English dropdown-ico

Manual Omega Engineering LVCN700 Series

10 pages 0.37 mb
Download

Go to site of 10

Summary
  • Omega Engineering LVCN700 Series - page 1

    http://www .omega.com e-mail: info@omega.com ® U ser’s Guide L VCN700 S er i es Multi-Point Ultrasonic Level Switch WARRANTY /DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OM EGA Warranty adds an additional one (1) month grace period to th ...

  • Omega Engineering LVCN700 Series - page 2

    Step One SPECIFICA TIONS Range: L VCN704: 2" to 4' (5 cm to 1.2m) L VCN709: 4" to 9.8' (10 cm to 3m) L VCN716: 4" to 16.4' (10 cm to 5m) L VCN126: 8" to 26.2' (20 cm to 8m) Repeatability: 0.25" (6 mm) Adjustability: Over entire range Hysteresis: L VCN704/709: 0.5" (1.2 cm) (single set point) L VCN71 ...

  • Omega Engineering LVCN700 Series - page 3

    INTR ODUCTION TECHNOLOGY Step Three A. Application: The general purpose ultrasonic level switch pro- vides non-contact level detection up to 26’ or 8m with 3 relays. Each relay can be configured on a single set point alarm, two latched set points for automatic fill or empty , two set points for out of bounds alarms or three set point (relays 1 an ...

  • Omega Engineering LVCN700 Series - page 4

    Step Four Step Five CALIBRA TION A. Introduction: The switch has two modes, the RUN and CAL modes. In the RUN mode, the switch is operational and the relay(s) will energize or de-ener gize at the calibrated set point distances. In the CAL mode, the relay set point distances and states may be target-cal- ibrated into memory . The switch arrives from ...

  • Omega Engineering LVCN700 Series - page 5

    Step Seven Step Six CALIBRA TION B. Calibration T ools: T o target calibrate the switch set points, you will need the appropriate power supply (95-250 V AC or 12-28 VDC for DC version), tape measurer , flat reflective target such as a wall, and optional Omega box insert for use as a product holder . C. Off T ank T arget Calibration: The switch’ s ...

  • Omega Engineering LVCN700 Series - page 6

    Step Eight PR OGRAMMING Step Nine PR OGRAMMING C. Programming a High and Low Level Out of Bounds Alarm: After having powered the switch with the appropriate supply voltage, entered the CAL mode, selected a relay channel and erased any previously input set points, follow the below procedure: 1. Stretch the tape measurer out to the appropriate distan ...

  • Omega Engineering LVCN700 Series - page 7

    Step T en PR OGRAMMING E. Programming A utomatic Empty: After having powered the switch with the appropriate supply voltage, entered the CAL mode, selected a relay channel and erased any previously input set points, follow the below procedure: 1. Stretch the tape measurer out to the appropriate distance in between the switch and target. 2. Position ...

  • Omega Engineering LVCN700 Series - page 8

    A. Fitting Selection: Check the switch part number to determine the required fitting mount size and thread type. The switch is commonly installed in tank adapters, flanges, brackets or stand pipes. 1. Adapter : Select a tank adapter fitting with minimal height so as to ensure that the installed transducer will not be substantially elevated into the ...

  • Omega Engineering LVCN700 Series - page 9

    Step Fourteen High Alarm VA C INPUT HOT NEUTRAL Motor Starter (Pump) RELA Y 1 RELA Y 2 RELA Y 3 L 1 L 2 POWER VA C Cal. Run High Low Select Low Alarm VA C INPUT NEUTRAL HOT High Alarm VDC INPUT HOT NEUTRAL Motor Starter (Pump) RELA Y 1 RELA Y 2 RELA Y 3 (+) (-) POWER VDC Cal. Run High Low Select Low Alarm VDC INPUT NEUTRAL HOT WIRING Step Fifteen T ...

  • Omega Engineering LVCN700 Series - page 10

    Relay 1 Relay 2 Energize De-Energize Energize De-Energize Backup Primary Stop Relay 1 Relay 2 Energize De-Energize Energize De-Energize Backup Primary Stop Duplexing Control Operation Alternating Control Operation OPERA TION Step Sixteen Relay X Energize De-Energize Start Stop A utomatic Empty Operation A utomatic Fill Operation Out of Bounds Opera ...

Manufacturer Omega Engineering Category Switch

Documents that we receive from a manufacturer of a Omega Engineering LVCN700 Series can be divided into several groups. They are, among others:
- Omega Engineering technical drawings
- LVCN700 Series manuals
- Omega Engineering product data sheets
- information booklets
- or energy labels Omega Engineering LVCN700 Series
All of them are important, but the most important information from the point of view of use of the device are in the user manual Omega Engineering LVCN700 Series.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Omega Engineering LVCN700 Series, service manual, brief instructions and user manuals Omega Engineering LVCN700 Series. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Omega Engineering LVCN700 Series.

Similar manuals

A complete manual for the device Omega Engineering LVCN700 Series, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Omega Engineering LVCN700 Series by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Omega Engineering LVCN700 Series.

A complete Omega Engineering manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Omega Engineering LVCN700 Series - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Omega Engineering LVCN700 Series, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Omega Engineering LVCN700 Series, that we can find in the current document
3. Tips how to use the basic functions of the device Omega Engineering LVCN700 Series - which should help us in our first steps of using Omega Engineering LVCN700 Series
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Omega Engineering LVCN700 Series
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Omega Engineering LVCN700 Series in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Omega Engineering LVCN700 Series?

Use the form below

If you did not solve your problem by using a manual Omega Engineering LVCN700 Series, ask a question using the form below. If a user had a similar problem with Omega Engineering LVCN700 Series it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)