Bedienungsanleitung Ingersoll-Rand 7153-C

11 Seiten 0.86 mb
Download

Zur Seite of 11

Summary
  • Ingersoll-Rand 7153-C - page 1

    OPERATOR’S MANUAL SECTION M10 MANUAL 43 Released: 5/79 INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “22” SERIES SHORT GRINDERS Revised: 1 O-20-95 Form: 1566-2 Models: 7149-C, 7153-C, 7235-C and 7236-C READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RE ...

  • Ingersoll-Rand 7153-C - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. m Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Air powered tools can vibrate In use. Vibration, repetitive motions or uncomfortable positions may be harmful t ...

  • Ingersoll-Rand 7153-C - page 3

    ROUTINE LUBRICATION REQUIREMENTS Ml0 43 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not ...

  • Ingersoll-Rand 7153-C - page 4

    The grinder models listed in the model identification table above arefurnished with collet assembly 41753-3 (1/4”capacity) as standard equipment and are intended for use with mounted wheels and shall not be used with othertype grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer, is attached to thegrinder. See ”G ...

  • Ingersoll-Rand 7153-C - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 43 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or chipped ...

  • Ingersoll-Rand 7153-C - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and lnstal- lation” section. To minimize the ...

  • Ingersoll-Rand 7153-C - page 7

    MOTOR SECTION M10 43 DISASSEMBLY Remove motor from housing (see page 6). Grasp cylinder in one race of bearing. Assemble cylinder over rotor, aligning air inlets of hand and tap threaded end of rotor with a soft face hammer; motor cylinder and end plate and roll pin (Y17B-20) with hole in end will come apart. plate (largest hole). Assemble blades t ...

  • Ingersoll-Rand 7153-C - page 8

    HEAD SECTION DISASSEMBLY ASSEMBLY Remove valve plug (30600) and valve components can be re- moved from head. To remove lever throttle, remove roll pin (Y178-28). To remove button throttle, remove roll pin (Y178-212). Assemble “O” ring (Y325-7) to valve stem. Assemble valve stem into head. Assemble spring (30609) and regulator (30603) into head, ...

  • Ingersoll-Rand 7153-C - page 9

    ACCES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLET SUE COLLET , ASSEMBLY NO. INSERT NO. , 41753-I 1/8” 41750-1 41753-2 3/16 41750-2 41753-3 1/4” 41750-3 41753-11 3 mm 41750-11 41753-12 6 mm 41750-12 COLLET NUT - 41751 COLLET NUT DIA. - 3/4” COLLET BODY - 41752 COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD OVER ALL LENGTH - 2 1/4” 44127-( ) ERI ...

  • Ingersoll-Rand 7153-C - page 10

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDITION LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE 1. DAMAGED VALVE PIN OR COM- ...

  • Ingersoll-Rand 7153-C - page 11

    Part of worldwide Ingersoll-Rand ...

Produzent Ingersoll-Rand Kategorie Grinder

Dokumente, die wir vom Produzenten des Geräts Ingersoll-Rand 7153-C erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Ingersoll-Rand
- Bedienungsanleitungen 7153-C
- Produktkarten Ingersoll-Rand
- Informationsbroschüren
- oder Energieetiketten Ingersoll-Rand 7153-C
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Ingersoll-Rand 7153-C.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Ingersoll-Rand 7153-C, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Ingersoll-Rand 7153-C. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Ingersoll-Rand 7153-C ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Ingersoll-Rand 7153-C, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Ingersoll-Rand 7153-C hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Ingersoll-Rand 7153-C verständlich ist.

Eine gänzliche Bedienungsanleitung von Ingersoll-Rand sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Ingersoll-Rand 7153-C bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Ingersoll-Rand 7153-C befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Ingersoll-Rand 7153-C, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Ingersoll-Rand 7153-C - die uns die ersten Schritte während der Nutzung von Ingersoll-Rand 7153-C erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Ingersoll-Rand 7153-C hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Ingersoll-Rand 7153-C im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Ingersoll-Rand 7153-C?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Ingersoll-Rand 7153-C nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Ingersoll-Rand 7153-C hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)