English dropdown-ico

Manual Pentair 4/160

40 pages 3.4 mb
Download

Go to site of 40

Summary
  • Pentair 4/160 - page 1

    IntelliFlo ® 4/160 and 4/100 V ar iab le Speed Progr ammab le Pump (Compatib le with IntelliT ouch ™ , EasyT ouch ™ and IntelliComm) Installation and User’ s Guide IMPOR T ANT SAFETY INSTR UCTIONS READ AND FOLLO W ALL INSTR UCTIONS SA VE THESE INSTR UCTIONS A U T O HE A TE R SP A 100°F / 95°F AIR 70°F MON 09:30 AM ...

  • Pentair 4/160 - page 2

    © 2006 P entair W ater P ool and Spa, Inc. All rights reserved This document is subject to change without notice 1620 Hawkins A v e., Sanf ord, NC 27330 • (919) 566-8000 10951 W est Los Angeles A v e., Moorpar k, CA 93021 • (805) 553-5000 T rademarks and disclaimers : EasyT ouch, IntelliChlor , IntelliFlo , QuickT ouch and the P entair Water P ...

  • Pentair 4/160 - page 3

    i IntelliFlo 4 Installation and User ’ s Guide Important Safety Precautions ........................................................................................... ii Section 1: IntelliFlo Overview ........................................................................................... 1 IntelliFlo 4 V ar iable Speed Pump ................. ...

  • Pentair 4/160 - page 4

    ii IntelliFlo 4 Installation and User ’ s Guide Important Notice: Attention Installer: This manual contains important information about the installation, operation and safe use of this product. This information should be given to the o wner and/or operator of this equipment. W ARNING — Before installing this product, read and follow all warning ...

  • Pentair 4/160 - page 5

    iii IntelliFlo 4 Installation and User ’ s Guide IMPORTANT SAFETY PRECAUTIONS (continued) W ARNING — W ater temperature in excess of 100° F ahrenheit may be hazardous to y our health. Prolonged immersion in hot water ma y induce hyper ther mia. Hyper ther mia occurs when the inter nal temperature of the body reaches a level several degrees abo ...

  • Pentair 4/160 - page 6

    iv IntelliFlo 4 Installation and User ’ s Guide General Installation Information W ARNING — Pumps improperly sized or installed or used in applications other than for which the pump was intended can result in se vere personal injury or death. These r isks may include but not be limited to electric shock, fire, flooding, suction entrapment or se ...

  • Pentair 4/160 - page 7

    1 IntelliFlo 4 Installation and User ’ s Guide Section 1 Overview IntelliFlo 4 V ariable Speed Pump The IntelliFlo 4 variable speed pump is well suited for all of your pool, spa, cleaner , waterfall and other water application. Using the control panel, IntelliFlo can use one of the four selectable preset speeds or the pump speed can be adjusted t ...

  • Pentair 4/160 - page 8

    2 IntelliFlo 4 Installation and User ’ s Guide Features • Adjusts to various pool sizes • Prevents thermal overload • Detects and prevents damage from under and over voltage conditions • Protects against freezing • Communicates with a Pentair IntelliT ouch, EasyT ouch and IntelliComm system via a two-wire connection • Easy to use oper ...

  • Pentair 4/160 - page 9

    3 IntelliFlo 4 Installation and User ’ s Guide IntelliFlo 4 Drive Assembl y and Control P anel The IntelliFlo drive assembly consists of an operator control panel and the system electronics that drive the motor . The drive microprocessor controls the motor by changing the frequency of the current it receives together with changing the voltage to ...

  • Pentair 4/160 - page 10

    4 IntelliFlo 4 Installation and User ’ s Guide Controls and LEDs Speed 1, Speed 2, Speed 3, and Speed 4 button/LED: Press one of the speed buttons to select the desired preset pump speed. The pump preset speeds are: Speed 1 (750 RPM), Speed 2 (1500 RPM), Speed 3 (2350 RPM), and Speed 4 (31 10 RPM). The speed button LED is on when the selected but ...

  • Pentair 4/160 - page 11

    5 IntelliFlo 4 Installation and User ’ s Guide Section 2 Operating IntelliFlo 4 This section describes how to use the IntelliFlo 4 pump control panel. Setting the pump preset speed IntelliFlo 4 operates using one of the preset speeds. Use the speed buttons to select the preset speeds. T o set the pump speed 1. Ensure that the pump is powered on a ...

  • Pentair 4/160 - page 12

    6 IntelliFlo 4 Installation and User ’ s Guide Starting the pump T o start the pump 1. Ensure that the pump is powered on and the green power LED is on. 2. Press the S tart button (LED on) to start the pump. Note: When the pump is using a modified speed and is power ed down, the next time the pump is power ed up, the pump will use that same speed ...

  • Pentair 4/160 - page 13

    7 IntelliFlo 4 Installation and User ’ s Guide Priming the pump for the first time or after service Before the IntelliFlo 4 pump is started for the first time it must be primed. T o prime a pump means filling the pump and suction pipe with water . This process evacuates the air from all the suction lines and the pump. It may take several minutes ...

  • Pentair 4/160 - page 14

    8 IntelliFlo 4 Installation and User ’ s Guide Priming the pump for the first time or after service (Continued) Priming the Pump • Release all pressure from filter , pump, and piping system; see the filter owner ’ s manual. • In a flooded suction system (water source higher than pump), the IntelliFlo 4 pump will prime itself when suction an ...

  • Pentair 4/160 - page 15

    9 IntelliFlo 4 Installation and User ’ s Guide External Control with IntelliComm Communication Center The IntelliFlo 4 can be remotely controlled by the Pentair IntelliComm Communication Center using an optional communications cable (P/N 350122). The IntelliComm provides four pairs of input terminal connections. These inputs are actuated by eithe ...

  • Pentair 4/160 - page 16

    10 IntelliFlo 4 Installation and User ’ s Guide Connecting IntelliFlo 4 to an EasyT ouc h System The IntelliFlo 4 can be controlled by an EasyT ouch system via the RS-485 communication cable (P/N 350122). In this configuration, EasyT ouch starts, stops and controls the speed of the IntelliFlo pump. When the EasyT ouch does this, it rewrites the I ...

  • Pentair 4/160 - page 17

    11 IntelliFlo 4 Installation and User ’ s Guide 4. Lower down the hinged control panel to access the EasyT ouch motherboard. 5. Route the communication cable into the lower plastic grommet, up through the low voltage raceway to the EasyT ouch load center motherboard. 6. Strip back the cable conductors ¼ inch. Insert the two wires into the screw ...

  • Pentair 4/160 - page 18

    12 IntelliFlo 4 Installation and User ’ s Guide EasyT ouch Load Center (front view) Control panel access screw Control panel access screw High voltage cover panel Retaining screw 9. Close the control panel into its original position and secure it with the two access screws. 10. Install the high voltage cover panel and secure it with the two retai ...

  • Pentair 4/160 - page 19

    13 IntelliFlo 4 Installation and User ’ s Guide Connecting IntelliFlo 4 to an IntelliT ouch System The IntelliFlo 4 can be controlled by an IntelliT ouch system via the RS-485 communication cable (P/N 350122). In this configuration, IntelliT ouch 4 starts, stops and controls the speed of the IntelliFlo 4 pump. When the IntelliT ouch does this, it ...

  • Pentair 4/160 - page 20

    14 IntelliFlo 4 Installation and User ’ s Guide Connecting IntelliFlo to IntelliT ouch (Continued) 6. Strip back the cable conductors ¼”. Insert the wires into the either of the COM POR TS (J7 and J8) screw terminals located on the left side of the Personality board. Secure the wires with the screws. For wiring details, refer to the pin config ...

  • Pentair 4/160 - page 21

    15 IntelliFlo 4 Installation and User ’ s Guide Section 3 User Maintenance The following information describes how to service and maintain the IntelliFlo pump. Pump Strainer Basket The strainer , sometimes referred to as the “Hair and Lint Pot,” is in front of the of the pump. Inside there is a basket which must be kept clean of leaves and de ...

  • Pentair 4/160 - page 22

    16 IntelliFlo 4 Installation and User ’ s Guide Motor Service 1. Protect from heat: • Shade the motor and controller from the sun. • Any enclosure must be well ventilated to prevent overheating. Particular attention should be paid to the motor fan cover and the cooling fins between the drive and the motor. • Provide ample cross ventilation. ...

  • Pentair 4/160 - page 23

    17 IntelliFlo 4 Installation and User ’ s Guide Priming the pump after service Before a system start-up, the pump and system must be manually primed. Make sure to reopen valves before operating. T o prime IntelliFlo 4, the strainer pot must be filled with water . CA UTION — DO NO T run the pump dr y . If the pump is r un dr y , the mechanical s ...

  • Pentair 4/160 - page 24

    18 IntelliFlo 4 Installation and User ’ s Guide Blank P age ...

  • Pentair 4/160 - page 25

    19 IntelliFlo 4 Installation and User ’ s Guide Section 4 Installation and Remo v al The following information describes how to install the IntelliFlo 4 pump. Note: Before installing this product, read and follow all warning notices and instructions on page ii. IntelliFlo 4 Kit Contents • IntelliFlo 4 160 (or IntelliFlo 4 100) pump Installing t ...

  • Pentair 4/160 - page 26

    20 IntelliFlo 4 Installation and User ’ s Guide GROUND WIR E (GREEN) BONDING LUG Wiring the IntelliFlo 4 T o connect the IntelliFlo 4 to an AC power source: 1. Make sure all electrical breakers and switches are turned off before wiring motor. 2. Make sure that the wiring voltage is 230 VAC. 3. Use #12 AWG for wire runs up to 100 feet and #10 AWG ...

  • Pentair 4/160 - page 27

    21 IntelliFlo 4 Installation and User ’ s Guide Pump Disassembly W ARNING — Always disconnect power to the pool pump at the circuit breaker and disconnect the communication cab le bef ore ser vicing the pump. F ailure to do so could result in death or serious injury to serviceman, pool users or others due to electric shock. Read all servicing i ...

  • Pentair 4/160 - page 28

    22 IntelliFlo 4 Installation and User ’ s Guide Pump Disassembly (Continued) 9 . T o unscrew the impeller from the shaft, twist the impeller counterclockwise. 10. Remove the rotating portion of the mechanical seal from the impeller . 1 1. Remove the four bolts from the seal plate to the motor , using a 9/16 inch wrench. 12. Place the seal plate f ...

  • Pentair 4/160 - page 29

    23 IntelliFlo 4 Installation and User ’ s Guide Drive Assembly Removal and Installation T o remove the IntelliFlo 4 drive and control panel from the motor assembly: 1. Make sure all electrical breakers and switches are turned off before removing the drive. 2. Disconnect the RS-485 communication cable from the pump. 3. Open the control panel cover ...

  • Pentair 4/160 - page 30

    24 IntelliFlo 4 Installation and User ’ s Guide Replacement Parts Item Part Description No. No. 1 070387 BASKET AQ & WF 2 070429 B O L T HEX HD , 2-56x0.875 s/s, (QTY 4) 3 070430 B O L T 3/8 - 16 X 1¼ HEX CAP 18-8 s/s, (QTY 4) 4 070431 B O L T 3/8 -16 X 2 HEX CAP 18-8 s/s, (QTY 2) 5 070927 FOOT WF - PUMP MOTOR SUPPORT 6 070929 FOOT INSERT WF ...

  • Pentair 4/160 - page 31

    25 IntelliFlo 4 Installation and User ’ s Guide IntelliFlo Pump Dimensions 10.78 12.50 23.41 IntelliFlo 4 Electrical Specifications Circuit Protection: T wo-pole 20 AMP device at the Electrical Panel. Input: 230 V AC, 50/60 Hz, 3200 W atts Intelliflo Flow and P ower vs Flow Pump Curve ...

  • Pentair 4/160 - page 32

    26 IntelliFlo 4 Installation and User ’ s Guide Blank P age ...

  • Pentair 4/160 - page 33

    27 IntelliFlo 4 Installation and User ’ s Guide W arning and Alarm conditions The IntelliFlo 4 alarms and warnings are indicated by flashing LEDs on the control panel. For example, if a “Drive T emperature” warning occurs, the LED will blink two times, then Of f, then blink two times. This sequence is repeated until the condition is cleared. ...

  • Pentair 4/160 - page 34

    28 IntelliFlo 4 Installation and User ’ s Guide General IntelliFlo 4 T roubleshooting Pr oblems Use the following general troubleshooting information to resolve possible problems with your IntelliFlo 4 pump. Note: Switch the main power off to the pump before attempting service or repair . m e l b o r Pe s u a C e l b i s s o P n o i t c A e v i t ...

  • Pentair 4/160 - page 35

    29 IntelliFlo 4 Installation and User ’ s Guide Problems and Corrective Action (Continued) m e l b o r Pe s u a C e l b i s s o P n o i t c A e v i t c e r r o C s p i r t r e k a e r b t i u c r i C . y l d e t a e p e r d n a m r a l A o t r e f e R e c n e u q e s D E L g n i n r a w . 7 2 e g a p n o . t n e r r u c r o t o m e v i s s e c x ...

  • Pentair 4/160 - page 36

    30 IntelliFlo 4 Installation and User ’ s Guide Notes ...

  • Pentair 4/160 - page 37

    31 IntelliFlo 4 Installation and User ’ s Guide Notes ...

  • Pentair 4/160 - page 38

    32 IntelliFlo 4 Installation and User ’ s Guide Notes ...

  • Pentair 4/160 - page 39

    ...

  • Pentair 4/160 - page 40

    P/N 357269 - Rev B ...

Manufacturer Pentair Category Water Pump

Documents that we receive from a manufacturer of a Pentair 4/160 can be divided into several groups. They are, among others:
- Pentair technical drawings
- 4/160 manuals
- Pentair product data sheets
- information booklets
- or energy labels Pentair 4/160
All of them are important, but the most important information from the point of view of use of the device are in the user manual Pentair 4/160.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Pentair 4/160, service manual, brief instructions and user manuals Pentair 4/160. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Pentair 4/160.

Similar manuals

A complete manual for the device Pentair 4/160, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Pentair 4/160 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Pentair 4/160.

A complete Pentair manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Pentair 4/160 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Pentair 4/160, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Pentair 4/160, that we can find in the current document
3. Tips how to use the basic functions of the device Pentair 4/160 - which should help us in our first steps of using Pentair 4/160
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Pentair 4/160
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Pentair 4/160 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Pentair 4/160?

Use the form below

If you did not solve your problem by using a manual Pentair 4/160, ask a question using the form below. If a user had a similar problem with Pentair 4/160 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)