English dropdown-ico

Manual Dynalink ALE800

30 pages 0.64 mb
Download

Go to site of 30

Summary
  • Dynalink ALE800 - page 1

    User Manual ALE800 Home DSL Modem ...

  • Dynalink ALE800 - page 2

    able of Contents I. About This Manual 2 II. Preface 3 III. Overview 4 About ADSL 4 Protocol and Device Driver Selection 4 Features 8 Description of the Front Panel LEDs 9 Description of the Rear Panel Connectors 9 IV. USB ADSL Modem Hardware Installation 10 V. Software Installation 11 Before You Start 11 Windows Installation 13 Installing the Drive ...

  • Dynalink ALE800 - page 3

    2 This manual provides a comprehensive user’s guide and installation manual for USB ADSL modem. It has been organized in a way that should make it easy to follow by users worldwide. In order to ensure optimal comprehension, the following list provides brief descriptions of the formatting styles used in this manual.  Commands: Commands are alwa ...

  • Dynalink ALE800 - page 4

    3 This manual contains information regarding the installation, operation, and configuration of the USB ADSL Modem. Additionally, it outlines the use of the Control Panel Application. The following chapters are included in this manual:  Overview: It offers a brief description of ADSL, protocol and device driver selection, and the features of the ...

  • Dynalink ALE800 - page 5

    4 About ADSL Asymmetric Digital Subscriber Line (ADSL) technology provides high-speed data access across regular phone lines (copper wires) by making use of previously unused frequency bandwidth above the voice band. By placing the ADSL signal above the frequency of the voice signal, ADSL service is able to coexist on the same line with your teleph ...

  • Dynalink ALE800 - page 6

    5 Several different protocols are used on top of ATM. The protocol required in your configuration depends on the equipment deployed by your DSL service provider. There are several possibilities: 1. Point to Point Protocol (PPP) Over ATM (RFC 2364) PPP provides session setup, user authentication (login), and encapsulation for upper layer protocols s ...

  • Dynalink ALE800 - page 7

    6 1. WAN driver This driver causes the modem to resemble a dial-up modem. Call establishment is performed through Dial-Up Networking. This driver supports RFC 2364 and 2516 with PVC connections. It can be used with Windows 98, Windows 98 SE, Windows 2000, Windows Me, and Windows XP. 2. LAN driver This driver makes the modem appear as a LAN or Ether ...

  • Dynalink ALE800 - page 8

    7 The device driver choices are summarized in the table below: Driver Type Protocol Operating System WAN RFC 2364 RFC 2516 (not with MAC OS 9.x, nor with MAC OS X) Windows 2000 Windows XP Windows Me Windows 98 SE Windows 98 LAN RFC 1483 RFC 2516 (MAC OS X 10.1.x and above, only) Windows 2000 Windows XP Windows Me Windows 98 SE Windows 98 ATM RFC 15 ...

  • Dynalink ALE800 - page 9

    8 Features The USB ADSL Modem provides the following features:  Compliant with Universal Serial Bus Specification Revision 1.1  USB bus-powered; an external power supply is not required  Supports three device drivers: Microsoft NDIS 4.0 WAN Miniport, NDIS 4.0 LAN Miniport or NDIS 5.0 ATM Miniport  Compatible with T1.413 i2, G.DMT, and G ...

  • Dynalink ALE800 - page 10

    9 Description of the front Panel LEDs LED LABEL Power (PW) LINK (LK) Color Status Green Green Green steady Power On Link Green blink N/A No Connection OFF Power Off N/A Table 1-1 Front Panel LEDs Description of the Rear Panel Connectors BACK PANEL CONNECTOR DESCRIPTION Line ADSL Port Phone RJ-11 phone connector (optional) USB USB Port Table 1-2 Bac ...

  • Dynalink ALE800 - page 11

    10 Hardware Installation Install the USB ADSL Modem by following these steps with the PC running: 1. Insert the rectangular end of a USB cable into the USB port of your PC. 2. Insert the square end of the USB cable into the USB port of the USB ADSL Modem. Note: The USB cable should not be inserted until you are prompted by software installation to ...

  • Dynalink ALE800 - page 12

    11 The software installation procedures vary depending upon the operating system of your PC. Be sure to follow the instructions provided for the operating system appropriate for you. Before you start… The following information may be required for software installation. Contact your DSL service provider before proceeding with software installation ...

  • Dynalink ALE800 - page 13

    12  ATM Virtual Path ID (VPI) Note: Required if not using default value  ATM Virtual Circuit ID (VCI) Note: Required if not using default value  Encapsulation type Note: Required if not using default value  Modulation type Note: Required if not using default value  User Name (for PPP applications only)  Password (for PPP applicati ...

  • Dynalink ALE800 - page 14

    Windows Installation The software setup process for Microsoft Windows applications (XP, 2000, Me, 98 SE, and 98) is described below with operating system specific differences noted. The USB ADSL Modem should be connected to your PC prior to installing the driver software. No other Windows programs should be running on your PC during the software in ...

  • Dynalink ALE800 - page 15

    14 3. A Licensing Agreement message will be displayed; click Accept. 4. The Select Service Provider window allows you to specify your DSL service provider. A list of service providers is displayed. Default values for the Type of Driver, ATM Virtual Path ID (VPI), ATM Virtual Circuit ID (VCI), Encapsulation type and Modulation type are provided for ...

  • Dynalink ALE800 - page 16

    15 a) Select the type of driver to be installed from the Select Driver Type window and click Next. b) Enter/Select the VPI, VCI, Encapsulation type and Modulation type from the Communication Settings window and click Next. Note: The encapsulation types that appear in the drop-down list vary depending upon the type of driver selected in the previous ...

  • Dynalink ALE800 - page 17

    16 5. The Ready to Install window will be displayed. You may review the current settings and click Back to change the settings, or click Next to accept the current settings. 6. A message will be displayed indicating that the drivers are being installed. Note: You may need the Windows CD to complete the installation. ...

  • Dynalink ALE800 - page 18

    17 7. The Installing window will be displayed. You may insert USB cable now. 8. The system must be rebooted to have the new settings take effect, therefore the Reboot window will appear. Remove all disks from their drives, select Yes, reboot the computer now; and click Close to reboot. ...

  • Dynalink ALE800 - page 19

    18 9. Once the PC has rebooted, installation of the USB Modem is complete. The Finished window will be displayed indicating the installation has been completed. Click Finish. ...

  • Dynalink ALE800 - page 20

    19 Accessing Communication Settings on Windows Once the USB ADSL Modem and software have been installed, the communication settings may be easily updated by performing the following steps: 1. From your PC desktop click Start  Programs  DSL Modem  Configure. 2. The Communication Settings window will be displayed. Make the necessary changes ...

  • Dynalink ALE800 - page 21

    20 Windows Drivers Update Once the USB ADSL Modem has been installed, updating to a new version of the software is an easy process. Simply uninstall the existing drivers, and then install the new drivers. Note: Be sure to follow the instructions provided for the appropriate operating system for your application. Updating the USB ADSL Modem Software ...

  • Dynalink ALE800 - page 22

    21 The DSL Modem Status provides a quick and easy way to configure and check the performance of the modem and the ADSL connection. When open, the monitor window updates every 2 seconds. DSL Modem Status 1. There are two methods to access the control panel:  From your PC desktop, click Start  Programs  DSL Modem  DSL or  From the PC d ...

  • Dynalink ALE800 - page 23

    22 3. Driver Version and Control Panel Version would be listed after clicking button. ...

  • Dynalink ALE800 - page 24

    23 Windows Uninstall Remove the USB ADSL Modem software drivers by performing the following steps. 1. From your PC desktop click Start  Programs  DSL Modem  Uninstall. 2. A message will be displayed asking you to confirm the removal of the USB ADSL modem software, click Yes. 3. A message will be displayed to remind you don’t unplug the U ...

  • Dynalink ALE800 - page 25

    24 5. A message will be displayed to remind you to unplug your modem. You may unplug the USB cable now. 6. The Reboot window will appear. Remove all disks from their drives, select Yes, reboot the computer now; and click Close to reboot. Note: The USB cable must be unplugged before the system is rebooted. ...

  • Dynalink ALE800 - page 26

    25 Point-to-Point Protocol over Ethernet PPPoE (Point-to-Point Protocol over Ethernet) is a specification for connecting multiple computer users on an Ethernet to a remote site through common customer premises equipment. PPPoE can be used to have an office or building- full of users share a common DSL (Digital Subscriber Line) connection to the Int ...

  • Dynalink ALE800 - page 27

    26 PPPoE for LAN Applications PPPoE is supported via third party software when implemented with a LAN driver, making the modem appear as a local area network (LAN) device to the operating system. It allows multiple computer users on an Ethernet to share a common DSL connection to the Internet. After installing the LAN driver, follow the installatio ...

  • Dynalink ALE800 - page 28

    27 USB ADSL Modem Connector The USB ADSL Modem is connected to your PC via a USB cable. The rectangular end of the USB cable inserts into the USB port of your PC while the square end of the cable inserts into the USB port of the USB ADSL Modem. An RJ-11 connector is provided for connection to the telephone line. Data Transfer Rates ANSI T1.413 / IT ...

  • Dynalink ALE800 - page 29

    28 ITU G.992.2 Data Rates Data rates for G.992.2 (G.lite) mode are likewise partitioned at 32kb/s increments. The downstream data rates extend from 64 kb/s to 4 Mb/s. The upstream data rates extend from 32 kb/s to 1024 kb/s. Bit Rate (kb/s) Min Max Downstream 64 4000 Upstream 32 1024 Table 2: G.992.2 Payload Bit Rates Power Requirements Typical Pow ...

  • Dynalink ALE800 - page 30

    29 System Requirements Windows Operating Systems Windows 98, Windows 98SE, Windows ME, Windows 2000, or Windows XP 32 MB RAM Pentium-class processor (200MHz or better) 1 Universal Serial Bus (USB) port 10 MB free HD space Hardware Requirements Processor Intel-compatible 80486 or higher, including Pentium and Pentium Pro. ...

Manufacturer Dynalink Category Modem

Documents that we receive from a manufacturer of a Dynalink ALE800 can be divided into several groups. They are, among others:
- Dynalink technical drawings
- ALE800 manuals
- Dynalink product data sheets
- information booklets
- or energy labels Dynalink ALE800
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dynalink ALE800.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dynalink ALE800, service manual, brief instructions and user manuals Dynalink ALE800. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dynalink ALE800.

Similar manuals

A complete manual for the device Dynalink ALE800, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dynalink ALE800 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dynalink ALE800.

A complete Dynalink manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dynalink ALE800 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dynalink ALE800, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dynalink ALE800, that we can find in the current document
3. Tips how to use the basic functions of the device Dynalink ALE800 - which should help us in our first steps of using Dynalink ALE800
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dynalink ALE800
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dynalink ALE800 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dynalink ALE800?

Use the form below

If you did not solve your problem by using a manual Dynalink ALE800, ask a question using the form below. If a user had a similar problem with Dynalink ALE800 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)