English dropdown-ico

Manual Audiovox APS 675

18 pages 0.41 mb
Download

Go to site of 18

Summary
  • Audiovox APS 675 - page 1

    Model APS 675 Installation Manual 3 Channel Remote Start / Keyless Entry System Installation Instructions This Unit Is Intended For Installation In V ehicles With 12 V olt Negative Ground Electrical Systems, Gasoline or Diesel With T rue T ach Reference And Automatic T ransmissions Only . Kit Contents APS-675 Control Module (2) - 3 Button Anti Code ...

  • Audiovox APS 675 - page 2

    The APS-675 Remote Start/Keyless Entry System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesel engine has a instant fire, (no glow plug p ...

  • Audiovox APS 675 - page 3

    3 allowed for the body of the switch, and also that the drill will not penetrate any existing factory wiring or fluid lines. Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside. Secure the switch using the nut, star washer , and on/off face plate. It is suggested that the switch be ...

  • Audiovox APS 675 - page 4

    used ) and the neutral safety switch as shown in the following diagram. Failure to connect this wire to the ignition switch side of the of the neutral safety switch can result in personal injury and property damage. SEE NEUTRAL ST ART SAFETY TEST FOR FUR THER DET AILS. BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the i ...

  • Audiovox APS 675 - page 5

    WIRING CONNECTIONS: 12 Pin Input / Output Harness Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. BLACK w/WHITE Tracer Wire: Control Switch The Black w/ Wh ...

  • Audiovox APS 675 - page 6

    Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: YOU MUST DISCONNECT THE IGNITION INPUT OF THE ALARM FROM ANY OTHER WIRE THAT IT IS PRESENTLY CONNECTED TO IN THE VEHICLE. This wire provide sa+1 2 Volt output when the ignition key is turned to the “ON” position, and 0 Volts when the igniti ...

  • Audiovox APS 675 - page 7

    The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activation period, then vibration from the running vehicle can cause the alarm to trigger . In this case, connect the Light Blue Wire to terminal #86 of a ...

  • Audiovox APS 675 - page 8

    DARK GREEN/ORANGE Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil. This Remote Start unit learns th ...

  • Audiovox APS 675 - page 9

    3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness provide sa+1 2 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay . The Green wire of the two pin harne ...

  • Audiovox APS 675 - page 10

    T ypically this output will be used to re-lock the vehicle doors if the doors unlock automatically when the ignition circuit transitions to off. Black w/ Y ellow T race Wire: Ground Output During S tart (Crank) The Black w/ Y ellow Trace wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This outpu ...

  • Audiovox APS 675 - page 11

    Dark Blue/Black and Green/White - 2 Pin Input/Output Harness: Dark Blue/Black T race Wire: External T rigger Input The Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. The intent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK" paging system or similar device. When ...

  • Audiovox APS 675 - page 12

    To program these selectable features: 1. Start with the programming switch in the OFF position. 2. Turn the ignition key to the ON position. 3. Flip the program switch ON - OFF - ON - OFF - ON - then OFF. 4. Immediately turn the ignition key OFF, then back to ON. 5. Flip the program switch ON - OFF - ON - then OFF. 6 . Use button 1 on the transmitt ...

  • Audiovox APS 675 - page 13

    TIMED ST ART PROGRAM: The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is useful in extremely cold climates where starting the engine is the only means to keep the battery charged and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48 hours. ...

  • Audiovox APS 675 - page 14

    T o test the integrity of this circuit: 1. With the driver's window in the down position, start the vehicle using the RF transmitter . 2. Reach inside the car and pull the hood release. 3. Raise the hood and confirm that the remote start unit shuts down. If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of ...

  • Audiovox APS 675 - page 15

    MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERA TIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or neutral, the mechanical function will n ...

  • Audiovox APS 675 - page 16

    Additional information concerning Key In Sensor method s1&2a r e listed below and should be reviewed before considering either alternative. Method 1 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than Park or Neutral while the key is in the ignition cylinder however , if th ...

  • Audiovox APS 675 - page 17

    METHOD 2 T o connect to the key in sensor circuit as shown for method 2: A . Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B . Cut this wire and connect the ignition cylinder side to chassis ground. C . Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. ...

  • Audiovox APS 675 - page 18

    WIRING DIAGRAM 18 2nd White © 1998 Audiovox Corp., Hauppauge, N.Y . 1 1788 Form No. 128-5367 ...

Manufacturer Audiovox Category Automobile Electronics

Documents that we receive from a manufacturer of a Audiovox APS 675 can be divided into several groups. They are, among others:
- Audiovox technical drawings
- APS 675 manuals
- Audiovox product data sheets
- information booklets
- or energy labels Audiovox APS 675
All of them are important, but the most important information from the point of view of use of the device are in the user manual Audiovox APS 675.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Audiovox APS 675, service manual, brief instructions and user manuals Audiovox APS 675. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Audiovox APS 675.

Similar manuals

A complete manual for the device Audiovox APS 675, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Audiovox APS 675 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Audiovox APS 675.

A complete Audiovox manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Audiovox APS 675 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Audiovox APS 675, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Audiovox APS 675, that we can find in the current document
3. Tips how to use the basic functions of the device Audiovox APS 675 - which should help us in our first steps of using Audiovox APS 675
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Audiovox APS 675
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Audiovox APS 675 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Audiovox APS 675?

Use the form below

If you did not solve your problem by using a manual Audiovox APS 675, ask a question using the form below. If a user had a similar problem with Audiovox APS 675 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (1)

Jose Gonzalez Voces

no puedo conectar el portátil al tp-link AV600 sin cable para conseguir mas potencia de wi-fi