English dropdown-ico

Manual Extron electronic 1600

29 pages 6.65 mb
Download

Go to site of 29

Summary
  • Extron electronic 1600 - page 1

    68-1736-50 Rev . C 08 13 XTP Cr ossPoint 1600 XTP Cr ossPoint 3200 Configurable Digital Video Matrix Switchers Matrix Switchers Setup Guide ...

  • Extron electronic 1600 - page 2

    FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rules. The ClassA limits provide r easonable protection against harmful interfer ence when the equipment is operated in a commercial envir onment. This equipment generates, uses, and can radiate rad ...

  • Extron electronic 1600 - page 3

    XTP CrossPoint 1600 and 3200 • Contents v Contents Introduction ................................1 About this Guide ............................. 1 About the XTP CrossPoint Matrix Switchers ............................ 1 Endpoint Conguration ............... 3 Swapping Boards and Endpoints ................................... 3 Installation ..... ...

  • Extron electronic 1600 - page 4

    XTP CrossPoint 1600 and 3200 • Intr oduction 1 vi XTP CrossPoint 1600 and 3200 • Contents Intr oduction This section gives an overview of the congurable Extron XTP CrossPoint 1600 and XTP Cr ossPoint 3200 Series and describes their features. T opics that are covered include: • About this Guide • About the XTP CrossPoint Matrix Switchers ...

  • Extron electronic 1600 - page 5

    XTP CrossPoint 1600 and 3200 • Intr oduction 2 3 XTP CrossPoint 1600 and 3200 • Intr oduction The XTP CrossPoint models ar e assembled from user -installed and hot-swappable input and output boards. T able 1, on the previous page, identies the four types of input boards and four types of output boar ds currently available, each of which can ...

  • Extron electronic 1600 - page 6

    XTP CrossPoint 1600 and 3200 • Installation 5 4 XTP CrossPoint 1600 and 3200 • Introduction Installation This section describes installation of the XTP CrossPoint matrix switchers, including connections and features. T opics that are covered include: • Rear Panel • Front Panel Rear Panel INPUTS OUTPUTS 100-240V 50-60Hz -- A MAX 1−4 5−8 ...

  • Extron electronic 1600 - page 7

    6 XTP CrossPoint 1600 and 3200 • Installation 7 XTP CrossPoint 1600 and 3200 • Installation Inputs and Outputs a Input boards space — Make connections to installed input boar ds as desired. XTP CP 4i (XTP input board) IN IN XTP CP 4i RS-232 IR Tx Rx Tx Rx RS-232 IR Tx Rx Tx Rx RS-232 IR Tx Rx Tx Rx RS-232 IR Tx Rx Tx Rx SIG LINK XTP PWR LAN X ...

  • Extron electronic 1600 - page 8

    8 XTP CrossPoint 1600 and 3200 • Installation 9 XTP CrossPoint 1600 and 3200 • Installation XTP CP 4i DVI Pro (DVI Pr o input boards) IN XTP CP 4i DVI Pro AUDIO LR LR LR LR IN 1g 1g 1g 1g 1h 1g DVI connectors — Connect up to four DVI cables between these ports and the DVI output port of the digital video sources. 1h Audio (local audio) connec ...

  • Extron electronic 1600 - page 9

    10 XTP CrossPoint 1600 and 3200 • Installation 11 XTP CrossPoint 1600 and 3200 • Installation XTP CP 4o HDMI (HDMI output board) OUT XTP CP 4o HDMI AUDIO LR LR LR LR OUT 2e 2e 2e 2e 2f 2e HDMI connectors — Connect an HDMI video display to each of these ports. NOTE : See HDMI connectors on page 14 to secure the connector to the board with a Lo ...

  • Extron electronic 1600 - page 10

    12 XTP CrossPoint 1600 and 3200 • Installation 13 XTP CrossPoint 1600 and 3200 • Installation Additional Connector Information TP connectors All LAN ports, whether on XTP boards or the switcher Ethernet port use Category (CA T) 5e, CA T 6a, or CA T 7 unshielded twisted pair (UTP) or shielded twisted pair (STP) cables. The XTP ports are compatib ...

  • Extron electronic 1600 - page 11

    14 XTP CrossPoint 1600 and 3200 • Installation 15 XTP CrossPoint 1600 and 3200 • Installation RS-232 and IR connectors Figure 5 shows how to wir e the RS-232 and IR connector . Tx/Rx Pins Rx G Tx RS-232 IR Rx Tx Tx Rx Rx Tx Gnd Gnd IR Device RS-232 Device Figure 5. RS-232 and IR Connector Wiring NOTES: • The length of exposed wires is critica ...

  • Extron electronic 1600 - page 12

    XTP CrossPoint 1600 and 3200 • Fr ont Panel Operations 17 16 XTP CrossPoint 1600 and 3200 • Installation Fr ont Panel Operations This section describes simple XTP CrossPoint matrix switcher operation from the fr ont panel. T opics that are cover ed include: • Creating a Tie • Saving or Recalling a Preset • Setting the Front Panel Locks (E ...

  • Extron electronic 1600 - page 13

    18 XTP CrossPoint 1600 and 3200 • Fr ont Panel Operations 19 XTP CrossPoint 1600 and 3200 • Fr ont Panel Operations Selecting Lock Mode 2 or T oggling Between Mode 2 and Mode 0 NOTES: • If the switcher is in Lock mode 0 or mode 1, this procedur e selects mode 2. The Preset, View , and Esc buttons ash twice. • If the switcher is in Lock m ...

  • Extron electronic 1600 - page 14

    XTP CrossPoint 1600 and 3200 • Remote Contr ol 21 20 XTP CrossPoint 1600 and 3200 • Front Panel Operations Viewing and Adjusting the Audio Level NOTES: • Gain and attenuation can be adjusted for local inputs only . • V olume can be adjusted for the local outputs only . 1. Press and hold the Audio button until it ashes. A UDIO A UDIO Audi ...

  • Extron electronic 1600 - page 15

    22 XTP CrossPoint 1600 and 3200 • Remote Contr ol 23 XTP CrossPoint 1600 and 3200 • Remote Contr ol 2. If necessary , enter the appropriate password. If the password is accepted, the switcher r esponds with Login User or Login Administrator . If the password is not accepted, the Password pr ompt reappears. Number of connections A switcher can h ...

  • Extron electronic 1600 - page 16

    24 XTP CrossPoint 1600 and 3200 • Remote Contr ol 25 XTP CrossPoint 1600 and 3200 • Remote Contr ol SIS Command and Response T able for Matrix Switcher Commands Command SIS Command (Host to Unit) Response (Unit to Host) Additional Description Create ties NOTES : • Commands can be entered back-to-back in a string, with no spaces. For example: ...

  • Extron electronic 1600 - page 17

    26 XTP CrossPoint 1600 and 3200 • Remote Contr ol 27 XTP CrossPoint 1600 and 3200 • Remote Contr ol NOTE : X! = Input number 01 – 16 or 32 X% = Picture adjustments 0 through 255 Command SIS Command (Host to Unit) Response (Unit to Host) Additional Description Tint (available for inputs on an XTP CP 4i VGA universal analog input board only) NO ...

  • Extron electronic 1600 - page 18

    28 XTP CrossPoint 1600 and 3200 • Remote Contr ol 29 XTP CrossPoint 1600 and 3200 • Remote Contr ol NOTE : X! = Input number 01 – 16 or 32 X@ = Output number 01 – 16 or 32 X& = Analog input preset 1 through 8 X* = HDCP status (for inputs) 0 = no source connected 1 = source is HDCP compliant 2 = source is not HDCP compliant X( = HDCP sta ...

  • Extron electronic 1600 - page 19

    30 XTP CrossPoint 1600 and 3200 • Remote Contr ol 31 XTP CrossPoint 1600 and 3200 • Remote Contr ol Command SIS Command (Host to Unit) Response (Unit to Host) Additional Description Audio output volume Set the volume to a specic value X@ * X1% V Out X@ • Vol X1%] Example: 1*50v Out01 • Vol50 ] Set output 1 volume to 79%. Increment volume ...

  • Extron electronic 1600 - page 20

    32 XTP CrossPoint 1600 and 3200 • Remote Contr ol 33 XTP CrossPoint 1600 and 3200 • Remote Contr ol Command SIS Command (Host to Unit) Response (Unit to Host) Additional Description Information requests Information request I V X1( X X2) • A X1( X X2)] In the response: V X1( X X2) is the video matrix size. A X1( X X2) is the audio matrix size. ...

  • Extron electronic 1600 - page 21

    34 XTP CrossPoint 1600 and 3200 • Remote Contr ol 35 XTP CrossPoint 1600 and 3200 • Remote Contr ol NOTE : X! = Input number 01 – 16 or 32 X1& = Signal detection status 0 = no input connected 1 = input connected X* = HDCP status (for inputs) 0 = no source connected 1 = Source is HDCP-compliant 2 = Source is not HDCP compliant Command SIS ...

  • Extron electronic 1600 - page 22

    36 XTP CrossPoint 1600 and 3200 • Remote Contr ol 37 XTP CrossPoint 1600 and 3200 • Remote Contr ol NOTE : X@ = Output number 01 – 16 or 32 X1) = Mute 0 = off (unmuted) 1 = on (muted) X2% = Video and audio mute 0 = no mute 1 = video mute 2 = audio mute 3 = video and audio mute Command SIS Command (Host to Unit to Endpoint) Response (Endpoint ...

  • Extron electronic 1600 - page 23

    38 XTP CrossPoint 1600 and 3200 • Remote Contr ol 39 XTP CrossPoint 1600 and 3200 • Remote Contr ol Command SIS Command (Host to Unit to Endpoint) Response (Endpoint to Unit to Host) Additional Description Input video format (available for endpoint input 1 only) Set format X! * Y# Ityp X! * Y# * Y$] Set input 1 on endpoint X! to Y# video form ...

  • Extron electronic 1600 - page 24

    40 XTP CrossPoint 1600 and 3200 • Remote Contr ol 41 XTP CrossPoint 1600 and 3200 • Remote Contr ol Command SIS Command (Host to Unit to Endpoint) Response (Endpoint to Unit to Host) Additional Description Input audio selection NOTE : These commands select between the audio embedded in the digital video stream and the 2-channel analog audio. In ...

  • Extron electronic 1600 - page 25

    42 XTP CrossPoint 1600 and 3200 • Remote Contr ol 43 XTP CrossPoint 1600 and 3200 • Remote Contr ol XTP System Configuration Program Another way to operate the switcher is via the Windows ® -based XTP System Conguration software. For details on installing and operating the program, see the XTP System Configuration Software Guide . Accessin ...

  • Extron electronic 1600 - page 26

    XTP CrossPoint 1600 and 3200 • Configuration 45 44 XTP CrossPoint 1600 and 3200 • Remote Contr ol Configuration Removing and Installing a Board or Blank Panel NOTES: • For proper cooling and air ow , boards or blank panels should be installed in all locations during normal switcher operations. • The input and output boards ar e hot-swa ...

  • Extron electronic 1600 - page 27

    46 XTP CrossPoint 1600 and 3200 • Configuration Align with Plastic Guide s IN XTP CP 4i HDMI AUDIO L R L R L R L R IN Knurled Knobs ...

  • Extron electronic 1600 - page 28

    Extron W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years fr om the date of purchase. In the event of malfunction du ri ng the warranty period attributable directly to faulty workmanship and/or materials, Ext ron Electronics will, at its option, r epair or replace said produc ...

  • Extron electronic 1600 - page 29

    Extron USA Headquarters +800.633.9876 (Inside USA/Canada Only) Extron USA - W est Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 F AX +1.919.850.1001 F AX Extron Europe +800.3987.6673 (Inside Europe Only) +31.33.453.4040 +31.33.453.4050 F AX Extron India 1800.3070.3777 (Inside India Only) +91-80 3055.3777 +91 80 3055 3737 F AX Ex ...

Manufacturer Extron electronic Category Switch

Documents that we receive from a manufacturer of a Extron electronic 1600 can be divided into several groups. They are, among others:
- Extron electronic technical drawings
- 1600 manuals
- Extron electronic product data sheets
- information booklets
- or energy labels Extron electronic 1600
All of them are important, but the most important information from the point of view of use of the device are in the user manual Extron electronic 1600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Extron electronic 1600, service manual, brief instructions and user manuals Extron electronic 1600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Extron electronic 1600.

Similar manuals

A complete manual for the device Extron electronic 1600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Extron electronic 1600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Extron electronic 1600.

A complete Extron electronic manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Extron electronic 1600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Extron electronic 1600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Extron electronic 1600, that we can find in the current document
3. Tips how to use the basic functions of the device Extron electronic 1600 - which should help us in our first steps of using Extron electronic 1600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Extron electronic 1600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Extron electronic 1600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Extron electronic 1600?

Use the form below

If you did not solve your problem by using a manual Extron electronic 1600, ask a question using the form below. If a user had a similar problem with Extron electronic 1600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)