English dropdown-ico

Manual Weider WESY49201

35 pages 1.03 mb
Download

Go to site of 35

Summary
  • Weider WESY49201 - page 1

    QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory . TO A VOID UNNECESSAR Y DELA YS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The t ...

  • Weider WESY49201 - page 2

    1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions. 3. The weight system is intended for home use only . Do not use the weight system in any commercial, rental, o ...

  • Weider WESY49201 - page 3

    3 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. Width: 86 in. Length: 66 in. Foot Plate High Pulley Station Lat Bar Leg Lever Butterfly Arms Assist Arm Press Arm Weight Stacks Backrests Dip Handles Pull-up Handles W arning Decal 1 W arning Decal 1 W arning Decal 3 W arning Decal 2 Leg Press Plate Thank you for selecting the versatile CLUB W ...

  • Weider WESY49201 - page 4

    4 ASSEMBL Y 1 8 8 11 51 27 1 4 3 1 51 5 1. Before beginning assembly , be sure that you have read and understand the infor- mation in the box above. Locate and open the parts bag labeled “FRAME ASSEMBL Y .” Press two 2” Square Outer Caps (51) onto the Stabilizer (5). Press a 2” Square Inner Cap (27) into the Base (4). Insert six 5/16” x 2 ...

  • Weider WESY49201 - page 5

    5 2. Slide the Assist Upright (74) and the Leg Press Upright (56) onto the indicated 5/16” x 2 1/2” Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the Assist Upright and Leg Press Upright should be on the side shown. Hand-tighten four 5/16” Nylon Locknuts (3) onto the Carriage Bolts. Do not tighten the Nylon Locknu ...

  • Weider WESY49201 - page 6

    6 4. Press a 2” Square Inner Cap (27) into the end of the T op Frame (55). Press a 1 3/4” Square Inner Cap (44) into each end of the crossbar on the T op Frame. Press two 1” Inner Caps (1 13) into the top of the crossbar . Attach the T op Frame (55) to the Assist Upright (74) and the Leg Press Upright (56) with two 5/16” x 2 3/4” Bolts (1 ...

  • Weider WESY49201 - page 7

    7 7. Press a Weight T ube Bumper (64) into the end of the Short Weight T ube (108). Insert the Weight T ube into the front stack of Weights (25). Be sure that the pin on the Weight T ube is sitting in the pin groove in the top Weight. Lubricate the inside of the holes in a T op Weight (65). Set the T op Weight onto the front stack of Weights (25). ...

  • Weider WESY49201 - page 8

    8 9. Attach the upper ends of the Short Weight Guides (73) to the T op Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and a 5/16” Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the T op Frame (55) in the same manner . 10. Locate and open the parts bag labeled “ARM ASSEMBL Y .” Make su ...

  • Weider WESY49201 - page 9

    9 12. Press a 1” Round Inner Cap (49) into one of the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner . 13. Identify the Right Arm ...

  • Weider WESY49201 - page 10

    10 15. See the inset drawing. Attach the Military Press Arm (84) to the Pivot Arm (101) with two 5/16” x 2 1/4” Bolts (33) and two 5/16” Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the Military Press Arm (84). Press two 1” Round Inner Caps (49) into the Military Press Arm. Attach the Pivot Arm (101) to the Assist Upri ...

  • Weider WESY49201 - page 11

    11 17. Attach the Left Pull-up Arm (75) and the Right Pull-up Arm (77) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Attach the Left Dip Arm (78) and the Right Dip Arm (79) to the Assist Upright (74) with two 5/16” x 2 3/4” Bolts (1 1) and two 5/16” Nylon Locknuts (3). Wet the end of th ...

  • Weider WESY49201 - page 12

    12 20. W rap the High Cable (58) around a “V”-Pulley (50). Attach the Pulley and a Long Cable T rap (31) to the indicated bracket on the Front Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the Long Cable T rap is positioned to hold the Cable in place. 21. Route the High Cable (58) around the “V? ...

  • Weider WESY49201 - page 13

    13 24. See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable T rap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable T rap is inside the Long “U”- Bracket. Note: This may come pre-assem- bled. Route the High Cable (58) through the Long “U”- ...

  • Weider WESY49201 - page 14

    14 27. Locate the Low Cable (23). Route the Low Cable under the 3 1/2” Low Pulley (102). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame. T ighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (not shown). 2 ...

  • Weider WESY49201 - page 15

    15 31. Attach the end of the Low Cable (23) to the Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the Nylon Locknut, as shown in the inset drawing. 32. Attach the High Cable ...

  • Weider WESY49201 - page 16

    16 34. W rap the Military Press Cable (72) around a “V”-Pulley (50). Attach the Pulley to the T op Frame (55) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley to the indicated bracket on the Assist Arm (105) with a 3/8” x 1 3/4” Bolt (76) ...

  • Weider WESY49201 - page 17

    17 36. Slide a 5/16” W asher (8) onto a 5/16” x 2 3/4” Bolt (1 1). Insert the Bolt through the indicated hole in the Pivot Arm (101). The Bolt must be inserted from the side shown. Fully tight- en a 5/16” Nylon Jamnut (93) onto the Bolt. Wrap the Military Press Cable (72) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable T rap (6 ...

  • Weider WESY49201 - page 18

    18 38. Locate the Leg Press Cable (99). Attach the end of the Leg Press Cable to the Long “U”- Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” W asher (10). Do not completely tight- en the Nylon Locknut. It should be thread- ed onto the end of the Cable only a couple of turns, as shown in the inset drawing. Wrap the Leg Press Cable (9 ...

  • Weider WESY49201 - page 19

    19 40. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Insert a 1/4” x 2 1/2” Carriage Bolt (92) through the center hole in a Seat Plate (37). Attach the Seat Plate to the Rear Backrest (85) with two 1/4” x 3/4” Screws (18). Insert the 1/4” x 2 1/2” Carriage Bolt (92) through the indicated hole in the Leg Press Upright (56 ...

  • Weider WESY49201 - page 20

    20 43. Attach the Front Backrest (41) to the Front Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” W ashers (10). The Backrest must be oriented as shown. 44. Press a 1 1/2” Square Inner Cap (32) into the Front Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) through the center hole in the Seat Plate (37). Attach the S ...

  • Weider WESY49201 - page 21

    47. Press two 3/4” Round Inner Caps (34) into each Pad T ube (28). Insert a Pad T ube (28) into the Front Seat Frame (36). Slide a Foam Pad (30) onto each end of the Pad T ube. Insert the other Pad T ube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto each end of the Pad T ube. 48. Remove the backing from the CLUB WEIDER 16.6ST deca ...

  • Weider WESY49201 - page 22

    22 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPOR- T ANT : When attaching the lat bar or nylon strap, make sure that the attachments are in the correct start- ing position for t ...

  • Weider WESY49201 - page 23

    23 A TT ACHING AND REMOVING THE SEA T T o attach the Seat (13), set the bracket on the Front Seat Frame (36) onto the indicated pins on the Front Upright (42). Attach the Front Seat Frame to the Front Upright with the 5/16” x 2 3/4” Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be sure that ...

  • Weider WESY49201 - page 24

    24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lbs. top weight. The other numbers refer to the 12.5 lbs. weight plates. The butterfly arm resistance listed is the resis- tance for each butterfly arm. WEIGHT PRESS BUTTERFL Y LEG HIGH LOW MILIT AR Y LEG ASSIST ARM AR ...

  • Weider WESY49201 - page 25

    TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi- ately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight system, can stretch ...

  • Weider WESY49201 - page 26

    26 CABLE DIAGRAMS The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly . If the cables have not been correctly routed, the weight system will ...

  • Weider WESY49201 - page 27

    27 Military Press Cable (72) Leg Press Cable (99) Rear Weight Stack— 1 2 3 4 7 6 5 3 2 4 — Rear Seat Frame 8 — Pivot Arm 1 — Long “U”-Bracket Military Press Cable (72) and Leg Press Cable (99) ...

  • Weider WESY49201 - page 28

    ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1. The MODEL NUMBER of the product (WESY49201) 2. The NAME ...

  • Weider WESY49201 - page 29

    Note: The assembly is divided into four stages: 1) frame assembly , 2) arm assembly , 3) cable assembly , 4) seat assembly . The hardware for each stage is packaged separately . W AIT UNTIL YOU BEGIN EACH ASSEMBL Y ST AGE TO OPEN THE P ARTS BAG LABELED FOR THA T ASSEMBL Y ST AGE. This chart is provided to help you identify the small parts used in a ...

  • Weider WESY49201 - page 30

    5/16" Nylon Locknut (3) 1/4" W asher (10) 5/16" W asher (8) 1" Retainer (69) 3/8" W asher (9) 1/4" x 2 1/2" Screw (43) 3/8" Nylon Locknut (21) 1/4" x 2" Machine Screw (81) 5/16" Nylon Jamnut (93) 1/4" x 2 1/2" Carriage Bolt (92) 1/4" x 2" Carriage Bolt (38) 5/16" x 2 1/ ...

  • Weider WESY49201 - page 31

    5/16" x 2 3/4" Carriage Bolt (14) 3/8" x 3 1/2" Bolt (16) 5/16" x 5" Bolt (68) 3/8" x 3 3/4" Bolt (88) 3/8" x 8" Bolt (59) 5/16" x 6" Bolt (60) 5/16" x 2 3/4" Bolt (1 1) 3/8" x 3 1/4" Bolt (67) #8 x 1/2" Self-tapping Screw (87) 5/16" x 1 3/4" Bolt (24) 5/ ...

  • Weider WESY49201 - page 32

    1" Round Inner Cap (49) 3/4" Round Inner Cap (34) 1/2" x 3/4" Spacer (61) 5/8" x 9/16" Spacer (7) 1 1/4" Round Inner Cap (109) 1" Round Cover Cap (70) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 2" Square Inner Cap (27) 2" Square Outer Cap (51) 1" Square Inner Cap (6) 1& ...

  • Weider WESY49201 - page 33

    8 1 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THIS P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE ...

  • Weider WESY49201 - page 34

    P ART LIST—Model No. WESY49201 R0602A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty . Description 1 10 5/16” x 2 1/2” Carriage Bolt 2 6 1/4” Nylon Locknut 3 35 5/16” Nylon Locknut 4 1 Base 5 1 Stabilizer 6 1 1” Square Inner Cap 7 1 5/8” x 9/16” Spacer 8 8 5/16” Was ...

  • Weider WESY49201 - page 35

    60 27 21 50 55 86 11 8 15 12 44 88 15 58 21 44 21 3 61 62 24 3 58 71 2 65 108 64 25 26 19 9 3 3 49 6 22 46 46 16 3 9 15 21 59 23 21 17 27 1 4 10 43 41 42 21 3 50 31 86 70 69 69 70 21 47 44 45 44 45 48 50 31 86 13 40 38 37 18 32 34 30 28 3 49 83 33 10 2 36 14 15 29 35 30 34 34 30 28 21 9 32 30 34 10 11 3 11 3 81 88 44 44 83 66 66 66 90 89 89 7 3 1 1 ...

Manufacturer Weider Category Home Gym

Documents that we receive from a manufacturer of a Weider WESY49201 can be divided into several groups. They are, among others:
- Weider technical drawings
- WESY49201 manuals
- Weider product data sheets
- information booklets
- or energy labels Weider WESY49201
All of them are important, but the most important information from the point of view of use of the device are in the user manual Weider WESY49201.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Weider WESY49201, service manual, brief instructions and user manuals Weider WESY49201. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Weider WESY49201.

Similar manuals

A complete manual for the device Weider WESY49201, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Weider WESY49201 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Weider WESY49201.

A complete Weider manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Weider WESY49201 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Weider WESY49201, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Weider WESY49201, that we can find in the current document
3. Tips how to use the basic functions of the device Weider WESY49201 - which should help us in our first steps of using Weider WESY49201
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Weider WESY49201
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Weider WESY49201 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Weider WESY49201?

Use the form below

If you did not solve your problem by using a manual Weider WESY49201, ask a question using the form below. If a user had a similar problem with Weider WESY49201 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)