-
Bretford lap18eulba - page 1
LAP18EULBA LAP18EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Q t y . Part No. Description 1 LAP18EULBA Car t Assembly , e-units at back LAP18EULFR Ca r t Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of ...
-
Bretford lap18eulba - page 2
clip DET A I L 'A ' DET A I L 'B ' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly ...
-
Bretford lap18eulba - page 3
Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 16 screws (2 per shelf) from r ...
-
Bretford lap18eulba - page 4
DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...
-
Bretford lap18eulba - page 5
Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back corner . 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlets face the interior a ...
-
Bretford lap18eulba - page 6
Step 6 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 7 Reinstall 16 ...
-
Bretford lap18eulba - page 7
Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'B ' mounting tab ...
-
Bretford lap18eulba - page 8
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and uncli ...
-
Bretford lap18eulba - page 9
DET A I L 'D ' DET AI L 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside ...
-
Bretford lap18eulba - page 10
Step 4 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'F Step 5 Reinstall 16 screws ...
-
Bretford lap18eulba - page 11
Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlet s fa ...
-
Bretford lap18eulba - page 12
E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AI L 'A'). DET A I L 'A' DET A I L 'B ' mounting tab ...
-
Bretford lap18eulba - page 13
Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and u ...
-
Bretford lap18eulba - page 14
DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left ...
-
Bretford lap18eulba - page 15
Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should be visible from rear panel cutout. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned w ...
-
Bretford lap18eulba - page 16
Step 5 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 6 Reinstall 16 ...
-
Bretford lap18eulba - page 17
Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the side panel clips. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be re ...
-
Bretford lap18eulba - page 18
clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. ...
-
Bretford lap18eulba - page 19
Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in ...
-
Bretford lap18eulba - page 20
TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B ' mounting tab ...
-
Bretford lap18eulba - page 21
Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) ...
-
Bretford lap18eulba - page 22
Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/bracket Step 4 Remove 2 screws that secure timer to bracket. ...
-
Bretford lap18eulba - page 23
Step 5 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout ...
-
Bretford lap18eulba - page 24
Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET A I L 'C ' Step 8 Rein ...
-
Bretford lap18eulba - page 25
TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power cord of the E-Units from the timer assembly (see Front View) and unclip the power cords from the side ...
-
Bretford lap18eulba - page 26
clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the c ...
-
Bretford lap18eulba - page 27
DET A I L 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B' mounting tab ...
-
Bretford lap18eulba - page 28
Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b ...
-
Bretford lap18eulba - page 29
Step 6 Remove 2 screws that secure timer to bracket. Step 7 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . ...
-
Bretford lap18eulba - page 30
bottom flange- timer/bracket Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Car ...
-
Bretford lap18eulba - page 31
DET A I L 'C ' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS. Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When reposition ...
-
Bretford lap18eulba - page 32
E-Unit at rear $8; $8; $8; $8; $8; $8; LABEL INST ALLA TION: E-Unit at front suggested label direction suggeste ...
-
Bretford lap18eulba - page 33
Part #031-6565 Rev . 08.29.05 CH P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert reset tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e ...
Avez-vous une question à propos de Bretford lap18eulba?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Bretford lap18eulba, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Bretford lap18eulba il est probable qu’il a envie de partager la façon de le résoudre.