-
Scytek electronic 8000 - page 1
V I S I O N G U A R D 8000 VEHICLE SECURITY SYSTEM WITH BUILT-IN CAMERA AND REMOTE START PRODUCT MANUAL ...
-
Scytek electronic 8000 - page 2
L i m i t e d L i f e t i m e W a r r a n t y This vehicle security system is warranted to the original purchaser , to be free from defects in material and workmanship. The manufacturer will rep air or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal i ...
-
Scytek electronic 8000 - page 3
1. About Y our System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 2. Remote T ransmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .P age 2 Remote T ransmitter Description . . . . . . . . . . . . . . . . . . . . . ...
-
Scytek electronic 8000 - page 4
...
-
Scytek electronic 8000 - page 5
The ScyT ek Vision Guard 8000 is a combination vehicle security and remote starting system f eaturing a built-in "ScyNet Network P ort" that allows direct connection of optional accessory modules and a PC interface off ering expanded system operation. With proper installation this system will provide superior protection and performance fo ...
-
Scytek electronic 8000 - page 6
Standard Remote Transmitter Description The VisionGuard 8000 is compatible with the optional 5-button R emote T ransmitters used to control system operations. Note : Using the optional PC or P ocket PC interface with the network softw are, it is possible to reconfigure the functionality of the tr ansmitter buttons. The standard (default) setting f ...
-
Scytek electronic 8000 - page 7
Adding/Replacing Transmitters T o replace lost or stolen transmit ters or to add additional transmitters into the system, ha ve all desired transmit ters ready and follow the steps below . Note : Up to 4 one-wa y transmitters can be progr ammed to operate the system. An y previously stored transmit ter codes will be erased if not progr amed within ...
-
Scytek electronic 8000 - page 8
Page 4 - VisionGuard 8000 True Color 2-way Camera Ready Remote Transmitter Description The VisionGuard 8000 True Color 2-way LCD remote transmitter, is offering increased range and confirmation of any activated features. Button 1 Arms the system. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms the system. Button 2 a ...
-
Scytek electronic 8000 - page 9
VisionGuard 8000 - Page 5 5. The siren will chirp 3 times to indicate system has exited programming mode. System Confirmation The 2-wa y transmitter's confirmation f eature allows the current vehicle status to be displayed at any time. T o display system status: Press and hold Button 4 until the display shows CON. · The transmit ter will beep ...
-
Scytek electronic 8000 - page 10
Page 6 - VisionGaurd 8000 Programable Functions using the LCD Transmitter Pressing and holding transmitter button 4 will scroll through several transmitter programable options. CHIRP T o set the siren’ s confirmation chirps ON or OFF : 1.Press and hold button 4 until the icon “chirp” appears. · The transmit ter will beep twice. 2.Release but ...
-
Scytek electronic 8000 - page 11
VisionGaurd 8000 - Page 7 C a m e r a F e a t u r e s ...
-
Scytek electronic 8000 - page 12
VisionGuard 8000 - Page 8 ...
-
Scytek electronic 8000 - page 13
VISIONGAURD 8000 - Page 9 Remote Arming The system monitors 5 independent areas ( zones ) while armed: doors, hood/ trunk, shock sensor , optional sensor input, and the network port for future expansion. T o Arm the System: 1. T urn off the ignition. 2. Press and release Button 1. · The siren will chirp once.* · The doors will lock. · The parkin ...
-
Scytek electronic 8000 - page 14
Page 10- VisionGaurd 8000 Tamper Alert If the system was triggered while awa y , the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times. LED Flashes (60 seconds): 1 flash = optional sensor 2 flashes = shock sensor 3 flashes = network based sensor 4 flashes = ...
-
Scytek electronic 8000 - page 15
VisionGaurd 8000 - Page 11 Panic Mode In the event of an emergency the tr ansmitter’s remote P anic feature can be used to instantly trigger the alarm. T o activate the P anic Mode: 1. Press and hold Button 1 for 3 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Pres ...
-
Scytek electronic 8000 - page 16
Page 12- VisionGaurd 8000 T o set the Emergency Override Code: 1. T urn on ignition. 2. Within 5 seconds, press the v alet switch 5 times. · The siren will provide one long chirp, indicating that y ou have entered Progr amming. 3. Press the v alet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, p ...
-
Scytek electronic 8000 - page 17
VisionGaurd 8000 - Page 13 Remote Starting T o Remote Start the S ystem: 1. Be sure the system is not in V alet Mode. 2. Press and hold Button 4 on one wa y remote or button 3 on LCD remote for three seconds. · The parking lights will flash 4 times and turn on. · The Siren will chirp 4 times. · The engine will start and run for the dur ation of ...
-
Scytek electronic 8000 - page 18
Page 14- VisionGaurd 8000 Turbo Timer Feature The T urbo Timer feature allows vehicles with turbocharged engines to remain running after the ignition key is removed, f or proper cool-down of the turbocharger . The T urbo Timer feature requires connection to the vehicle’ s parking brake wire. T o activate the T urbo Timer feature: 1. Leave the eng ...
-
Scytek electronic 8000 - page 19
VisionGaurd 8000 - Page 15 E x t e n d e d F e a t u r e s Ignition Door Locking F or added safety , the Ignition Door Locking feature allows v ehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled ...
-
Scytek electronic 8000 - page 20
Page 16 VisionGaurd 8000 1. Thoroughly read and become familiar with the installation instructions bef ore beginning the installation. 2. R eview system contents: Main Unit One 5-Button one-w ay Remote T ransmitter One 4 Button two-w ay Remote T ransmitter Siren Shock Sensor Harnesses • 6-Pin starter harness • 20-Pin main harness • 4-Pin shoc ...
-
Scytek electronic 8000 - page 21
VisionGaurd 8000 - Page 17 Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief , and will not interfere with the oper ation of any vehicle components such as f oot pedals, steerin ...
-
Scytek electronic 8000 - page 22
Page 18- VisionGaurd S y s t e m W i r i n g 6-Pin Starter Harness Pin 1 RED WIRE A : Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply . R emo v e the fuse until the installation is complete and all wiring is check ed. Pin 2 RED WIRE B : Main Power Input B (+). Connect to the ...
-
Scytek electronic 8000 - page 23
VisionGaurd 8000- Page 19 when the door is open. This type of door circuit is usually found on F ord vehicles. Pin 12 GREEN WIRE : Negativ e Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHITE/BLACK WIRE : Hood Pin Input (-). Connect the to the hood pin switch. The switch must provide a grou ...
-
Scytek electronic 8000 - page 24
Page-20 VisionGaurd 8000 Jumper Selection Carefully separ ate the top and bottom halves of the main unit case. Once the cov er is removed, the parking light polarity jumper will be visible next to the parking light relay . Set the jumper for the correct polarit y output as described below , then reassemble the main unit case. Parking Light Output. ...
-
Scytek electronic 8000 - page 25
VisionGaurd 8000 - Page 21 Entering System Programming This system is compatible with both the optional LCD tr ansmitter or the standard FM transmit ter , all system programming can be perf ormed using either one. T o enter System Progr amming: 1. T urn on ignition. 2. Within 5 seconds, press the v alet switch 5 times. · The siren will provide thr ...
-
Scytek electronic 8000 - page 26
Page- 22 VisionGaurd 5. Ignition Door Unlocking. Selects whether or not the system automatically unlocks the doors when the ignition is turned off . The Ignition Door Locking f eature may be programmed to unlock all doors or the driver’ s door only . If driver ’ s door only is selected, the optional Passenger Unlock wire must be connected. ( Se ...
-
Scytek electronic 8000 - page 27
VisionGaurd 8000 - Page 23 8. Passive Door Locking. Selects whether or not the system will automatically lock the doors during P assive Arming and Auto Rearming mode. 9. Passive Arming Entry Delay. When selected, the siren will chirp for 10 seconds before sounding if a door is opened. The system may be disarmed by simply turning on the ignition whe ...
-
Scytek electronic 8000 - page 28
Page-24 VisionGaurd 8000 Diesel Engine. Sets the engine type f or Diesel and monitors the glow plug input to make sure the glow plugs are warm before cr anking the starter . If the glow plug wire is not connected, the built-in timer waits 15 seconds before automatically cr anking the starter . 22. Ignition 2 Relay Program. Selects one of three oper ...
-
Scytek electronic 8000 - page 29
VisionGaurd 8000 - Page 25 W i r i n g D i a g r a m s TO POSITIVE DOME LIGHT +12V Black/White (-) DOME LIGHT OUTPUT TO NEGATIVE DOME LIGHT +12V Black/White (-) DOME LIGHT OUTPUT P ositive Dome Light Negative Dome Light TO POSITIVE HORN WIRE +12V Brown/White (-) HORN OUTPUT TO NEGATIVE HORN WIRE +12V Brown/White (-) HORN OUTPUT P ositive Horn Honk ...
-
Scytek electronic 8000 - page 30
Page-26 VisionGaurd 8000 Negative T rigger Positive T rigger (using inverter or relays) R everse P olarity V acuum Adding Actuators F ollow the diagrams below for connecting basic door lock systems. F or T wo Stage door lock systems (separately unlocks driv er and passenger doors) see following pages. D o o r L o c k D i a g r a m s ...
-
Scytek electronic 8000 - page 31
VisionGaurd 8000 - Page 27 T w o S t a g e D o o r L o c k D i a g r a m s T wo Stage Negative T rigger T wo Stage P ositive T rigger The VisionGuard 8000 is equipped with a dedicated P assenger Unlock output allowing T wo Stage Door Lock operation. When connected as shown below , disarming the system will unlock only the driver’ s door . Pressin ...
-
Scytek electronic 8000 - page 32
Page-28 VisionGaurd 8000 T w o S t a g e D o o r L o c k Diagrams c o n t ’ d T wo Stage R everse P olarity T wo Stage Adding Actuators ...
-
Scytek electronic 8000 - page 33
VisionGaurd 8000 - Page 29 FCC ID: OARRXAM2000 This device complies with P art 15 of FCC Rules. Operation is subject to the f ollowing two conditions: 1) This device may not cause harmf ul interference. 2) This device must accept any interf erence received, including interference that may cause undesired operation T e c h n i c a l I n f o r m a t ...
-
Scytek electronic 8000 - page 34
Page-30 VisionGaurd 8000 S t a r t e r D i a g n o s t i c s Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected Hood T rigger is active 4 Times - Brak e T rigger is active 5 Times - Unit is in V alet (service) mode, and start is disabled. ...
-
Scytek electronic 8000 - page 35
VisionGaurd 8000 - Page 31 ...
-
Scytek electronic 8000 - page 36
ScyTek Electronics 11627 Cantara Street North Hollywood, CA 91605 © ScyT ek Electronics 2006 VisionGuard 8000 r1 4/06 W i r i n g D i a g r a m ScyNet Blue Star t (-) Green Emer gency brak e(-) Antenna with built -in Camera Shock Sensor LED V alet Switch Green Lock output (-) 500mA Red +12V relay power output 100mA Blue Unlock output (-) 500mA Gre ...
Do you have a question concerning Scytek electronic 8000?
Use the form below
If you did not solve your problem by using a manual Scytek electronic 8000, ask a question using the form below. If a user had a similar problem with Scytek electronic 8000 it is likely that he will want to share the way to solve it.