English dropdown-ico

Manual Summit E-321

11 pages 6.38 mb
Download

Go to site of 11

Summary
  • Summit E-321 - page 1

    Disassembly Instructions Lexmark E-321/E323 Toner Cartridge First released in April, 2003, the Lexmark E321/323 series of printers are based on a 20ppm 1200 dpi Lexmark engine. Lexmark is using the Prebate cartridges again, and these cartridges also use a non-resetable chip to prevent the Prebate car - tridges from being recycled. The Non-Prebate c ...

  • Summit E-321 - page 2

    DOC-0331 Page 2 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) These cartridges come new with a shipping lock/foam combination. The shipping lock and foam are unique to the E320/321 series of cartridges. See Figure 1 Required Tools Toner approved vacuum. 2) A small Common screw driver 3) A spring hook 4) Needle nose pliers Requ ...

  • Summit E-321 - page 3

    DOC-0331 Page 3 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 2 Figure 3 Figure 4 Figure 5 1) On the left side of the cartridge (Chip Side) remove the 3 screws. See Figure 2 2) Carefully remove the end cap. Note that a spring will come loose and the cartridge will basically fall apart at this point. If you intend to re- ...

  • Summit E-321 - page 4

    DOC-0331 Page 4 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 6 Figure 7 Figure 8 Figure 9 5) Remove the two front screws only from the right end cap. The back screw holds the long brace in place and does not need to be removed. See Figure 7 6) Remove the drum coupling gear (Smaller version of the 4039/4049). Remove the ...

  • Summit E-321 - page 5

    DOC-0331 Page 5 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 10 Figure 11 Figure 12 Figure 13 7) Remove the two screws on the wiper blade, and the blade. Clean out the waste chamber. The screws for the wiper blade are smaller than the end cap screws. See Figure 10 NOTE: Be very careful not to damage or distort the thin ...

  • Summit E-321 - page 6

    DOC-0331 Page 6 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 14 Figure 15 Figure 16 Figure 17 11) On the left side of the toner hopper (fill plug side), pry out the developer roller bushing. See Figure 14 12) Remove the developer roller. Be careful not to damage the black retaining blade. See Figure 15 13) Clean the wo ...

  • Summit E-321 - page 7

    DOC-0331 Page 7 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 18 Figure 19 Figure 20 Figure 21 15) Fill the hopper with 225g of E320 toner. Replace the fill plug. See Figure 18 16) Install the doctor blade spring holder, spring and screw. See Figure 19 17) Install the waste chamber into the right end cap. Install the 2 ...

  • Summit E-321 - page 8

    DOC-0331 Page 8 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 22 Figure 23 Figure 24 Figure 25 19) Install the spring large loop side on the large toner hopper post. See Figure 22 20) Install the coupler gear on to the shaft on the toner supply. Note that the gear and shaft are both keyed. See Figure 23 21) Install the ...

  • Summit E-321 - page 9

    DOC-0331 Page 9 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 26 23) If you have a Prebate cartridge, install the replacement chip in the left end cap. Make sure that the chip is locked in place by the two plastic tabs. See Figure’s 26 & 27 Figure 27 Figure 28 Figure 29 24) Clean off all the old conductive grease ...

  • Summit E-321 - page 10

    DOC-0331 Page 10 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 30 Figure 31 26) Carefully align and install the left end cap. Make sure the back brace fits correctly and that the alignment pins are all in there correct position. Snap the end cap in place. See Figure’s 30 & 31 Figure 32 Figure 33 27) With the sprin ...

  • Summit E-321 - page 11

    DOC-0331 Page 11 www.summitlaser.com Lexmark E-321/E323 Toner Cartridges (Continued) Figure 34 Figure 35 29) With the springs in the correct position, bend the drum cover slightly in the middle. Place the alignment pins in their respective slots. Try to make sure the large tail of the spring fits in place as you fit the cover in place. See Figure? ...

Manufacturer Summit Category Printer Accessories

Documents that we receive from a manufacturer of a Summit E-321 can be divided into several groups. They are, among others:
- Summit technical drawings
- E-321 manuals
- Summit product data sheets
- information booklets
- or energy labels Summit E-321
All of them are important, but the most important information from the point of view of use of the device are in the user manual Summit E-321.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Summit E-321, service manual, brief instructions and user manuals Summit E-321. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Summit E-321.

Similar manuals

A complete manual for the device Summit E-321, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Summit E-321 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Summit E-321.

A complete Summit manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Summit E-321 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Summit E-321, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Summit E-321, that we can find in the current document
3. Tips how to use the basic functions of the device Summit E-321 - which should help us in our first steps of using Summit E-321
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Summit E-321
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Summit E-321 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Summit E-321?

Use the form below

If you did not solve your problem by using a manual Summit E-321, ask a question using the form below. If a user had a similar problem with Summit E-321 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)