Manuel d’utilisation Ingersoll-Rand 7153-C

11 pages 0.86 mb
Télécharger

Aller à la page of 11

Summary
  • Ingersoll-Rand 7153-C - page 1

    OPERATOR’S MANUAL SECTION M10 MANUAL 43 Released: 5/79 INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “22” SERIES SHORT GRINDERS Revised: 1 O-20-95 Form: 1566-2 Models: 7149-C, 7153-C, 7235-C and 7236-C READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT. FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RE ...

  • Ingersoll-Rand 7153-C - page 2

    FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. m Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Air powered tools can vibrate In use. Vibration, repetitive motions or uncomfortable positions may be harmful t ...

  • Ingersoll-Rand 7153-C - page 3

    ROUTINE LUBRICATION REQUIREMENTS Ml0 43 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.R.L. with spindle oil (29665). If an in line or air line lubricator is not ...

  • Ingersoll-Rand 7153-C - page 4

    The grinder models listed in the model identification table above arefurnished with collet assembly 41753-3 (1/4”capacity) as standard equipment and are intended for use with mounted wheels and shall not be used with othertype grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer, is attached to thegrinder. See ”G ...

  • Ingersoll-Rand 7153-C - page 5

    GRINDING WHEEL MOUNTING INSTRUCTIONS M10 43 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool. Check abrasive wheels prior to mounting for chips or cracks. Cracked or chipped ...

  • Ingersoll-Rand 7153-C - page 6

    DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and lnstal- lation” section. To minimize the ...

  • Ingersoll-Rand 7153-C - page 7

    MOTOR SECTION M10 43 DISASSEMBLY Remove motor from housing (see page 6). Grasp cylinder in one race of bearing. Assemble cylinder over rotor, aligning air inlets of hand and tap threaded end of rotor with a soft face hammer; motor cylinder and end plate and roll pin (Y17B-20) with hole in end will come apart. plate (largest hole). Assemble blades t ...

  • Ingersoll-Rand 7153-C - page 8

    HEAD SECTION DISASSEMBLY ASSEMBLY Remove valve plug (30600) and valve components can be re- moved from head. To remove lever throttle, remove roll pin (Y178-28). To remove button throttle, remove roll pin (Y178-212). Assemble “O” ring (Y325-7) to valve stem. Assemble valve stem into head. Assemble spring (30609) and regulator (30603) into head, ...

  • Ingersoll-Rand 7153-C - page 9

    ACCES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLET SUE COLLET , ASSEMBLY NO. INSERT NO. , 41753-I 1/8” 41750-1 41753-2 3/16 41750-2 41753-3 1/4” 41750-3 41753-11 3 mm 41750-11 41753-12 6 mm 41750-12 COLLET NUT - 41751 COLLET NUT DIA. - 3/4” COLLET BODY - 41752 COLLET BODY DIA. - 21/32” 3/8” - 24 THREAD OVER ALL LENGTH - 2 1/4” 44127-( ) ERI ...

  • Ingersoll-Rand 7153-C - page 10

    TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDITION LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN. THROTTLE VALVE 1. DAMAGED VALVE PIN OR COM- ...

  • Ingersoll-Rand 7153-C - page 11

    Part of worldwide Ingersoll-Rand ...

Fabricant Ingersoll-Rand Catégorie Grinder

Les documents que nous recevons du fabricant de l'appareilIngersoll-Rand 7153-C peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Ingersoll-Rand
- manuels d’utilisations 7153-C
- fiches produit Ingersoll-Rand
- dépliants
- ou étiquettes-énergie Ingersoll-Rand 7153-C
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Ingersoll-Rand 7153-C.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Ingersoll-Rand 7153-C, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Ingersoll-Rand 7153-C. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Ingersoll-Rand 7153-C.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Ingersoll-Rand 7153-C, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Ingersoll-Rand 7153-C par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Ingersoll-Rand 7153-C.

Le manuel d’utilisation complet Ingersoll-Rand, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Ingersoll-Rand 7153-C - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Ingersoll-Rand 7153-C, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lIngersoll-Rand 7153-C qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Ingersoll-Rand 7153-C - qui devraient nous aider dans les premières étapes lors de l'utilisation Ingersoll-Rand 7153-C
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Ingersoll-Rand 7153-C
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Ingersoll-Rand 7153-C dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Ingersoll-Rand 7153-C?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Ingersoll-Rand 7153-C, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Ingersoll-Rand 7153-C il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)