Français dropdown-ico

Manuel d’utilisation Alto-Shaam 4.10ESi

28 pages 2.35 mb
Télécharger

Aller à la page of 28

Summary
  • Alto-Shaam 4.10ESi - page 1

    MN-29805 • 08/12 printed i n u . s . a . Combitherm ® Combination Oven / Steamer CT EXPRESS™ 4•10es i 4•10esiVH   • InstallatIon W164 N9221 Water Street • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA PHONE: 262.251.3800 • 800.558.8744 u s a / c a N a d a FaX: 262.251.7067 • 800.329.8744 u . s . a . O N l y ww ...

  • Alto-Shaam 4.10ESi - page 2

    i Delivery .................................. 1 Unpacking ................................ 1 Safety Procedures and Precautions ............. 2 Installation Site Installation .......................... 3 Ventilation Requirements ................... 3 Positioning on Site ........................ 4 Lifting Instructions ........................ 5 Level ...

  • Alto-Shaam 4.10ESi - page 3

     INSTALLATION MANUAL • 1. DELIVERY This Alto-Shaam appliance has been thoroughly tested and inspected to ensure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in th ...

  • Alto-Shaam 4.10ESi - page 4

     INSTALLATION MANUAL • 2. CAUTION Used to indicate the presence of a hazard that can or will cause minor personal injury, property damage, or a potential unsafe practice if the warning included with this symbol is ignored. CAUTION Used to indicate the presence of a hazard that can or will cause minor or moderate p ...

  • Alto-Shaam 4.10ESi - page 5

     INSTALLATION MANUAL • 3. SITE INSTALLATION INSTALLATION DANGER IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, SERVICE, OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH, OR CAUSE PROPERTY DAMAGE. READ THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPME ...

  • Alto-Shaam 4.10ESi - page 6

     INSTALLATION MANUAL • 4. NOTE: Note dimensions required for doorways and aisles for access of the oven and pallet to the installation site. Transport the oven in an upright and level position only. Do not tilt the oven. ® SITE INSTALLATION INSTALLATION POSITIONING ON SITE Stand the oven in a level position. Use ...

  • Alto-Shaam 4.10ESi - page 7

     INSTALLATION MANUAL • 5. LIFTING INSTRUCTIONS INSTALLATION Remove banding before lifting. Lift the unit from either side of the unit, never from the front o r back . Adjust the forks so that they do not damage any of the components under the unit. Air intake vents are located in front of the legs and must not be ...

  • Alto-Shaam 4.10ESi - page 8

     INSTALLATION MANUAL • 6. SITE INSTALLATION INSTALLATION EXHAUST VENT 18" (46cm) 4" (102mm) 4" (102mm) 20" (50cm) MINIMUM 20" (50cm) POSITIONING REQUIREMENTS q In order to ensure proper ventilation, a minimum distance of at least 4-inches (101mm) must be kept from the sides of the oven and ...

  • Alto-Shaam 4.10ESi - page 9

     INSTALLATION MANUAL • 7. ACCESSORIES CombiClean® Tablets — CE-28892 s P E c i a l l y F O r M u l a t E d FOr cOMbitHErM OvENs ➥ t w O (2) c O N t a i N E r s / bOX , 90 PackEts E a c H c O N t a i N E r Combitherm Cleaning Liquid — CE-24750 s P E c i a l l y F O r M u l a t E d FOr cOMbitHErM OvENs ➥ t ...

  • Alto-Shaam 4.10ESi - page 10

     INSTALLATION MANUAL • 8. WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS ONE (1) COLD W A TER INLETS - DRINKING QUALITY ONE (1) W A TER INLET : 3/4" G* LI NE PR ES SU RE: 30 to 90 psi 2.8 to 6.2 bar W A TER DRAIN: 1-1/2" CONNECTION WITH A 2" MINIMUM AIR GAP INST ALLED AS CLOSE TO THE OVEN AS POS ...

  • Alto-Shaam 4.10ESi - page 11

     INSTALLATION MANUAL • 9. WATER REQUIREMENTS WATER QUALITY MINIMUM STANDARDS ONE (1) COLD W A TER INLETS - DRINKING QUALITY ONE (1) W A TER INLET : 3/4" G* LI NE PR ES SU RE: 30 to 90 psi 2.8 to 6.2 bar W A TER DRAIN: 1-1/2" CONNECTION WITH A 2" MINIMUM AIR GAP INST ALLED AS CLOSE TO THE OVEN AS POS ...

  • Alto-Shaam 4.10ESi - page 12

     INSTALLATION MANUAL •  ELECTRICAL CONNECTION INSTALLATION DANGER ENSURE POWER SOURCE MATCHES VOLTAGE IDENTIFIED ON APPLIANCE RATING TAG. DANGER To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the curre ...

  • Alto-Shaam 4.10ESi - page 13

     INSTALLATION MANUAL • 11. ELECTRICAL CONNECTION INSTALLATION DANGER ELECTRICAL CONNECTIONS MUST BE MADE BY A QUALIFIED SERVICE TECHNICIAN IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES. INTERNAL GROUND STUD CUSTOMER MUST SUPPLY CORD INCOMING ELECTRICAL TERMINALS APPLIES TO 208-240V & 380-415V UNITS L1 L2 L3 N ...

  • Alto-Shaam 4.10ESi - page 14

     INSTALLATION MANUAL • 12. MOBILE EQUIPMENT RESTRAINT INSTALLATION Any appliance that is not furnished with a power supply cord but includes a set of casters, stand with casters, or a stacked configuration must be installed with a tether. Adequate means must be provided to limit the movement of this appliance with ...

  • Alto-Shaam 4.10ESi - page 15

     INSTALLATION MANUAL • 13. INSTALLATION WATER QUALITY REQUIREMENT WARNING TO PREVENT WATER PIPES FROM BURSTING, INCOMING WATER SUPPLY SHOULD BE TURNED OFF WHEN THE APPLIANCE IS NOT IN USE. WARNING WATER SUPPLY MUST BE OPEN WHEN CLEANING PROGRAM IS ACTIVATED. VERIFY WATER SUPPLY BEFORE STARTING CLEANING PROGRAM. US ...

  • Alto-Shaam 4.10ESi - page 16

     INSTALLATION MANUAL • 14. INSTALLATION WATER CONNECTIONS WATER SUPPLY & INSTALLATION WATER REQUIREMENTS ONE (1) COLD WATER INLET - DRINKING QUALITY ONE (1) TREATED WATER INLET: 3/4" G LINE PRESSURE: 30 to 90 psi 2.8 to 6.2 bar REFER TO PUBLISHED SPECIFIC W A TER REQUIREMENTS WATER DRAIN: 1-1/2" CONN ...

  • Alto-Shaam 4.10ESi - page 17

     INSTALLATION MANUAL • 15. INSTALLATION OPTIONAL HAND HELD SPRAY HOSE V alve bracket INSTALLATION 1 Using the valve bracket as a template for placement, and a #28 drill bit (0.14" diameter), drill two holes at the lower rear side of the unit (same side as door opening). Fasten the valve bracket using the 2 se ...

  • Alto-Shaam 4.10ESi - page 18

     INSTALLATION MANUAL • 16. INSTALLATION WATER VALVE WATER DRAINAGE NOTE: THE SHUT-OFF VALVE MUST BE IN THE OPEN POSITION WHEN THE OVEN IS BEING USED. The oven must discharge through an indirect waste pipe by means of an air gap. The drain fitting is supplied with a 1-1/2-inch (38mm) NPT thread. A union is required ...

  • Alto-Shaam 4.10ESi - page 19

     INSTALLATION MANUAL • 17. INDICATOR LIGHT If the indicator light does not illuminate, the filters may be missing or not properly aligned. Check them for proper positioning. Ventless hood and oven will not operate unless the hood is closed properly. INSTALLATION VENTLESS HOOD MODEL The Ventless Hood option is fact ...

  • Alto-Shaam 4.10ESi - page 20

     INSTALLATION MANUAL • 18. INSTALLATION VENTLESS HOOD MODEL TOP EXHAUST VENT 1 Charcoal Filter: The charcoal filter should be inspected for contaminant's on a regular basis. Replacement must be made at a minimum of three month intervals — more often if heavy contaminant's are visible or if the filter n ...

  • Alto-Shaam 4.10ESi - page 21

     INSTALLATION MANUAL • 19. INSTALLATION CT EXPRESS™ CHECKLIST Use this list as a nal check of oven installation conformance. Damage directly attributed to improper set up, installation, or cleaning can invalidate warranty claims. CLEARANCES: Left: 4" (152mm) — Service access of 18" (457mm) recomme ...

  • Alto-Shaam 4.10ESi - page 22

     INSTALLATION MANUAL •  continued on next page ERROR CODES This section is provided for the assistance of qualified technicians only and is not intended for use by untrained or unauthorized service personnel. If your Alto-Shaam ® unit is not operating properly , check the following before calling your Au ...

  • Alto-Shaam 4.10ESi - page 23

     INSTALLATION MANUAL • 21. continued on next page ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E13   — Scale build up in ...

  • Alto-Shaam 4.10ESi - page 24

     INSTALLATION MANUAL • 22. ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E34 Steam Generator Drain  Water level in steam generator does not drop during cleaning program  ? ...

  • Alto-Shaam 4.10ESi - page 25

     INSTALLATION MANUAL • 23. ERROR CODES Error Code Error Call Out in Display Description of Error Possible Cause E57 No Rinse Water During rinse no water    solenoid valve  ? ...

  • Alto-Shaam 4.10ESi - page 26

     INSTALLATION MANUAL • 24. ERROR CODES When the oven malfunctions, an error code will appear in the display . PRESS THE ST AR T ICON TO ACKNOWLEDGE THE ERROR. The icons that begin to flash repr esent operational modes that are still usable. When the oven fault is corrected, the Combitherm will r eturn to normal op ...

  • Alto-Shaam 4.10ESi - page 27

     INSTALLATION MANUAL • 25. ORIGINAL EQUIPMENT LIMITED WARRANTY Alto-Shaam, Inc. warrants to the original purchaser that any original part that is found to be defective in material or workmanship will, at Alto-Shaam’s option, subject to provisions hereinafter stated, be replaced with a new or rebuilt part. The la ...

  • Alto-Shaam 4.10ESi - page 28

    TRANSPORTATION DAMAGE AND CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the me ...

Fabricant Alto-Shaam Catégorie Oven

Les documents que nous recevons du fabricant de l'appareilAlto-Shaam 4.10ESi peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Alto-Shaam
- manuels d’utilisations 4.10ESi
- fiches produit Alto-Shaam
- dépliants
- ou étiquettes-énergie Alto-Shaam 4.10ESi
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Alto-Shaam 4.10ESi.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Alto-Shaam 4.10ESi, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Alto-Shaam 4.10ESi. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Alto-Shaam 4.10ESi.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Alto-Shaam 4.10ESi, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Alto-Shaam 4.10ESi par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Alto-Shaam 4.10ESi.

Le manuel d’utilisation complet Alto-Shaam, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Alto-Shaam 4.10ESi - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Alto-Shaam 4.10ESi, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lAlto-Shaam 4.10ESi qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Alto-Shaam 4.10ESi - qui devraient nous aider dans les premières étapes lors de l'utilisation Alto-Shaam 4.10ESi
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Alto-Shaam 4.10ESi
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Alto-Shaam 4.10ESi dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Alto-Shaam 4.10ESi?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Alto-Shaam 4.10ESi, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Alto-Shaam 4.10ESi il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)