 - page 30

    Assembly Section 2-4 ASSEMBL Y LIFT V A L VE MOUNT Install the valve mounting bracket to the inside of the right and left rear fender frame tube as shown below . Align the valve mounting plate with the drilled holes. Mark the center of one of the holes above and in line with the slotted holes in the valve plate. Do not use any holes that will be us ...

  • Tiger Products Co., Ltd 6020009 - page 31

    Assembly Section 2-5 ASSEMBL Y WEA THER-P ACK/METRI-P ACK ASSEMBL Y These instructions apply to both Weather-Pack and Metri-pack connectors. NOTE: Use the specific tool for the type of connector you are assembling. 1. Apply seal to cable, before stripping insulation. 2. Align seal with cable insulation. 3. Put terminal in crimping tool, then positi ...

  • Tiger Products Co., Ltd 6020009 - page 32

    Assembly Section 2-6 ASSEMBL Y POL Y -CARBONA TE SAFETY WINDOW NOTE: This should be done before mounting the main frame. 1. Disconnect gas shock at door . Remove the right side cab door from tractor cab by removing hinge pins. 2. Remove the existing hardware and discard factory glass door . 3. Place small beed of adhesive seal in the botom of the t ...

  • Tiger Products Co., Ltd 6020009 - page 33

    Assembly Section 2-7 ASSEMBL Y FRONT WORKLAMP RELOCA TION 1. Cut the right side front hand rail from the bottom of worklamp to the bottom of the hand rail. 2 Bend the hand rail inside to avoid the boom collision with the worklamp. INST ALLING MIRROR BRACKET Install the mirror mounting bracket to the tractor cab using supplied hardware. Cut the muff ...

  • Tiger Products Co., Ltd 6020009 - page 34

    Assembly Section 2-8 ASSEMBL Y EXHAUST MOUNT NOTE: This should be done after mounting the main frame. 1. Cut the tractor hood as shown in pic. # 1 to accomodate modified exhaust turbo tube. 2 Remove the muffler from existing turbo tube. 3. Remove existing turbo tube from tractor turbo. 4. Install the exhaust mounting bracket and supporting brace. 5 ...

  • Tiger Products Co., Ltd 6020009 - page 35

    Assembly Section 2-9 ASSEMBL Y Picture # 4 Picture # 5 ...

  • Tiger Products Co., Ltd 6020009 - page 36

    Assembly Section 2-10 ASSEMBL Y SWITCH MOUNTING Refer to the parts section for wiring diagrams. Remove top instrument panel (tach, and hour meter) for access to the wires. Route the red and green wire from the switch box wires from the switch box to the bottom right corner of the instrumentm panel near window . Connect the red wire to the white wir ...

  • Tiger Products Co., Ltd 6020009 - page 37

    Assembly Section 2-11 ASSEMBL Y ...

  • Tiger Products Co., Ltd 6020009 - page 38

    Assembly Section 2-12 ASSEMBL Y FRONT PUMP MOUNTING Install the pump mounting bracket on the front of the tractor with cap-screws and lock-washers as shown in the parts section illustration. DO NOT tighten fasteners at this time. Slide the pump drive shaft into the crankshaft adapter . The end with the shorter splines should be inserted into the ad ...

  • Tiger Products Co., Ltd 6020009 - page 39

    Assembly Section 2-13 ASSEMBL Y INST ALLING O-RING FITTINGS Installing straight, 45 degree and 90 degree O-ring fittings requires that the O- ring, washer and nut (A) be up against the swivel body (B). Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set direction with a ...

  • Tiger Products Co., Ltd 6020009 - page 40

    Assembly Section 2-14 ASSEMBL Y CABLE LIFT DRAFT BEAM INST ALLA TION Install ½” O-ring breather into butt port of inboard cylinder . In all fittings in the rod end of the cylinder according to diagrams in parts section. These fittings should be positioned to face the butt end of the cylinder . Next turn the clevis onto the rod of the cylinder un ...

  • Tiger Products Co., Ltd 6020009 - page 41

    Assembly Section 2-15 ASSEMBL Y DRAFT BEAM MOUNTING Pull the inboard cylinder piston rod down to the extreme extended position. Slide the draft beam under the cylinder , and align clevis hole with draft beam hole nearest to the tractor . Install pin and secure with R-clips. Using inboard cylinder as a pivot point, slide draft beam under tractor and ...

  • Tiger Products Co., Ltd 6020009 - page 42

    Assembly Section 2-16 ASSEMBL Y Check for oil leaks at all fittings and connections using a piece of paper or cardboard. DO NOT USE HANDS TO CHECK FOR FLUID LEAKS! Raise the tree point hitch and check the tractor internal hydraulics, fill to proper level if needed. DECK MOUNTING AND LIFT ASSEMBL Y Install the upper sheave bracket on the outboard cy ...

  • Tiger Products Co., Ltd 6020009 - page 43

    Assembly Section 2-17 ASSEMBL Y TURNBUCKLE ADJUSTMENT Extend the outboard cylinder until the deck touches the stop on the draft beam. Hold the deck in this position to adjust the lift cable tension. Adjust turn buckle until cable is tight. Lower and raise the deck to check adjustment. The mower deck should reach it’s stop on the draft beam at the ...

  • Tiger Products Co., Ltd 6020009 - page 44

    Assembly Section 2-18 ASSEMBL Y DRAFT BEAM MOUNTING Pull the inboard cylinder piston rod down to the extreme extended position. Slide the draft beam under the cylinder , and align clevis hole with draft beam hole nearest to the tractor . Inst all pin and secure with R-clips. Using inboard cylinder as a pivot point, slide draft beam under tractor an ...

  • Tiger Products Co., Ltd 6020009 - page 45

    Assembly Section 2-19 ASSEMBL Y DECK / MOTOR FEEDLINE Install the 1” hose with the 180 degree flange on the front side of the motor to the top of the solenoid valve. Secure to motor with flange kit, and install swivel fittings on the other end. Install the other 1” hose with the 60 degree flange on the back side of the motor to the bottom of th ...

  • Tiger Products Co., Ltd 6020009 - page 46

    Assembly Section 2-20 ASSEMBL Y DECK / MOTOR FEEDLINE MOUNTING (cont.) Be sure that all grease zerks are installed in the draft beam pin bosses. Grease all areas of the draft beam according to the instructions in the maintenance section. Re-check all fittings for tightness and be sure teflon tape has been used at all connections. Fill hydraulic tan ...

  • Tiger Products Co., Ltd 6020009 - page 47

    Assembly Section 2-21 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book. The decals are to ...

  • Tiger Products Co., Ltd 6020009 - page 48

    Assembly Section 2-22 ASSEMBL Y ...

  • Tiger Products Co., Ltd 6020009 - page 49

    Twin rtry Operation Section 3-1 OPERA TION OPERA TION SECTION ...

  • Tiger Products Co., Ltd 6020009 - page 50

    Twion Rtry Operation Section 3-2 OPERA TION Safety is of primary importance to the owner / operator and to the manufacturer . The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the messages will be repeated throughout the manual. The own ...

  • Tiger Products Co., Ltd 6020009 - page 51

    Twin rtry Operation Section 3-3 OPERA TION ST ARTING TRACT OR AND MOWER Check the operators manual received from the tractor manufacturer , for their recommendation and procedures pertaining to your particular make and model. When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow ...

  • Tiger Products Co., Ltd 6020009 - page 52

    Twion Rtry Operation Section 3-4 OPERA TION CONTROL LOCA TION AND FUNCTIONS The side mower height is controlled with a two or three spool valve and is coordinated as shown below . The optional three spool valve allows for the operation of a rear rotary mower or side ditcher . If the unit is equipped with a three spool valve, do not operate the thir ...

  • Tiger Products Co., Ltd 6020009 - page 53

    Twin rtry Operation Section 3-5 OPERA TION Once on location, lower the mower deck slightly above the material to be cut, so the mower does not have to start under a load. Bring the R.P .M. of the tractor up to 1200 and engage the side mower . If a rear mower is being used, allow the R.P .M. to return to 1200 before engaging the rear mower . The rot ...

  • Tiger Products Co., Ltd 6020009 - page 54

    Twion Rtry Operation Section 3-6 OPERA TION When encountering a very severe condition which causes the tractor to stall, disengage mower , start tractor , raise the mower from the cut. Shut tractor off and inspect the mower , blades and disk for damage before engaging mower again. If the blades jam or stop, disengage the clutch and raise the head s ...

  • Tiger Products Co., Ltd 6020009 - page 55

    Twin rtry Operation Section 3-7 OPERA TION TRANSPORTING MOWER T ransporting under the units own power: When transporting between job sites or between cutting passes, the following procedure should be followed: Shut off the power to the cutting head(s) and allow all motion to come to a complete stop. Raise the draft beam to it’s highest position. ...

  • Tiger Products Co., Ltd 6020009 - page 56

    Twion Rtry Operation Section 3-8 OPERA TION Next, switch the hose ends and reconnect to form two separate closed loops, see diagram below . Disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. Remove the keeper bolt and draft beam outer pivot pin. Separate the mower head from the tractor . Now ...

  • Tiger Products Co., Ltd 6020009 - page 57

    Twin rtry Operation Section 3-9 OPERA TION INSPECTION SHEETS ...

  • Tiger Products Co., Ltd 6020009 - page 58

    Twion Rtry Operation Section 3-10 OPERA TION Rotary Mower PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all r otation has stop and the tractor is in the Park with the parking brake engaged. The ...

  • Tiger Products Co., Ltd 6020009 - page 59

    Twin rtry Operation Section 3-11 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is of f, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mower ...

  • Tiger Products Co., Ltd 6020009 - page 60

    Twion Rtry Operation Section 3-12 OPERA TION FRONT END LOADER PRE-OPERA TION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loa ...

  • Tiger Products Co., Ltd 6020009 - page 61

    Twin rtry Operation Section 3-13 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loader ...

  • Tiger Products Co., Ltd 6020009 - page 62

    Twion Rtry Operation Section 3-14 OPERA TION ...

  • Tiger Products Co., Ltd 6020009 - page 63

    Twin Rtry Maintenance Section 4-1 MAINTENANCE MAINTENANCE SECTION ...

  • Tiger Products Co., Ltd 6020009 - page 64

    Twin Rtry Maintenance Section 4-2 MAINTENANCE T iger Mowers are designed for high performance and rugged durability , yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower . Regular maintenance at the intervals mentioned will result in the maximum efficiency and long ...

  • Tiger Products Co., Ltd 6020009 - page 65

    Twin Rtry Maintenance Section 4-3 MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. This symbol indicates a point that needs to be greased at an interval noted in the section below . Refer to the Detail ...

  • Tiger Products Co., Ltd 6020009 - page 66

    Twin Rtry Maintenance Section 4-4 MAINTENANCE WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly In-Line High Pressure Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly MONTHL Y OR EVE ...

  • Tiger Products Co., Ltd 6020009 - page 67

    Twin Rtry Maintenance Section 4-5 MAINTENANCE SYMPTOMS CAUSE REMEDY Oil T emperature rises 1 . Low oil level 1. Bring oil to proper level above 200 deg. F 2. Kinked or blocked 2. Inspect, Repair , or Replace hoses 3. Worn pump/motor 3. Disable and repair Mower will not start 1 . Blown fuse 1. Check fuse between mower switch or run and ignition / re ...

  • Tiger Products Co., Ltd 6020009 - page 68

    Twin Rtry Maintenance Section 4-6 MAINTENANCE Motor will not work 1. Excessive wear 1. Disassemble and repair . on internal parts NOTE: If flow meter is available, check pressure and flow volume for all suspected hydraulic problems. If the solution to your problem cannot be found in this section, call the T echnical Service representative at the nu ...

  • Tiger Products Co., Ltd 6020009 - page 69

    Twin Rtry Maintenance Section 4-7 MAINTENANCE T ORQUE SPECIFICA TIONS * These are intended to be general specifications. See tractor operators or service manual for exact specifications for your unit. ...

  • Tiger Products Co., Ltd 6020009 - page 70

    Twin Rtry Maintenance Section 4-8 MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General Specification Recomended Mobil Lubricant Tractor Hydraulics Reservoir JD-20C Mobilfluid 424 MF M1 135,M1 141 FNHM2C134D (FNH201) Mower Hydraulics Reservoir Cold T emperatures 0 F S t art-Up ISO 46 Anti-Wear - Low T emp Mobil DTE 15M Normal T ...

  • Tiger Products Co., Ltd 6020009 - page 71

    Twin Rtry Maintenance Section 4-9 MAINTENANCE POL YCARBONA TE CARE & MAINTENANCE The proprietary UV and Abrasion Resistant surface coating on SHIELDS ® SUPERCOA TED ™ polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life. T iger Corp. polyca ...

  • Tiger Products Co., Ltd 6020009 - page 72

    Twin Rtry Maintenance Section 4-10 MAINTENANCE RECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVIORS When filling or checking the oil level, the unit should be parked on a level surface, shut “ OFF ”, and allowed sufficient time to cool to ambient temperature. Use caution when removing the pressurized breather . Do not place face over openi ...

  • Tiger Products Co., Ltd 6020009 - page 73

    Twin Rtry Maintenance Section 4-11 MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut down and de-pressurized. Locate High Pressure Filter housing. Confirm that the element that is about to be installed matches the element p/n on the filter model tag. Example: V3.0510-06 (world line 10 ...

  • Tiger Products Co., Ltd 6020009 - page 74

    Twin Rtry Maintenance Section 4-12 MAINTENANCE GREASING INNER AND OUTER DRAFT BEAM PIVOT POINTS Locate the grease zerks on the inner and outer draft beam pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into each zerk until grease protrudes from joints. Grease all pivots daily or every 8 hours ...

  • Tiger Products Co., Ltd 6020009 - page 75

    Twin Rtry Maintenance Section 4-13 MAINTENANCE DRIVE SHAFT YOKE, U-JOINT & STUB SHAFT With engine stopped, inject Lithium-Complex extreme pressure grease conforming to NLGI2-ISO 320 specifications into universal joints and slip yoke untill grease appears at the seal. Grease daily or every 10 hours. Do not over grease. GREASING PUMP DRIVE SHAFT ...

  • Tiger Products Co., Ltd 6020009 - page 76

    Twin Rtry Maintenance Section 4-14 MAINTENANCE ADJUSTING THE CABLE LIFT Extend the outboard cylinder until the mower deck touches its stop on the draft beam as shown. NOTE: Make sure the cable turnbuckle is loose enough to allow the cylinder to reach full extension before the head reaches the stop. Now hold the head against the stop and tighten the ...

  • Tiger Products Co., Ltd 6020009 - page 77

    Twin Rtry Maintenance Section 4-15 MAINTENANCE BALL V AL VES The ball valve at the hydraulic reservoir may need to be closed during certain maintenance or repair procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with valve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .T .O. ! Failure to do so may result in component fail ...

  • Tiger Products Co., Ltd 6020009 - page 78

    Twin Rtry Maintenance Section 4-16 MAINTENANCE GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject T iger S pindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal. Lubricate spindle weekly or every 40 hours of use. TIGHTENING SPINDLE BOL TS The spindle ...

  • Tiger Products Co., Ltd 6020009 - page 79

    Twin Rtry Maintenance Section 4-17 MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1 – Be sure you have a complete matching set of new knives for replacement. 2 – Remove knives and inspect holes for damage. Also watch for cracks in the disk around the holes. 3 – Lube threads with anti-seize, motor oil or grease. Install bolt through knife and disk fro ...

  • Tiger Products Co., Ltd 6020009 - page 80

    Twin Rtry Maintenance Section 4-18 MAINTENANCE REPLACEMENT OF ROT AR Y DISK Failure to follow the following warnings and instructions may result in serious injury or damage to the equipment or property! The bolts that attach the knife mounting disk to the spindle must be grade 8. These 5/8 inch bolts are to be torqued to 225 ft. lbs. A thread locki ...

  • Tiger Products Co., Ltd 6020009 - page 81

    Twin Rtry Maintenance Section 4-19 MAINTENANCE HEA VY DUTY SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT W ARNING! A press MUST be used to inst all bearing cups, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged. NOTE: The grease zerk and gussets are located on the top ...

  • Tiger Products Co., Ltd 6020009 - page 82

    Twin Rtry Maintenance Section 4-20 MAINTENANCE BEARING INST ALLA TION 1 – Press upper bearing cup into the spindle housing. 2 – T urn the spindle housing over and press in the lower bearing cup. 3 – Place the lower bearing cone in the bearing cup. Next press the seal into the spindle housing. The inner lip of the seal must be DOWN, towards th ...

  • Tiger Products Co., Ltd 6020009 - page 83

    Twin Rtry Maintenance Section 4-21 MAINTENANCE BEARING ADJUSTMENT 1 – Clamp the bottom end of the spindle securely in a vise so the spindle housing turns freely . 2 – Position a magnetic base dial indicator on the stationary cylinder of the spindle housing. Locate the end of the dial indicator against the flat end of the spindle shaft. The dial ...

  • Tiger Products Co., Ltd 6020009 - page 84

    Twin Rtry Maintenance Section 4-22 MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operators manual. ______ Pump Drive Shaft: If required with drive shaft / coupler check for end play and lubricate at zerks. ______ Crankshaft ...

  • Tiger Products Co., Ltd 6020009 - page 85

    P ARTS SECTION FORD TS 1 15-135A CAB, WOC, TWIN ROT AR Y Parts Section 5-1 ...

  • Tiger Products Co., Ltd 6020009 - page 86

    Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locat ...

  • Tiger Products Co., Ltd 6020009 - page 87

    Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION ASSEMBL Y P AGE TRACTOR SPECIFIC P ARTS: TRACTOR MOUNT KIT – MAIN FRAME 06101031-37 5-4 TRACTOR MOUNT KIT - HYDRAULICS,TRR 06101031-37 5-6 TRACTOR MOUNT KIT - HYDRAULICS,TRAILKA T 06101031-37 5-8 TRAC. MNT . KIT – BRACE / BA TT ., CAB / WOC 06101031-37 5-10 CABLE LIFT V AL VE – 2SP , ...

  • Tiger Products Co., Ltd 6020009 - page 88

    Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME ...

  • Tiger Products Co., Ltd 6020009 - page 89

    Parts Section 5-5 R 7-98 TRACTOR MOUNT KIT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 06300009 1 MAIN FRAME, TSA 1 15 2 06380001 1 REAR RESERVOIR SUPPORT 3 06380002 1 FRONT RESERVOR SUPPORT 4 32667 1 RESERVOIR T ANK FRAME 5 32669 1 RESERVOIR T ANK STRAP 06700006 A V AIL. RESERVOIR T ANK ASSY , TSA. 6 21627 4 NYLOCK NUTS 7 06380000 1 RESER VOIR T ...

  • Tiger Products Co., Ltd 6020009 - page 90

    Parts Section 5-6 TRACTOR MOUNT KIT - HYDRAULICS, TRR ...

  • Tiger Products Co., Ltd 6020009 - page 91

    Parts Section 5-7 4-22-02 TRACTOR MOUNT KIT - HYDRAULICS, TRR ITEM PART NO. QTY. DESCRIPTION 1 32869 1 NIPPLE,MALE LONG ,1MOR X 1MJ 2 06505017 1 CLAMP KIT ,1 HOSE,1" 4 34067 1 ADAPTER,1 1/4MORX1 1/4MJ 5 34069 1 BALL V AL VE,1-1/4FOR 6 24724 1 SWIVEL 7 34183 1 BULKHEAD ADAPTER 9 06500065 1 HOSE,1-1/4x55(1-1/4FJXx20FLG45) 10 TF4852 2 #20 FLANGE ...

  • Tiger Products Co., Ltd 6020009 - page 92

    Parts Section 5-8 TRACT OR MOUNT KIT - HYDRAULICS, TRAILKA T ...

  • Tiger Products Co., Ltd 6020009 - page 93

    Parts Section 5-9 4-22-02 TRACTOR MOUNT KIT - HYDRAULICS, TRAILKA T ITEM PART NO. QTY. DESCRIPTION 1 32869 1 NIPPLE,MALE LONG ,1MOR X 1MJ 2 06505017 1 CLAMP KIT ,1 HOSE,1" 4 34067 1 ADAPTER,1 1/4MORX1 1/4MJ 5 34069 1 BALL V AL VE,1-1/4FOR 6 24724 1 SWIVEL 7 34183 1 BULKHEAD ADAPTER 9 06500105 1 HOSE,1 1/4x55(1 1/4FJXx24FLG45 10 TF4852 2 #20 FL ...

  • Tiger Products Co., Ltd 6020009 - page 94

    Parts Section 5-10 TRACTOR MOUNT KIT - BRACE/BA TT , CAB/WOC ...

  • Tiger Products Co., Ltd 6020009 - page 95

    Parts Section 5-11 R 5-00 TRACTOR MOUNT KIT - BRACE/BA TT , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 0630001 1 1 AXLE BRACE, RH NHTSA 1 15 1A 06300012 1 AXLE BRACE, LH NHTSA 1 15 2 21833 2 CAPSCREW - 3/4" X 2 1/4" 3 21993 8 LOCKWASHER - 3/4" 4 21825 6 HEX NUT - 3/4" 5 0637001 1 1 BATT MN T , TS 100-135A 6 * 2 EXISTING HARDWARE 7 ...

  • Tiger Products Co., Ltd 6020009 - page 96

    Parts Section 5-12 CABLE LIFT V AL VE - 2SP , CAB/WOC ...

  • Tiger Products Co., Ltd 6020009 - page 97

    Parts Section 5-13 R 7-98 CABLE LIFT V AL VE - 2SP , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31320 1 VALVE,2SP,HSC,TM,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 V A L V E M O U N TING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 06510027 1 S WTCHBX ASSY,TWIN/T3F,REV FAN 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL BO ...

  • Tiger Products Co., Ltd 6020009 - page 98

    Parts Section 5-14 COMBO LIFT V AL VE - 2SP , CAB/WOC ...

  • Tiger Products Co., Ltd 6020009 - page 99

    Parts Section 5-15 R 7-98 COMBO LIFT V AL VE - 2SP , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31321 1 VALVE,2SP,HSC,TM,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 V A L V E M O U N TING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 06510027 1 S WTCHBX ASSY,TWIN/T3F,REV FAN 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL BO ...

  • Tiger Products Co., Ltd 6020009 - page 100

    Parts Section 5-16 CABLE LIFT V AL VE - 3SP , CAB/WOC ...

  • Tiger Products Co., Ltd 6020009 - page 101

    Parts Section 5-17 CABLE LIFT V AL VE - 3SP , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31323 1 VALVE,3SP,HSC,TM,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 V A L V E M O U N TING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 06510027 1 S WTCHBX ASSY,TWIN/T3F,REV FAN 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL BOX 8 346 ...

  • Tiger Products Co., Ltd 6020009 - page 102

    Parts Section 5-18 COMBO LIFT V AL VE - 3SP , CAB/WOC ...

  • Tiger Products Co., Ltd 6020009 - page 103

    Parts Section 5-19 COMBO LIFT V AL VE - 3SP , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31324 1 VALVE,3SP,HSC,TRR, COMBO,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 V A L V E M O U N TING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 06510027 1 S WTCHBX ASSY,TWIN/T3F,REV FAN 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL B ...

  • Tiger Products Co., Ltd 6020009 - page 104

    Parts Section 5-20 MIRROR BRACKET ...

  • Tiger Products Co., Ltd 6020009 - page 105

    Parts Section 5-21 MIRROR BRACKET ITEM PART NO. QTY. DESCRIPTION 1 * 1 WORK LIGHT (EXISTING) 2 * 1 MIRROR KNOB (EXISTING) 3 * 1 MIRROR (EXISTING) 4 * 1 EXHAUST MUFFLER (EXISTING) 5 06370008 1 MNT ,MIRROR/LIGHT ,TS1 15A 6 06410141 1 COLLAR,EXHAUST ,TS1 15A 7 06410142 1 COLLAR,CLAMP ,EXHAUST ,TS1 15A 8 21530 2 CAPSCREW ,1/4 X 1 NC 9 21525 4 HEX NUT , ...

  • Tiger Products Co., Ltd 6020009 - page 106

    Parts Section 5-22 HYDRAULIC COOLER ASSEMBL Y , CAB ...

  • Tiger Products Co., Ltd 6020009 - page 107

    Parts Section 5-23 ITEM PART NO. QTY. DESCRIPTION 1 06510026 1 COOLER,SNGL F AN,350BTU 06510029 A V AIL. F AN ASSY ,COOLERS,06510025-26 2 06370012 1 COOLER MNT ,RH,FRNT ,PMP MNT 3 06370013 1 COOLER MNT ,LH,FRNT ,PMP MNT 4 21835 4 CAPSCREW ,3/4 X 2-3/4 NC 5 22021 4 F L A T W ASHER,3/4 6 21993 4 LOCKWASHER,3/4,GR 8 7 21825 4 HEX NUT ,3/4 NC 8 32876 1 ...

  • Tiger Products Co., Ltd 6020009 - page 108

    Parts Section 5-24 BOOM POL YCARBONA TE CAB SAFETY WINDOW KIT R 00-00 ITEM PART NO. QTY. DESCRIPTION 1 06490004 1 P OL YCARBONA TE, NHTSA 1 15, DOOR, RH 2 31965 17 ” TRIM SEAL, 3/8 CLIP X 3/4 OD BULB 3 06530502 2 CAPSCREW 8 MM X 40 MM GR8 4 * 8 EXISTING HARDWARE 5 06530501 1 CAPSCREW 6 MM X 25 MM GR8 6 06537006 1 THREADED INSERT 1/4 X 1/2 NC 7 21 ...

  • Tiger Products Co., Ltd 6020009 - page 109

    Parts Section 5-25 NON-CAB STEEL CANOPY - OPTIONAL ITEM PART NO. QTY. DESCRIPTION 1 6T6902 1 CANOPY 2 32730 2 S P ACER CANOPY BRACKET 3 32727 2 CANOPY BRACKET 4 0642003 4 U-BOL T ,3.25x5.00x.50,20NF ,GR8 5 21700 1 4 HEX NUT - 1/2" NF 6 21990 1 4 LOCKWASHER - 1/2" 7 21730 6 CAPSCREW - 1/2" X 1 1/4" 8 28053 4.8' TRIM-LOCK 9 2 ...

  • Tiger Products Co., Ltd 6020009 - page 110

    ITEM PART NO. QTY. DESCRIPTION 1 064101 13 1 MNT ,EXHAUST ,TSA1 15-135 2 06410121 1 MNT ,EXHAUST ,SUPPORT ,TSA1 15-135 3 06520023 1 TUBE,EXHAUST RELOCA TE,TSA,6CYL 4 32986 2 CLAMP ,EXHAUST ,3 1/2 5 21630 4 CAPSCREW ,3/8x1,NC 6 21988 4 LOCKWASHER,3/8 7 21625 4 HEX NUT ,3/8 NC 8 * 2 EXISTING MAINFRAME HARDWARE EXHAUST MOUNT ...

  • Tiger Products Co., Ltd 6020009 - page 111

    R 7-98 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32876 1 GUARD, TANDUM PUMP UNIVERSAL 2 32737 1 UNIVERSAL GRILL GUARD 3 21637 4 C A PSCREW - 3/4 X 2-3/4 4 22021 4 FLATWASHER - 3/4 5 21993 4 LOCKWASHER - 3/4 6 21825 4 HEX NUT - 3/4 ...

  • Tiger Products Co., Ltd 6020009 - page 112

    Parts Section 5-28 BRAKE V AL VE SOLENOID 12-17-02 ITEM PART NO. QTY. DESCRIPTION * 34115 AVAIL SOLENOID BRAKE VALVE ASSEMBLY - HIGH PRESSURE 1 34092 1 BRAKE VALE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 34093 1 SOLENOID, 2 POSITION, 3 WAY 5 34091 1 RELIEF VALVE, 2600 PSI ** 34096 2 RELIEF SEAL KIT ** 34097 1 SOLENOID SEAL ...

  • Tiger Products Co., Ltd 6020009 - page 113

    Parts Section 5-29 R 7-98 SOLENOID V AL VE SWITCH AND WIRING ITEM P ART NO. QTY . DESCRIPTION 06510027 A V A IL SWTCHBX ASSY ,TWIN/T3F ,REV F AN ASY 1 6T3923 1 INDICA TOR LIGHT 2 35227 1 RELA Y 3 6T3934 O P T . TEMPERA TURE GAUGE 4 6T3931 O P T . TEMPERA TURE SENSOR 5 6T3927 1 CONTINUOUS SOLENOID SWITCH 6 34532 1 TOGGLE SWITCH, MOWER RUN 7 06510028 ...

  • Tiger Products Co., Ltd 6020009 - page 114

    Parts Section 5-30 ...

  • Tiger Products Co., Ltd 6020009 - page 115

    TWIN ROT AR Y COMMON SECTION COMMON P ARTS SECTION ...

  • Tiger Products Co., Ltd 6020009 - page 116

    Twin Rotary Common Section 6-2 SECTION ASSEMBL Y P AGE REAR ROT ARY DECK ASSEMBL Y 6-4 TRAILKA T® REAR ROT AR Y DECK ASSY 6-6 REAR RT R Y CASTER WHEEL & 3PT ASSEMBL Y 6-8 REAR ROT AR Y HYDRAULICS 6-10 ROT ARY M OTORS 6-12 TWIN PUMP 6-14 HUSCO V AL VES 6-16 COOLER ASSEMBL Y 6-24 SAFETY ST AND 6-26 CASTER WHEEL ASSEMBL Y 6-27 BRAKE V AL VE WITH ...

  • Tiger Products Co., Ltd 6020009 - page 117

    Twin Rotary Common Section 6-3 12-12-02 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions a ...

  • Tiger Products Co., Ltd 6020009 - page 118

    Twin Rotary Common Section 6-4 REAR ROT AR Y DECK ASSEMBL Y ...

  • Tiger Products Co., Ltd 6020009 - page 119

    Twin Rotary Common Section 6-5 REAR ROT AR Y DECK ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION ** 23003 R E F . REAR RT RY , 60” W/REAR CHAINS 1 32616 1 RT RY , 60" DECK, TRR 2 6T1024H5 1 SPINDLE ASSY ,CPL T ,HD,5/8 HOLES 3 6T2277 6 CAPSCREW , 3/4" x 2" NF 4 21993 6 LOCKWASHER,3/4",GR 8 5 6T2413 6 HEX NUT ,3/4,NF ,GR 8 6 SEE DIS ...

  • Tiger Products Co., Ltd 6020009 - page 120

    Twin Rotary Common Section 6-6 TRAILKA T® REAR ROT AR Y DECK ASSY NOTE ORIENT A TION OF ITEM 34, LARGE ZERK FORWARD ...

  • Tiger Products Co., Ltd 6020009 - page 121

    Twin Rotary Common Section 6-7 TRAILKA T® REAR ROT AR Y DECK ASSY ITEM P A R T N O . Q TY . DESCRIPTION 1 06320002 1 TRAILKA T®,60,WLDMNT 2 6T01 12 2 SHACKLE,W/PIN,CPL T 3 22051 1 CABLE,LIFT ,TRR,60 4 TB1033 2 PIN,CLEVIS,1 x 4 5 06537021 4 ROLLPIN,5mm x 50mm,SS 6 21474A 1 HITCH,3PT ,TRR 7 2851 1 1 S T AND,SAFETY SUPPORT W/P AD 8 23329 1 CASTER WH ...

  • Tiger Products Co., Ltd 6020009 - page 122

    Twin Rotary Common Section 6-8 REAR ROT AR Y CASTER WHEEL & 3PT ASSEMBL Y ...

  • Tiger Products Co., Ltd 6020009 - page 123

    Twin Rotary Common Section 6-9 ITEM P ART NO. QTY . DESCRIPTION 1 32616 1 RT R Y , 60" DECK, TRR 2 21474A 1 HITCH, 3PT , TRR 3 22059B 1 ADJ ROD, TRR 4 25095A 1 FRAME, CASTER WHEEL, TRR 60" 5 22057 1 SPINDLE, CASTER AXLE, ASSY 6 21925 4 HEX NUT ,1" NC 7 22023 5 F L A T W ASHER,1" 8 22058 1 SPRING , REAR RTR Y 9 22753 1 TUBE, PROT ...

  • Tiger Products Co., Ltd 6020009 - page 124

    Twin Rotary Common Section 6-10 REAR ROT AR Y HYDRAULICS ...

  • Tiger Products Co., Ltd 6020009 - page 125

    Twin Rotary Common Section 6-11 REAR ROT AR Y HYDRAULICS ITEM P ART NO. QTY . DESCRIPTION 1 23003 1 REAR RTR Y , 60"W/REAR CHAINS 1 30806 1 RT R Y , 60” CPL T - HP (W/FBAR) TRR 2 06510083 1 V A L VE,BRAKE,SOL,3000PSI,METRI 3 33555 4 ADAPTER,1MORB x 1MJIC 4 TF4852 2 K I T , FLANGE, #20 5 34198 1 HOSE, 1" x 40" (1FJX x 20FLG90) 6 341 ...

  • Tiger Products Co., Ltd 6020009 - page 126

    Twin Rotary Common Section 6-12 60” ROT AR Y MOT OR ...

  • Tiger Products Co., Ltd 6020009 - page 127

    Twin Rotary Common Section 6-13 60” ROT AR Y MOT OR ITEM P ART NO. QTY . DESCRIPTION * 06504016 A V AIL MO TO R ASSEMBL Y 1 1/4” COMPLETE TSR/TRAILKA T 1 22790 1 SHAFT END COVER 2 06504025 1 PORT END COVER 3 02962194 1 GEAR HOUSING 4 06504053 1 M A TCHED GEAR SET 5 02962197 4 CAP SCREW 6 06504027 2 SET SCREW 7 06504028 1 K E Y 8 02962201 4 DOWE ...

  • Tiger Products Co., Ltd 6020009 - page 128

    Twin Rotary Common Section 6-14 PUMP - SERVICE P ARTS (06504002) ...

  • Tiger Products Co., Ltd 6020009 - page 129

    Twin Rotary Common Section 6-15 PUMP - SERVICE P ARTS (06504002) ITEM P/N QTY . DESCRIPTION 1 22766 1 HOUSING ,SEC 2 06504068 1 HOUSING ,PEC 3 02965092 2 HOUSING ,GEAR 4 06504069 1 HOUSING ,BEARINGCARRIER 1 0 06504070 1 S ET ,GEARSHAFT 1 2 06504071 1 GEAR,SET 1 5 02961917 4 WASHER 1 6 06504072 4 STUD 1 7 06504073 4 NU T ,HEX 2 1 * 22765 (SEE SEAL K ...

  • Tiger Products Co., Ltd 6020009 - page 130

    Twin Rotary Common Section 6-16 2 SP HUSCO - LOAD SENSE (31320) ...

  • Tiger Products Co., Ltd 6020009 - page 131

    Twin Rotary Common Section 6-17 2 SP HUSCO - LOAD SENSE (31320) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 N/A - N/A 8 6T4209 1 RELI ...

  • Tiger Products Co., Ltd 6020009 - page 132

    Twin Rotary Common Section 6-18 2 SP HUSCO - LOAD SENSE (31321) ...

  • Tiger Products Co., Ltd 6020009 - page 133

    Twin Rotary Common Section 6-19 2 SP HUSCO - LOAD SENSE (31321) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF V AL VE, 360 PSI 7 N/A - N/A 8 6T42 ...

  • Tiger Products Co., Ltd 6020009 - page 134

    Twin Rotary Common Section 6-20 3 SP HUSCO - LOAD SENSE CABLE (06502043) ...

  • Tiger Products Co., Ltd 6020009 - page 135

    Twin Rotary Common Section 6-21 3 SP HUSCO - LOAD SENSE CABLE (06502043) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) (REMOVE S ...

  • Tiger Products Co., Ltd 6020009 - page 136

    Twin Rotary Common Section 6-22 3 SP HUSCO - LOAD SENSE COMBO (06502044) ...

  • Tiger Products Co., Ltd 6020009 - page 137

    Twin Rotary Common Section 6-23 3 SP HUSCO - LOAD SENSE COMBO (06502044) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) (REMOVE S ...

  • Tiger Products Co., Ltd 6020009 - page 138

    Twin Rotary Common Section 6-24 SIDE COOLER ...

  • Tiger Products Co., Ltd 6020009 - page 139

    Twin Rotary Common Section 6-25 SIDE COOLER ITEM PART NO. QTY. DESCRIPTION 1 21530 1 0 CAPSCREW ,1/4 X1 NC 2 21986 1 0 LOCKWASHER,1/4 3 22014 1 0 F L A T W ASHER,1/4 4 35176 1 0 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 M NT ,COOLER,BUMPER T ANK,RH 7 06380007 1 M NT ,COOLER,BUMPER T ANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CAPSCR ...

  • Tiger Products Co., Ltd 6020009 - page 140

    Twin Rotary Common Section 6-26 ITEM P ART NO. QTY . DESCRIPTION 1 REF . * REAR RTR Y - REFER TO REAR R TRY DECK ASSY 2 2851 1 1 REAR RTRY ST AND 3 TB1033D 2 PIN,CLEVIS 1"X4"(DRILLED7/32) 4 6T3014 3 ROLL PIN, 1/4" x 2" 5 6T3004 1 R-CLIP (HAIRPIN COTTER, 3/16") SAFETY ST AND ...

  • Tiger Products Co., Ltd 6020009 - page 141

    Twin Rotary Common Section 6-27 CASTER WHEEL ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 21459 1 SPINDLE, CASTER WHEEL AXLE 2 21987 5 LOCKWASHER, 5/16” 3 21575 5 HEX NUT , 5/16” 4 8548 5 CAPSCREW , 5/16” x 3/4”, NC 5 22697-1 1 RIM, OUTER/RR RTR Y CASTER ASSY 6 21416 1 TIRE,SOLID,RR-RTRY 7 22696-1 1 RIM,REAR ROT ARY CASTER 8 22070 1 DUST CA ...

  • Tiger Products Co., Ltd 6020009 - page 142

    Twin Rotary Common Section 6-28 BRAKE V AL VE ASSEMBL Y W/ METRI P AK ITEM PART NO. QTY. DESCRIPTION 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34095 1 RELIEF VALVE, 3500 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI ...

  • Tiger Products Co., Ltd 6020009 - page 143

    Twin Rotary Common Section 6-29 SWITCHBOX SER VICE P ARTS ITEM P / N Q TY . DESCRIPTION 1 0651401 1 1 SWBX,ALUM,BLK,06510097 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 06510028 1 SWITCH,FORWARD/BRAKE/REV 4 3381 1 2 SWITCH,MASTER/DECK FLOA T 5 6T3923 2 INDICT A TOR LIGHT ,ON,RED 6 34540 2 S T RAIN RELIEF ,3/4,BLACK,NYLON 7 06514006 1 BREAKER,15A,SWBX 8 065 ...

  • Tiger Products Co., Ltd 6020009 - page 144

    Twin Rotary Common Section 6-30 SWITCHBOX SCHEMA TIC ...

  • Tiger Products Co., Ltd 6020009 - page 145

    W ARRANTY SECTION Warranty Section 7-1 ...

  • Tiger Products Co., Ltd 6020009 - page 146

    . ...

  • Tiger Products Co., Ltd 6020009 - page 147

    W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrant s to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the f ...

  • Tiger Products Co., Ltd 6020009 - page 148

    ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an ...

  • Tiger Products Co., Ltd 6020009 - page 149

    T O THE OWNER / OPERA TOR / DEALER T o keep your implement running efficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health Ac ...

  • Tiger Products Co., Ltd 6020009 - page 150

    Printed in USA © T iger Corporation ...

Manufacturer Tiger Products Co., Ltd Category Lawn Mower

Documents that we receive from a manufacturer of a Tiger Products Co., Ltd 6020009 can be divided into several groups. They are, among others:
- Tiger Products Co., Ltd technical drawings
- 6020009 manuals
- Tiger Products Co., Ltd product data sheets
- information booklets
- or energy labels Tiger Products Co., Ltd 6020009
All of them are important, but the most important information from the point of view of use of the device are in the user manual Tiger Products Co., Ltd 6020009.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Tiger Products Co., Ltd 6020009, service manual, brief instructions and user manuals Tiger Products Co., Ltd 6020009. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Tiger Products Co., Ltd 6020009.

Similar manuals

A complete manual for the device Tiger Products Co., Ltd 6020009, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Tiger Products Co., Ltd 6020009 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Tiger Products Co., Ltd 6020009.

A complete Tiger Products Co., Ltd manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Tiger Products Co., Ltd 6020009 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Tiger Products Co., Ltd 6020009, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Tiger Products Co., Ltd 6020009, that we can find in the current document
3. Tips how to use the basic functions of the device Tiger Products Co., Ltd 6020009 - which should help us in our first steps of using Tiger Products Co., Ltd 6020009
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Tiger Products Co., Ltd 6020009
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Tiger Products Co., Ltd 6020009 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Tiger Products Co., Ltd 6020009?

Use the form below

If you did not solve your problem by using a manual Tiger Products Co., Ltd 6020009, ask a question using the form below. If a user had a similar problem with Tiger Products Co., Ltd 6020009 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)