English dropdown-ico

Manual Standard Horizon DS41

17 pages 0.32 mb
Download

Go to site of 17

Summary
  • Standard Horizon DS41 - page 1

    DS41 Digital Depth Sounder Owner’ s Manual Standard 2 Inch Installation Dual Station Operation NMEA Repeater Reads in Feet Fathoms or Meters Adjustable Prop or Surface Offset Shallow and Deep alarms Dual Station Operation ...

  • Standard Horizon DS41 - page 2

    DS41 Owner’s Manual DS41 Owner’s Manual DS41/HS/2G Contents Specifications ................................................................................................................. 2 Operation ...................................................................................................................... .. 3 Alarms .............. ...

  • Standard Horizon DS41 - page 3

    DS41 Owner’s Manual 2 Specifications • Size Mount 2" (51mm) diameter hole Depth behind face plate 3.75" (95mm) max. Display 3-character LCD • Color Black with texture on bezel. • Backlighting Red colored diffused lighting for displa y . • Water Integrity F ront will withstand direct water spra y . • Depth/Alarm Range 2.0 ! 600 ...

  • Standard Horizon DS41 - page 4

    DS41 Owner’s Manual 3 Operation Whenever power is applied the depth sounder is active and water depth is displayed. If the sonar signal does not show a bottom the display will indicate “- -”. This can occur if the water is aerated or the maximum depth is exceeded. Note: The maximum depth decreases as boat speed increases. Alarms T wo types of ...

  • Standard Horizon DS41 - page 5

    DS41 Owner ’ s Manual 4 Deep Alarm T o set the deep alar m: 1. Press the # ke y for three seconds. The display will show: dAL OFF OFF ON ^ V V 2. After two seconds the display will indicate the current Deep Alarm depth setting. 8 8 50 3. Use the " and # keys to change the value. If either key is held depressed for more than one second the re ...

  • Standard Horizon DS41 - page 6

    DS41 Owner ’ s Manual 5 4. Use the " and # keys to change the value. If either key is held depressed for more than one second the reading will increase or decrease rapidly . 5. The offset can be programmed in 0.1 unit steps from -9.9 ! 9.9 feet (or equivalent). When programmed f or a negative offset, ‘ - ’ will be indicated on the left h ...

  • Standard Horizon DS41 - page 7

    DS41 Owner ’ s Manual 6 T roubleshooting No display: 1. Check DC po wer connections and DC polar ity with voltmeter . 2. Check fuse. No depth reading ( ## ## ## ## ## ) at all depths: 1. Check transducer for growth or multiple coats of paint. 2. Check the transducer cable for cuts and sharp bends. 3. Check that the transducer connection behind th ...

  • Standard Horizon DS41 - page 8

    DS41 Owner ’ s Manual 7 What comes with your Digital Depth Sounder Standard Mounting Bracket ................................................................. With mounting hardware Extension P ower Cord ......................... 6 feet long with quick-disconnect connectors T wist Lock F ace Plate ................................................. ...

  • Standard Horizon DS41 - page 9

    DS41 Owner ’ s Manual 8 2.75" 2.125" 13 ° Note: All transducers come with 30 feet of cable. Replacement Parts The follo wing par ts may be ordered from the P ar ts Depar tment. T o order , call T oll-free Number: 1-800-487-2788. Square F ace Plate ............................................................ Part Number 568001012A Round ...

  • Standard Horizon DS41 - page 10

    DS41 Owner ’ s Manual 9 Installation Face Plate Installation 1. T o install a face plate: a ) Attach the face plate to the front panel of the instrument. b ) T wist the face plate cloc kwise until tight. 2. T o remov e f ace plate, twist it anticlockwise until loose and detach. Instrument Installation The instrument can be easily installed in dif ...

  • Standard Horizon DS41 - page 11

    DS41 Owner ’ s Manual 10 6. Connect the power cord at the back of the instrument to a 12 V power supply which is active whenever the ignition switch is on. The red lead should be connected to the positive terminal of the power supply via a 1 amp fuse or a 1 amp circuit breaker . The black lead should be connected to the negative terminal. Figure ...

  • Standard Horizon DS41 - page 12

    DS41 Owner ’ s Manual 11 T ransducer Installation Note: The installation of a transducer is a job for a professional boat yard that performs numerous installations. The following is an informational guide- line on the installation of transducers. General Correct installation of the transducer is essential for optimum operation of the instrument. ...

  • Standard Horizon DS41 - page 13

    DS41 Owner ’ s Manual 12 Sailboats On sailboats, the transducer should be mounted where the acoustic beam will not be shaded by the keel. A spot forward of the keel is usually best. T ry to find an accessible spot with a minimum deadrise angle. See Figure 4. Powerboats On IO ’ s transducers mounted close to the engine usually yield good results ...

  • Standard Horizon DS41 - page 14

    DS41 Owner ’ s Manual 13 RUBBER GROMMET SEAL CAP OIL DEADRISE ANGLE CUT PVC PIPE TRANSDUCER Figure 7. In-Hull Installation In-Hull Installation T ransducer installation inside a solid fiberglass hull ma y degrade perf or mance of depth sounder. Therefore, this type of installation is not preferred over thru-hull and transom installations. Should ...

  • Standard Horizon DS41 - page 15

    DS41 Owner ’ s Manual 14 Multiple DS41 instruments can be installed on a single vessel. These instr uments can be connected together and configured to operate in a dual station configuration. One instrument is designated as a master and all other instruments, connected to it, are configured as slav es. The master device is connected to the depth ...

  • Standard Horizon DS41 - page 16

    DS41 Owner ’ s Manual 15 4. Continue to hold the # key until the display indicates the current linked/ separate selection. Linked Separate 5. Use the " and # keys to change the selection. 6. T o exit this mode , press and hold both the " and # k eys sim ultaneously . Alternatively , if no keys are pressed f or a period of 5 seconds norm ...

  • Standard Horizon DS41 - page 17

    DS41 Owner ’ s Manual 16 The DS41 can be configured to operate as a NMEA repeater . In this mode it will display depth information from any depth sounder outputing DPT or DBT NMEA depth data (no other NMEA depth sentences are supported). Notes: 1 ) The only information displayed from the DPT and DBT sentence is depth below the transducer . The us ...

Manufacturer Standard Horizon Category SONAR

Documents that we receive from a manufacturer of a Standard Horizon DS41 can be divided into several groups. They are, among others:
- Standard Horizon technical drawings
- DS41 manuals
- Standard Horizon product data sheets
- information booklets
- or energy labels Standard Horizon DS41
All of them are important, but the most important information from the point of view of use of the device are in the user manual Standard Horizon DS41.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Standard Horizon DS41, service manual, brief instructions and user manuals Standard Horizon DS41. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Standard Horizon DS41.

Similar manuals

A complete manual for the device Standard Horizon DS41, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Standard Horizon DS41 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Standard Horizon DS41.

A complete Standard Horizon manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Standard Horizon DS41 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Standard Horizon DS41, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Standard Horizon DS41, that we can find in the current document
3. Tips how to use the basic functions of the device Standard Horizon DS41 - which should help us in our first steps of using Standard Horizon DS41
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Standard Horizon DS41
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Standard Horizon DS41 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Standard Horizon DS41?

Use the form below

If you did not solve your problem by using a manual Standard Horizon DS41, ask a question using the form below. If a user had a similar problem with Standard Horizon DS41 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)