-
Linak MEDLINE MJB - page 1
T o learn more about LINAK please visit: WWW .LINAK.COM MJB - Gateway USER MANUAL ...
-
Linak MEDLINE MJB - page 2
2 ...
-
Linak MEDLINE MJB - page 3
Contents Preface .............................................................................................................................. .................................... 4 Important information .............................................................................................................................. .......... 5 Safet ...
-
Linak MEDLINE MJB - page 4
Pr eface We ar e delighted that you have chosen a product fr om LINAK ® . LINAK systems are high-tech pr oducts based on many years of experience in the manufacture and development of actuators, electric contr ol boxes, controls and chargers. This User Manual will tell you how to install, use and maintain your LINAK equipment. We ar e sure that yo ...
-
Linak MEDLINE MJB - page 5
5 Safety instructions Safe use of the system is possible only when the operating instructions are r ead completely and the instructions contained are strictly observed. Failure to comply with instructions marked with the”NOTE” symbol may r esult in serious damage to the system or one of its components. Persons who do not have the necessary expe ...
-
Linak MEDLINE MJB - page 6
Residual risk Some of the products contains softwar e based components. LINAK has made various possible efforts to assur e that the software is fr ee of errors and that the software has been developed accor ding to the rules of IEC 60601-1-4 (software in Medical pr oducts). That involves Risk Analysis which shows a small residual risk for unwanted/ ...
-
Linak MEDLINE MJB - page 7
7 Before installation, r e-installation, or troubleshooting • Stop the application • Switch off the power supply and pull out the mains plug. • Relieve the application of any loads, which may be released during the work. Before start-up • Make sure that the system has been installed as instructed in the User Manual. • Make sure that the v ...
-
Linak MEDLINE MJB - page 8
8 Repairs In order to avoid the risk of malfunction, all r epairs must only be carried out by authorised LINAK workshops or repair ers, as special tools must be used and special gaskets must be fi tted. Products under warranty must also be r etur ned to authorised LINAK workshops. W ar ning! If any of the LINAK products ar e opened, there will be ...
-
Linak MEDLINE MJB - page 9
9 Misc. on the MJB system W arranty and service life The LINAK warranty covers manufacturing defects in the pr oducts, starting from the date of manufacture. Ther e is 18 months’ warranty for MEDLINE and CARELINE products. The warranty is limited to the value of the LINAK pr oduct. LINAK’ s guarantee is only valid so far as the products have be ...
-
Linak MEDLINE MJB - page 10
10 MJB - GA TEW A Y variant, 504-01 & 504-02 : The MJB is a simple gateway interface, which can connect the bed to the infrastructure of the hospital or nursing homes. The Gateway can be used in combination with an Out of Bed Sensor , which makes it possible to indicate if the patient leaves the bed. The Gateway can also be used as a service/nu ...
-
Linak MEDLINE MJB - page 11
11 Features: • Add-on value for hospital & care bed • Compact and functional design which allows easy mounting • 2 connections, Port1 OpenBus™ connection / Port 5 Gateway • Colour: Light grey RAL 7035 • Protection class IPX6 • Connection to OpenBus™ control box via modular plug cable, 6 wir es • Modular plug to Open end, see p ...
-
Linak MEDLINE MJB - page 12
12 Relay 1 CB power mode Alarm level Relay state Mains unplugged, CB is in power down or the OpenBus™ is not running (Clock/ data is missing) Alarm NC* On mains or battery at “wake up” Bed Alarm** NC No Alarm NO Relay 2 CB power mode Alarm level Relay state Mains unplugged or CB is in power down No Alarm NC On mains or battery at “wake up ...
-
Linak MEDLINE MJB - page 13
13 Precautions: • Always use locking mechanism and O-ring • Sockets not used must be fi tted with blind plugs to ensure IP Degr ee • When using the modular plug with open end, is it up to the customer to maintain the IP degree. • If the MJB – Gateway is used as open loop, there is a risk of not sending an alarm, when no mains are connect ...
-
Linak MEDLINE MJB - page 14
14 Cable ordering nos.: Modular plug – open end: 0964140-3000 Please note, the slit is placed on the opposite side of the modular plug. This is to ensure that the cable is only being used for the Gateway MJB. ...
-
Linak MEDLINE MJB - page 15
15 IP Protection Cleaning instrucions IPX0 Clean with a damp cloth IPX1 Clean with a damp cloth IPX2 Clean with a damp cloth IPX3 Clean with a damp cloth IPX4 Clean with a damp cloth IPX5 W ash with a brush and water , but not water under pressur e IPX6 X W ash with a brush and water . The water can be under pressur e, but the system must not be ho ...
-
Linak MEDLINE MJB - page 16
16 W ar ning! The systems must not be sprayed directly with a high-pr essure cleaner . W ar ning! Interconnecting cables must r emain plugged in during cleaning to prevent the ingress of water . Precaution! When cleaned, water must never be sprayed upwar ds from underneath the bed, because it may enter the cable outlet. Envir onmental conditions: E ...
-
Linak MEDLINE MJB - page 17
17 Modular plug with wide slit T o be used with LINAK products. Can be connected to all ports in the MJB, both ports with narrow and wide slit. Modular plug with narr ow slit T o be used with 3 rd party products. Can only be connected to ports in the MJB with narrow slit. This is to pr event 3 rd party products to interfere with the OpenBus TM conn ...
-
Linak MEDLINE MJB - page 18
18 T ype B equipment, as per EN 60601-1 Protection against contact/foreign matter (first character) and water (second character) as per EN60529 Class 2 equipment For indoor use Double insulated transformer Protective earth Alter nating Curr ent Direct curr ent Attention, consult accompanying documents Key to symbols Lock function Release function C ...
-
Linak MEDLINE MJB - page 19
19 Demko approval Fimko approval Australian approval mark Australian approval mark Recognised - Component Mark Canadian Recognised - Component Mark Recognised Component Mark for Canada and the United States T -Mark RW-Tüv approval Tüv .Produkt Service TÜVRheinland ETL C-ETL LGA UL Listing Mark C-UL Listing Mark C-UL US Listing Mark UL Listing Ma ...
-
Linak MEDLINE MJB - page 20
20 MJB MJB - Modular Junction Box DRA WING APPENDIX MJB ...
-
Linak MEDLINE MJB - page 21
21 LINAK APPLICA TION POLICY The purpose of the application policy is to defi ne areas of r esponsibilities in relation to applying a LINAK product defi ned as har dware, softwar e, technical advice, etc. related to an existing or new customer application. LINAK products as defi ned above ar e applicable for a wide range of applications within t ...
-
Linak MEDLINE MJB - page 22
22 ...
-
Linak MEDLINE MJB - page 23
23 ...
-
Linak MEDLINE MJB - page 24
Copyright © LINAK 2010.10 MA-M9-02-348 LINAK A/S reserve the right to make technical alterations T erms of use The user is responsible for determining the suitability of LINAK products for specifi c application. LINAK takes great care in providing accurate and up-to-date information on its products. However , due to continuous development in orde ...
Do you have a question concerning Linak MEDLINE MJB?
Use the form below
If you did not solve your problem by using a manual Linak MEDLINE MJB, ask a question using the form below. If a user had a similar problem with Linak MEDLINE MJB it is likely that he will want to share the way to solve it.