Deutsch dropdown-ico

Bedienungsanleitung Alto-Shaam 4.10ESi

28 Seiten 2.35 mb
Download

Zur Seite of 28

Summary
  • Alto-Shaam 4.10ESi - page 1

    MN-29805 • 08/12 printed i n u . s . a . Combitherm ® Combination Oven / Steamer CT EXPRESS™ 4•10es i 4•10esiVH   • InstallatIon W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.251.3800 • 800.558.8744 u s a / c a N a d a FaX: 262.251.7067 • 800.329.8744 u . s . a . O N l y ww ...

  • Alto-Shaam 4.10ESi - page 2

    i Delivery .................................. 1 Unpacking ................................ 1 Safety Procedures and Precautions ............. 2 Installation Site Installation .......................... 3 Ventilation Requirements ................... 3 Positioning on Site ........................ 4 Lifting Instructions ........................ 5 Level ...

  • Alto-Shaam 4.10ESi - page 3

     INSTALLATION MANUAL • 1. DELIVERY This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in th ...

  • Alto-Shaam 4.10ESi - page 4

     INSTALLATION MANUAL • 2. CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored. CAUTION Used to indicate the presence of a hazard that can or will cause minor or moderate p ...

  • Alto-Shaam 4.10ESi - page 5

     INSTALLATION MANUAL • 3. SITE INSTALLATION INSTALLATION DANGER IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, SERVICE, OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH, OR CAUSE PROPERTY DAMAGE. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPME ...

  • Alto-Shaam 4.10ESi - page 6

     INSTALLATION MANUAL • 4. NOTE: Note dimensions required for doorways and aisles for access of the oven and pallet to the installation site. Transport the oven in an upright and level position only. Do not tilt the oven. ® SITE INSTALLATION INSTALLATION POSITIONING ON SITE Stand the oven in a level position. Use ...

  • Alto-Shaam 4.10ESi - page 7

     INSTALLATION MANUAL • 5. LIFTING INSTRUCTIONS INSTALLATION Remove banding before lifting. Lift the unit from either side of the unit, never from the front o r back . Adjust the forks so that they do not damage any of the components under the unit. Air intake vents are located in front of the legs and must not be ...

  • Alto-Shaam 4.10ESi - page 8

     INSTALLATION MANUAL • 6. SITE INSTALLATION INSTALLATION EXHAUST VENT 18" (46cm) 4" (102mm) 4" (102mm) 20" (50cm) MINIMUM 20" (50cm) POSITIONING REQUIREMENTS q In order to ensure proper ventilation, a minimum distance of at least 4-inches (101mm) must be kept from the sides of the oven and ...

  • Alto-Shaam 4.10ESi - page 9

     INSTALLATION MANUAL • 7. ACCESSORIES CombiClean® Tablets — CE-28892 s P E c i a l l y F O r M u l a t E d FOr cOMbitHErM OvENs ➥ t w O (2) c O N t a i N E r s / bOX , 90 PackEts E a c H c O N t a i N E r Combitherm Cleaning Liquid — CE-24750 s P E c i a l l y F O r M u l a t E d FOr cOMbitHErM OvENs ➥ t ...

  • Alto-Shaam 4.10ESi - page 10

     INSTALLATION MANUAL • 8. WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS ONE (1) COLD W A TER INLETS - DRINKING QUALITY ONE (1) W A TER INLET : 3/4" G* LI NE PR ES SU RE: 30 to 90 psi 2.8 to 6.2 bar W A TER DRAIN: 1-1/2" CONNECTION WITH A 2" MINIMUM AIR GAP INST ALLED AS CLOSE TO THE OVEN AS POS ...

  • Alto-Shaam 4.10ESi - page 11

     INSTALLATION MANUAL • 9. WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS ONE (1) COLD W A TER INLETS - DRINKING QUALITY ONE (1) W A TER INLET : 3/4" G* LI NE PR ES SU RE: 30 to 90 psi 2.8 to 6.2 bar W A TER DRAIN: 1-1/2" CONNECTION WITH A 2" MINIMUM AIR GAP INST ALLED AS CLOSE TO THE OVEN AS POS ...

  • Alto-Shaam 4.10ESi - page 12

     INSTALLATION MANUAL •  ELECTRICAL CONNECTION INSTALLATION DANGER ENSURE POWER SOURCE MATCHES VOLTAGE IDENTIFIED ON APPLIANCE RATING TAG. DANGER To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the curre ...

  • Alto-Shaam 4.10ESi - page 13

     INSTALLATION MANUAL • 11. ELECTRICAL CONNECTION INSTALLATION DANGER ELECTRICAL CONNECTIONS MUST BE MADE BY A QUALIFIED SERVICE TECHNICIAN IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES. INTERNAL GROUND STUD CUSTOMER MUST SUPPLY CORD INCOMING ELECTRICAL TERMINALS APPLIES TO 208-240V & 380-415V UNITS L1 L2 L3 N ...

  • Alto-Shaam 4.10ESi - page 14

     INSTALLATION MANUAL • 12. MOBILE EQUIPMENT RESTRAINT INSTALLATION Any appliance that is not furnished with a power supply cord but includes a set of casters, stand with casters, or a stacked configuration must be installed with a tether. Adequate means must be provided to limit the movement of this appliance with ...

  • Alto-Shaam 4.10ESi - page 15

     INSTALLATION MANUAL • 13. INSTALLATION WATER QUALITY REQUIREMENT WARNING TO PREVENT WATER PIPES FROM BURSTING, INCOMING WATER SUPPLY SHOULD BE TURNED OFF WHEN THE APPLIANCE IS NOT IN USE. WARNING WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATED. VERIFY WATER SUPPLY BEFORE STARTING CLEANING PROGRAM. US ...

  • Alto-Shaam 4.10ESi - page 16

     INSTALLATION MANUAL • 14. INSTALLATION WATER CONNECTIONS WATER SUPPLY & INSTALLATION WATER REQUIREMENTS ONE (1) COLD WATER INLET - DRINKING QUALITY ONE (1) TREATED WATER INLET: 3/4" G LINE PRESSURE: 30 to 90 psi 2.8 to 6.2 bar REFER TO PUBLISHED SPECIFIC W A TER REQUIREMENTS WATER DRAIN: 1-1/2" CONN ...

  • Alto-Shaam 4.10ESi - page 17

     INSTALLATION MANUAL • 15. INSTALLATION OPTIONAL HAND HELD SPRAY HOSE V alve bracket INSTALLATION 1 Using the valve bracket as a template for placement, and a #28 drill bit (0.14" diameter), drill two holes at the lower rear side of the unit (same side as door opening). Fasten the valve bracket using the 2 se ...

  • Alto-Shaam 4.10ESi - page 18

     INSTALLATION MANUAL • 16. INSTALLATION WATER VALVE WATER DRAINAGE NOTE: THE SHUT-OFF VALVE MUST BE IN THE OPEN POSITION WHEN THE OVEN IS BEING USED. The oven must discharge through an indirect waste pipe by means of an air gap. The drain fitting is supplied with a 1-1/2-inch (38mm) NPT thread. A union is required ...

  • Alto-Shaam 4.10ESi - page 19

     INSTALLATION MANUAL • 17. INDICATOR LIGHT If the indicator light does not illuminate, the filters may be missing or not properly aligned. Check them for proper positioning. Ventless hood and oven will not operate unless the hood is closed properly. INSTALLATION VENTLESS HOOD MODEL The Ventless Hood option is fact ...

  • Alto-Shaam 4.10ESi - page 20

     INSTALLATION MANUAL • 18. INSTALLATION VENTLESS HOOD MODEL TOP EXHAUST VENT 1 Charcoal Filter: The charcoal filter should be inspected for contaminant's on a regular basis. Replacement must be made at a minimum of three month intervals — more often if heavy contaminant's are visible or if the filter n ...

  • Alto-Shaam 4.10ESi - page 21

     INSTALLATION MANUAL • 19. INSTALLATION CT EXPRESS™ CHECKLIST Use this list as a nal check of oven installation conformance. Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims. CLEARANCES: Left: 4" (152mm) — Service access of 18" (457mm) recomme ...

  • Alto-Shaam 4.10ESi - page 22

     INSTALLATION MANUAL •  continued on next page ERROR CODES This section is provided for the assistance of qualified technicians only and is not intended for use by untrained or unauthorized service personnel. If your Alto-Shaam ® unit is not operating properly , check the following before calling your Au ...

  • Alto-Shaam 4.10ESi - page 23

     INSTALLATION MANUAL • 21. continued on next page ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E13   — Scale build up in ...

  • Alto-Shaam 4.10ESi - page 24

     INSTALLATION MANUAL • 22. ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E34 Steam Generator Drain  Water level in steam generator does not drop during cleaning program  ? ...

  • Alto-Shaam 4.10ESi - page 25

     INSTALLATION MANUAL • 23. ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E57 No Rinse Water During rinse no water    solenoid valve  ? ...

  • Alto-Shaam 4.10ESi - page 26

     INSTALLATION MANUAL • 24. ERROR CODES When the oven malfunctions, an error code will appear in the display . PRESS THE ST AR T ICON TO ACKNOWLEDGE THE ERROR. The icons that begin to flash repr esent operational modes that are still usable. When the oven fault is corrected, the Combitherm will r eturn to normal op ...

  • Alto-Shaam 4.10ESi - page 27

     INSTALLATION MANUAL • 25. ORIGINAL EQUIPMENT LIMITED WARRANTY Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part. The la ...

  • Alto-Shaam 4.10ESi - page 28

    TRANSPORTATION DAMAGE AND CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the me ...

Produzent Alto-Shaam Kategorie Oven

Dokumente, die wir vom Produzenten des Geräts Alto-Shaam 4.10ESi erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Alto-Shaam
- Bedienungsanleitungen 4.10ESi
- Produktkarten Alto-Shaam
- Informationsbroschüren
- oder Energieetiketten Alto-Shaam 4.10ESi
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Alto-Shaam 4.10ESi.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Alto-Shaam 4.10ESi, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Alto-Shaam 4.10ESi. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Alto-Shaam 4.10ESi ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Alto-Shaam 4.10ESi, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Alto-Shaam 4.10ESi hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Alto-Shaam 4.10ESi verständlich ist.

Eine gänzliche Bedienungsanleitung von Alto-Shaam sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Alto-Shaam 4.10ESi bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Alto-Shaam 4.10ESi befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Alto-Shaam 4.10ESi, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Alto-Shaam 4.10ESi - die uns die ersten Schritte während der Nutzung von Alto-Shaam 4.10ESi erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Alto-Shaam 4.10ESi hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Alto-Shaam 4.10ESi im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Alto-Shaam 4.10ESi?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Alto-Shaam 4.10ESi nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Alto-Shaam 4.10ESi hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)