Bedienungsanleitung Standard Horizon DS41

17 Seiten 0.32 mb
Download

Zur Seite of 17

Summary
  • Standard Horizon DS41 - page 1

    DS41 Digital Depth Sounder Owner’ s Manual Standard 2 Inch Installation Dual Station Operation NMEA Repeater Reads in Feet Fathoms or Meters Adjustable Prop or Surface Offset Shallow and Deep alarms Dual Station Operation ...

  • Standard Horizon DS41 - page 2

    DS41 Owner’s Manual DS41 Owner’s Manual DS41/HS/2G Contents Specifications ................................................................................................................. 2 Operation ...................................................................................................................... .. 3 Alarms .............. ...

  • Standard Horizon DS41 - page 3

    DS41 Owner’s Manual 2 Specifications • Size Mount 2" (51mm) diameter hole Depth behind face plate 3.75" (95mm) max. Display 3-character LCD • Color Black with texture on bezel. • Backlighting Red colored diffused lighting for displa y . • Water Integrity F ront will withstand direct water spra y . • Depth/Alarm Range 2.0 ! 600 ...

  • Standard Horizon DS41 - page 4

    DS41 Owner’s Manual 3 Operation Whenever power is applied the depth sounder is active and water depth is displayed. If the sonar signal does not show a bottom the display will indicate “- -”. This can occur if the water is aerated or the maximum depth is exceeded. Note: The maximum depth decreases as boat speed increases. Alarms T wo types of ...

  • Standard Horizon DS41 - page 5

    DS41 Owner ’ s Manual 4 Deep Alarm T o set the deep alar m: 1. Press the # ke y for three seconds. The display will show: dAL OFF OFF ON ^ V V 2. After two seconds the display will indicate the current Deep Alarm depth setting. 8 8 50 3. Use the " and # keys to change the value. If either key is held depressed for more than one second the re ...

  • Standard Horizon DS41 - page 6

    DS41 Owner ’ s Manual 5 4. Use the " and # keys to change the value. If either key is held depressed for more than one second the reading will increase or decrease rapidly . 5. The offset can be programmed in 0.1 unit steps from -9.9 ! 9.9 feet (or equivalent). When programmed f or a negative offset, ‘ - ’ will be indicated on the left h ...

  • Standard Horizon DS41 - page 7

    DS41 Owner ’ s Manual 6 T roubleshooting No display: 1. Check DC po wer connections and DC polar ity with voltmeter . 2. Check fuse. No depth reading ( ## ## ## ## ## ) at all depths: 1. Check transducer for growth or multiple coats of paint. 2. Check the transducer cable for cuts and sharp bends. 3. Check that the transducer connection behind th ...

  • Standard Horizon DS41 - page 8

    DS41 Owner ’ s Manual 7 What comes with your Digital Depth Sounder Standard Mounting Bracket ................................................................. With mounting hardware Extension P ower Cord ......................... 6 feet long with quick-disconnect connectors T wist Lock F ace Plate ................................................. ...

  • Standard Horizon DS41 - page 9

    DS41 Owner ’ s Manual 8 2.75" 2.125" 13 ° Note: All transducers come with 30 feet of cable. Replacement Parts The follo wing par ts may be ordered from the P ar ts Depar tment. T o order , call T oll-free Number: 1-800-487-2788. Square F ace Plate ............................................................ Part Number 568001012A Round ...

  • Standard Horizon DS41 - page 10

    DS41 Owner ’ s Manual 9 Installation Face Plate Installation 1. T o install a face plate: a ) Attach the face plate to the front panel of the instrument. b ) T wist the face plate cloc kwise until tight. 2. T o remov e f ace plate, twist it anticlockwise until loose and detach. Instrument Installation The instrument can be easily installed in dif ...

  • Standard Horizon DS41 - page 11

    DS41 Owner ’ s Manual 10 6. Connect the power cord at the back of the instrument to a 12 V power supply which is active whenever the ignition switch is on. The red lead should be connected to the positive terminal of the power supply via a 1 amp fuse or a 1 amp circuit breaker . The black lead should be connected to the negative terminal. Figure ...

  • Standard Horizon DS41 - page 12

    DS41 Owner ’ s Manual 11 T ransducer Installation Note: The installation of a transducer is a job for a professional boat yard that performs numerous installations. The following is an informational guide- line on the installation of transducers. General Correct installation of the transducer is essential for optimum operation of the instrument. ...

  • Standard Horizon DS41 - page 13

    DS41 Owner ’ s Manual 12 Sailboats On sailboats, the transducer should be mounted where the acoustic beam will not be shaded by the keel. A spot forward of the keel is usually best. T ry to find an accessible spot with a minimum deadrise angle. See Figure 4. Powerboats On IO ’ s transducers mounted close to the engine usually yield good results ...

  • Standard Horizon DS41 - page 14

    DS41 Owner ’ s Manual 13 RUBBER GROMMET SEAL CAP OIL DEADRISE ANGLE CUT PVC PIPE TRANSDUCER Figure 7. In-Hull Installation In-Hull Installation T ransducer installation inside a solid fiberglass hull ma y degrade perf or mance of depth sounder. Therefore, this type of installation is not preferred over thru-hull and transom installations. Should ...

  • Standard Horizon DS41 - page 15

    DS41 Owner ’ s Manual 14 Multiple DS41 instruments can be installed on a single vessel. These instr uments can be connected together and configured to operate in a dual station configuration. One instrument is designated as a master and all other instruments, connected to it, are configured as slav es. The master device is connected to the depth ...

  • Standard Horizon DS41 - page 16

    DS41 Owner ’ s Manual 15 4. Continue to hold the # key until the display indicates the current linked/ separate selection. Linked Separate 5. Use the " and # keys to change the selection. 6. T o exit this mode , press and hold both the " and # k eys sim ultaneously . Alternatively , if no keys are pressed f or a period of 5 seconds norm ...

  • Standard Horizon DS41 - page 17

    DS41 Owner ’ s Manual 16 The DS41 can be configured to operate as a NMEA repeater . In this mode it will display depth information from any depth sounder outputing DPT or DBT NMEA depth data (no other NMEA depth sentences are supported). Notes: 1 ) The only information displayed from the DPT and DBT sentence is depth below the transducer . The us ...

Produzent Standard Horizon Kategorie SONAR

Dokumente, die wir vom Produzenten des Geräts Standard Horizon DS41 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Standard Horizon
- Bedienungsanleitungen DS41
- Produktkarten Standard Horizon
- Informationsbroschüren
- oder Energieetiketten Standard Horizon DS41
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Standard Horizon DS41.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Standard Horizon DS41, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Standard Horizon DS41. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Standard Horizon DS41 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Standard Horizon DS41, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Standard Horizon DS41 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Standard Horizon DS41 verständlich ist.

Eine gänzliche Bedienungsanleitung von Standard Horizon sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Standard Horizon DS41 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Standard Horizon DS41 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Standard Horizon DS41, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Standard Horizon DS41 - die uns die ersten Schritte während der Nutzung von Standard Horizon DS41 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Standard Horizon DS41 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Standard Horizon DS41 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Standard Horizon DS41?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Standard Horizon DS41 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Standard Horizon DS41 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)