English dropdown-ico

Manual APC SmartSlot Series

17 pages 1.39 mb
Download

Go to site of 17

Summary
  • APC SmartSlot Series - page 1

    Thank Y ou! Thank y ou for selectin g the American Power Conversion SmartSlot Series Measure-UPS II . It has been desi g ned for man y y ears of reliable, mainte- nance-free service. Please read this manual! It provides installation and operatin g instructions that will help y ou g et the most from y our accessor y . Save this manual! It includes i ...

  • APC SmartSlot Series - page 2

    Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3 Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Sensor Zone Connections . . . . . . . . . . ...

  • APC SmartSlot Series - page 3

    1. Introduction The SmartSlot Measure-UPS II performs temperature and humidit y sensin g , as well as contact monitorin g . Measure-UPS II supports up to four zones of contact monitorin g , each of which supports both normall y open and normall y closed contacts. Measure-UPS II reports temperatures from 0 to 60 °C (32 to 140 °F) and relative humi ...

  • APC SmartSlot Series - page 4

    Safety Notice The SmartSlot Measure-UPS II UPS accessor y is intended solel y for use in supplementar y surveillance of equipment. APC does not recom- mend this product for life or propert y protection. APC will not know- in g l y sell Measure-UPS II for use in such applications. APC disclaims all liabilit y arisin g out of improper use of Measure- ...

  • APC SmartSlot Series - page 5

    2. Installation Use the followin g procedure to install SmartSlot Measure-UPS II : 1. Install and configure an y software or hardware that will be used with Measure-UPS II for data reporting (see software and hard- ware compatibility abov e). 2. Using figure 2 as a guide, install Measure-UPS II in the host SmartSlot. Use a #2 Phillips head screwdri ...

  • APC SmartSlot Series - page 6

    Do not: • Cov er any of the ventilation holes on the probe • Immerse the probe or place it where de w can be expected to form • Use the probe in an en vironment with chlorine gas or insecti- cides. 5. The contact monitoring connection is a two piece design. Connect contact closure-type sensors to the remov able scre w terminal block using the ...

  • APC SmartSlot Series - page 7

    3. Operation Check 1. Confirm the basic operation of Measure-UPS II . Use the data reporting system (see hardware and software compatibility in sec- tion 1) to confirm that Measure-UPS II is w orking. W ith the probe (temperature or temperature and humidity) connected to probe connector 1, Measure-UPS II should transmit temperature or tem- perature ...

  • APC SmartSlot Series - page 8

    4. Sensor Zone Connections Connection Information Measure-UPS II supports normall y open and normall y closed loop s y stems, and allows mixin g of normall y open and normall y closed sensors on an y zone. See the fi g ures below for more information on usin g multiple sensors in one zone and for s y stem hookup. Note: Do not cross connect sensors ...

  • APC SmartSlot Series - page 9

    In order to avoid receivin g alarm indications on unused zones, install a j umper wire between the COM and NC connectors for each unused zone. T o use more than one sensor on a zone, follow the dia g ram below . Connect normall y open sensors in parallel and normall y open sensors in series. ...

  • APC SmartSlot Series - page 10

    See below for a t y pical hookup. Note that in this example s y stem zone 1 is a normall y closed motion zone with power for the passive infrared detector supplied b y Measure-UPS II . Zone 2 is a normall y open zone. Zone 3 is a combination normall y open and normall y closed zone. Zone 4 is not used. ...

  • APC SmartSlot Series - page 11

    5. Sensor Selection Measure-UPS II ma y be used with an y dr y contact closure t y pe sen- sors. The Measure-UPS II sensor inputs are desi g ned to monitor cir- cuits that have no volta g e potential of their own. Connection of Measure-UPS II sensor inputs to an y circuit other than a dr y closure t y pe will void the warrant y and ma y r e su l t ...

  • APC SmartSlot Series - page 12

    6. Maintenance Measure-UPS II requires periodic maintenance. Confirm contact sens- in g usin g the sensor manufacturers recommended intervals and meth- ods. Use the data reportin g s y stem to verif y that each sensor operates as planned. Clean the temperature (or temperature and humidit y ) probe whenever there is a visible buildup of dust. Gentl ...

  • APC SmartSlot Series - page 13

    7. T roubleshooting Problem Possible Cause Solution Constant Alarm on one or more unused zones. Unused zones not jumpered. Connect a wire between the COM and NC terminals of all unused zones (see section 4). Constant low tem- perature and humid- ity readings. 12 Vdc supply (pin 1) shorted to ground or overloaded. Correct short circuit — examine a ...

  • APC SmartSlot Series - page 14

    8. Service If the SmartSlot Measure-UPS II requires service: 1. Check Measure-UPS II using the troubleshooting chart in section 7 before calling for service. 2. Note the model number of the Measure-UPS II , the serial number , and the date purchased. See the back cov er of this manual for the correct telephone number and call customer service. A te ...

  • APC SmartSlot Series - page 15

    9. Specifications Electrical SmartSlot specification compatible Operatin g volta g e: 16 - 27 Vdc Operatin g current draw: 30 mAdc (exclusive of an y attached sensors) T emperature accurac y : ±2° C (± 3.6° F), from 0 to 40° C (32 to 104° F) Humidit y accurac y : ±8% RH, 10 to 90% RH, at 25° C (77° F); ±8% RH, 30 to 80% RH, from 15 to 30? ...

  • APC SmartSlot Series - page 16

    10. Declaration of Conformity Application of Council Directives: 89/336/EEC Standards to Which Conformit y is Declared: EN55022, EN50082-1 Manufacturers Name: American Power Conversion 132 Fair g rounds Road We s t K i n g ston, RI 02892 USA Importer ’ s Name and Address: T y pe of Equipment: Measure-UPS II Model Number: AP9612T , AP9612TH Serial ...

  • APC SmartSlot Series - page 17

    Limited W arranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obli- gation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. T o obtain service under warranty you must o ...

Manufacturer APC Category Power Supply

Documents that we receive from a manufacturer of a APC SmartSlot Series can be divided into several groups. They are, among others:
- APC technical drawings
- SmartSlot Series manuals
- APC product data sheets
- information booklets
- or energy labels APC SmartSlot Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual APC SmartSlot Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals APC SmartSlot Series, service manual, brief instructions and user manuals APC SmartSlot Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product APC SmartSlot Series.

Similar manuals

A complete manual for the device APC SmartSlot Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use APC SmartSlot Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of APC SmartSlot Series.

A complete APC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual APC SmartSlot Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the APC SmartSlot Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the APC SmartSlot Series, that we can find in the current document
3. Tips how to use the basic functions of the device APC SmartSlot Series - which should help us in our first steps of using APC SmartSlot Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with APC SmartSlot Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of APC SmartSlot Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning APC SmartSlot Series?

Use the form below

If you did not solve your problem by using a manual APC SmartSlot Series, ask a question using the form below. If a user had a similar problem with APC SmartSlot Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)