-
NEC MultiSync E232WMT - page 1
MultiSync E232WMT User’s Manual ...
-
NEC MultiSync E232WMT - page 2
Index W arning, Caution ........................................................................................................................................... English-1 Registration Information ................................................................................................................................ English-2 Recommended ...
-
NEC MultiSync E232WMT - page 3
English English-1 TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPT ACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULL Y INSER TED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOL T AGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SER ...
-
NEC MultiSync E232WMT - page 4
English-2 Registration Information FCC Information 1. Use the attached specied cables with the MultiSync E232WMT (L233QV) monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. Power supply c ...
-
NEC MultiSync E232WMT - page 5
English English-3 Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing ...
-
NEC MultiSync E232WMT - page 6
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Y our eyes should look slig ...
-
NEC MultiSync E232WMT - page 7
English English-5 Contents Y our new NEC monitor box* should contain the following: • MultiSync monitor with tilt/height adjust stand • Power Cord* 1 • Video Signal Cable (DVI-D to DVI-D cable)* 2 • Video Signal Cable (Mini D-SUB 15 pin to Mini D-SUB 15 pin) • USB Cable* 3 • Audio Cable (ø 3.5 stereo mini plug) • Setup Manual. Mini D ...
-
NEC MultiSync E232WMT - page 8
English-6 Quick Start T o connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended use” (page 3) before installation. 1. Turn of f the power of your computer . 2. For a PC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system ( Figure A.1 ). T igh ...
-
NEC MultiSync E232WMT - page 9
English English-7 3. Place hands on each side of the monitor to tilt the LCD panel and lift up to the highest position. NOTE: Handle with care when tilting the monitor screen. 4. Connect all cables to the appropriate connectors ( Figure C.1 ). For using the USB cable, connect the B type connector to the USB upstream port on the right back side of t ...
-
NEC MultiSync E232WMT - page 10
English-8 UP DOWN AUTO MENU POWER Figure E.1 LED Indicates that the power is on or off. LED The white light is lit up while the camera is in operation. Microphone Microphone Camera Raise and Lower Monitor Screen T o raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height ( Figure RL.1 ). NOTE: Handle ...
-
NEC MultiSync E232WMT - page 11
English English-9 Remove Monitor Stand for Mounting T o prepare the monitor for alternate mounting purposes: 1. Disconnect all cables. 2. Place a hand on each side of the monitor and lift up to the highest position. 3. Place monitor face down on a non-abrasive surface ( Figure S.1 ). NOTE: Handle with care when the monitor is facing down. 4. Remove ...
-
NEC MultiSync E232WMT - page 12
English-10 Controls OSD (On-Screen Display) control keys on the side of the monitor function are as follows: T o access OSD menu, press the MENU key . T o change signal input, press the AUTO/EXIT key . NOTE: Exit OSD in order to change signal input. UP DOWN AUTO MENU POWER 1 2 3 4 5 6 1 s / UP Navigates up or increases values through the OSD Contro ...
-
NEC MultiSync E232WMT - page 13
English English-1 1 BRIGHTNESS / CONTRAST Contrast (Only when Eco Mode Off) Adjusts the overall image and background screen brightness by input signal level. Brightness (Only when Eco Mode Off) Adjusts the overall image and background screen brightness. Eco Mode Decreases the amount of power consumption by reducing the brightness level. Off : No fu ...
-
NEC MultiSync E232WMT - page 14
English-12 OSD Setup Timeout Y ou can select how long the monitor waits after the last touch of a key to shut of f the OSD menu. Language Selects the language used by the OSD. Extra Input Select Changes the video input source. Reset Allows you to reset all OSD control settings back to the factory settings. Information Provides information about the ...
-
NEC MultiSync E232WMT - page 15
English English-13 Specications Monitor Specications MultiSync E232WMT Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 58.42 cm/23.0 inches 58.42 cm/23.0 inches 1920 x 1080 Active matrix; thin lm transistor (TFT) liquid crystal display (LCD); 0.265 mm dot pitch; 250 cd/m 2 white luminance; 1000:1 contrast r ...
-
NEC MultiSync E232WMT - page 16
English-14 T roubleshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a ...
-
NEC MultiSync E232WMT - page 17
English English-15 USB Hub does not operate • Check to make sure the USB cable is properly connected. Refer to your USB devise User’s Manual. • Check if the USB upstream port on the monitor is connected to the USB downstream port on the computer . And make sure the computer is ON. The touch panel does not work • Check to make sure the USB c ...
-
NEC MultiSync E232WMT - page 18
English-16 TCO Certied Displays 6 Congratulations! This product is TCO Certied – for Sustainable IT TCO Certied is an international third party sustainability certication for IT products. TCO Certied ensures that the manufacture, use and recycling of IT products reect environmental, social and economic responsibility . Every TCO ...
-
NEC MultiSync E232WMT - page 19
English English-17 Manufacturer’s Recycling and Energy Information NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly products, and always strive to hel ...
Do you have a question concerning NEC MultiSync E232WMT?
Use the form below
If you did not solve your problem by using a manual NEC MultiSync E232WMT, ask a question using the form below. If a user had a similar problem with NEC MultiSync E232WMT it is likely that he will want to share the way to solve it.