English dropdown-ico

Manual Ingersoll-Rand 7153-C

11 pages 0.86 mb
Download

Go to site of 11

Summary
  • Ingersoll-Rand 7153-C - page 1

    OPERATOR’S MANUAL SECTION M10 MANUAL 43 Released: 5/79 INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “22” SERIES SHORT GRINDERS Revised: 1 O-20-95 Form: 1566-2 Models: 7149-C, 7153-C, 7235-C and 7236-C READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RE ...

  • Ingersoll-Rand 7153-C - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. m Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Air powered tools can vibrate In use. Vibration, repetitive motions or uncomfortable positions may be harmful t ...

  • Ingersoll-Rand 7153-C - page 3

    ROUTINE LUBRICATION REQUIREMENTS Ml0 43 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not ...

  • Ingersoll-Rand 7153-C - page 4

    The grinder models listed in the model identification table above arefurnished with collet assembly 41753-3 (1/4”capacity) as standard equipment and are intended for use with mounted wheels and shall not be used with othertype grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer, is attached to thegrinder. See ”G ...

  • Ingersoll-Rand 7153-C - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 43 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or chipped ...

  • Ingersoll-Rand 7153-C - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and lnstal- lation” section. To minimize the ...

  • Ingersoll-Rand 7153-C - page 7

    MOTOR SECTION M10 43 DISASSEMBLY Remove motor from housing (see page 6). Grasp cylinder in one race of bearing. Assemble cylinder over rotor, aligning air inlets of hand and tap threaded end of rotor with a soft face hammer; motor cylinder and end plate and roll pin (Y17B-20) with hole in end will come apart. plate (largest hole). Assemble blades t ...

  • Ingersoll-Rand 7153-C - page 8

    HEAD SECTION DISASSEMBLY ASSEMBLY Remove valve plug (30600) and valve components can be re- moved from head. To remove lever throttle, remove roll pin (Y178-28). To remove button throttle, remove roll pin (Y178-212). Assemble “O” ring (Y325-7) to valve stem. Assemble valve stem into head. Assemble spring (30609) and regulator (30603) into head, ...

  • Ingersoll-Rand 7153-C - page 9

    ACCES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLET SUE COLLET , ASSEMBLY NO. INSERT NO. , 41753-I 1/8” 41750-1 41753-2 3/16 41750-2 41753-3 1/4” 41750-3 41753-11 3 mm 41750-11 41753-12 6 mm 41750-12 COLLET NUT - 41751 COLLET NUT DIA. - 3/4” COLLET BODY - 41752 COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD OVER ALL LENGTH - 2 1/4” 44127-( ) ERI ...

  • Ingersoll-Rand 7153-C - page 10

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDITION LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE 1. DAMAGED VALVE PIN OR COM- ...

  • Ingersoll-Rand 7153-C - page 11

    Part of worldwide Ingersoll-Rand ...

Manufacturer Ingersoll-Rand Category Grinder

Documents that we receive from a manufacturer of a Ingersoll-Rand 7153-C can be divided into several groups. They are, among others:
- Ingersoll-Rand technical drawings
- 7153-C manuals
- Ingersoll-Rand product data sheets
- information booklets
- or energy labels Ingersoll-Rand 7153-C
All of them are important, but the most important information from the point of view of use of the device are in the user manual Ingersoll-Rand 7153-C.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Ingersoll-Rand 7153-C, service manual, brief instructions and user manuals Ingersoll-Rand 7153-C. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Ingersoll-Rand 7153-C.

Similar manuals

A complete manual for the device Ingersoll-Rand 7153-C, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Ingersoll-Rand 7153-C by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Ingersoll-Rand 7153-C.

A complete Ingersoll-Rand manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Ingersoll-Rand 7153-C - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Ingersoll-Rand 7153-C, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Ingersoll-Rand 7153-C, that we can find in the current document
3. Tips how to use the basic functions of the device Ingersoll-Rand 7153-C - which should help us in our first steps of using Ingersoll-Rand 7153-C
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Ingersoll-Rand 7153-C
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Ingersoll-Rand 7153-C in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Ingersoll-Rand 7153-C?

Use the form below

If you did not solve your problem by using a manual Ingersoll-Rand 7153-C, ask a question using the form below. If a user had a similar problem with Ingersoll-Rand 7153-C it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)