Deutsch dropdown-ico

Bedienungsanleitung Bretford lap18eulba

33 Seiten 3.53 mb
Download

Zur Seite of 33

Summary
  • Bretford lap18eulba - page 1

    LAP18EULBA LAP18EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Q t y . Part No. Description 1 LAP18EULBA Car t Assembly , e-units at back LAP18EULFR Ca r t Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of ...

  • Bretford lap18eulba - page 2

    clip DET A I L 'A ' DET A I L 'B ' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford lap18eulba - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 16 screws (2 per shelf) from r ...

  • Bretford lap18eulba - page 4

    DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford lap18eulba - page 5

    Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back corner . 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlets face the interior a ...

  • Bretford lap18eulba - page 6

    Step 6 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 7 Reinstall 16 ...

  • Bretford lap18eulba - page 7

    Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and uncli ...

  • Bretford lap18eulba - page 9

    DET A I L 'D ' DET AI L 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside ...

  • Bretford lap18eulba - page 10

    Step 4 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'F Step 5 Reinstall 16 screws ...

  • Bretford lap18eulba - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlet s fa ...

  • Bretford lap18eulba - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AI L 'A'). DET A I L 'A' DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and u ...

  • Bretford lap18eulba - page 14

    DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left ...

  • Bretford lap18eulba - page 15

    Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should be visible from rear panel cutout. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned w ...

  • Bretford lap18eulba - page 16

    Step 5 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 6 Reinstall 16 ...

  • Bretford lap18eulba - page 17

    Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the side panel clips. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be re ...

  • Bretford lap18eulba - page 18

    clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. ...

  • Bretford lap18eulba - page 19

    Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in ...

  • Bretford lap18eulba - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) ...

  • Bretford lap18eulba - page 22

    Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/bracket Step 4 Remove 2 screws that secure timer to bracket. ...

  • Bretford lap18eulba - page 23

    Step 5 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout ...

  • Bretford lap18eulba - page 24

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET A I L 'C ' Step 8 Rein ...

  • Bretford lap18eulba - page 25

    TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power cord of the E-Units from the timer assembly (see Front View) and unclip the power cords from the side ...

  • Bretford lap18eulba - page 26

    clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the c ...

  • Bretford lap18eulba - page 27

    DET A I L 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B' mounting tab ...

  • Bretford lap18eulba - page 28

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b ...

  • Bretford lap18eulba - page 29

    Step 6 Remove 2 screws that secure timer to bracket. Step 7 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . ...

  • Bretford lap18eulba - page 30

    bottom flange- timer/bracket Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Car ...

  • Bretford lap18eulba - page 31

    DET A I L 'C ' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS. Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When reposition ...

  • Bretford lap18eulba - page 32

    E-Unit at rear         $8;  $8;           $8;   $8;            $8; $8; LABEL INST ALLA TION: E-Unit at front suggested label direction suggeste ...

  • Bretford lap18eulba - page 33

    Part #031-6565 Rev . 08.29.05 CH P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert reset tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e ...

Produzent Bretford Kategorie Indoor Furnishings

Dokumente, die wir vom Produzenten des Geräts Bretford lap18eulba erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Bretford
- Bedienungsanleitungen lap18eulba
- Produktkarten Bretford
- Informationsbroschüren
- oder Energieetiketten Bretford lap18eulba
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Bretford lap18eulba.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Bretford lap18eulba, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Bretford lap18eulba. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Bretford lap18eulba ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Bretford lap18eulba, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Bretford lap18eulba hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Bretford lap18eulba verständlich ist.

Eine gänzliche Bedienungsanleitung von Bretford sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Bretford lap18eulba bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Bretford lap18eulba befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Bretford lap18eulba, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Bretford lap18eulba - die uns die ersten Schritte während der Nutzung von Bretford lap18eulba erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Bretford lap18eulba hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Bretford lap18eulba im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Bretford lap18eulba?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Bretford lap18eulba nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Bretford lap18eulba hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Captcha
Neues Bild

Kommentare (0)