Русский dropdown-ico

Инструкция обслуживания Bretford lap18eulba

33 страниц 3.53 mb
Скачать

Перейти на страницу of 33

Summary
  • Bretford lap18eulba - page 1

    LAP18EULBA LAP18EULFR NOTEBOOK CART ASSEMBL Y WITH TIMER Assembly Instructions for: INTERIOR E-UNIT REPOSITIONING / REPLACEMENT AND TIMER REPLACEMENT Parts List Q t y . Part No. Description 1 LAP18EULBA Car t Assembly , e-units at back LAP18EULFR Ca r t Assembly , e-units at front T ools Required Philips screwdriver Step 1 Open both front doors of ...

  • Bretford lap18eulba - page 2

    clip DET A I L 'A ' DET A I L 'B ' E-Unit power cord timer assembly bottom shelf Front View bracket assembly bracket assembly ...

  • Bretford lap18eulba - page 3

    Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Step 3 Remove 16 screws (2 per shelf) from r ...

  • Bretford lap18eulba - page 4

    DET A I L 'D ' Step 4 Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D', then carefully sliding out. Set each shelf aside. mounting tab ...

  • Bretford lap18eulba - page 5

    Step 5 Reinstall the E-Units (set aside from being removed from the front) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. T ilt in and set bottom in back corner . 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlets face the interior a ...

  • Bretford lap18eulba - page 6

    Step 6 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 7 Reinstall 16 ...

  • Bretford lap18eulba - page 7

    Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AIL 'A'). DET A I L 'A ' E-UNIT REPOSITIONING: 'REAR TO FRONT' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 8

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) and uncli ...

  • Bretford lap18eulba - page 9

    DET A I L 'D ' DET AI L 'E' Step 3 Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. Remove rear-right E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside ...

  • Bretford lap18eulba - page 10

    Step 4 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'F Step 5 Reinstall 16 screws ...

  • Bretford lap18eulba - page 11

    Step 6 Reinstall the E-Units (set aside from being removed from the rear) as follows: 1. Rotate the E-Unit 180 degrees (from original position). 2. Cross over to opposite corner of cart. 3. Tilt in and set against offset of bottom panel (of cart). 4. Grip the top and tilt to the upright position. When repositioned correctly , the E-Unit outlet s fa ...

  • Bretford lap18eulba - page 12

    E-UNIT REPLACEMENT : 'REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Remove 16 screws (2 per shelf) from rear panel that secure the 8 interior shelves (see DET AI L 'A'). DET A I L 'A' DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 13

    Step 2 With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cord(s) of the E-Unit(s) from the timer assembly (see Front View) and u ...

  • Bretford lap18eulba - page 14

    DET A I L 'C ' DET A I L 'D ' Step 3 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf bracket and set it aside. rear-right rear-left ...

  • Bretford lap18eulba - page 15

    Step 4 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should be visible from rear panel cutout. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned w ...

  • Bretford lap18eulba - page 16

    Step 5 Reinstall the 8 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in all remaining shelves into position as the bottom shelf. DET A I L 'E' Step 6 Reinstall 16 ...

  • Bretford lap18eulba - page 17

    Step 1 Open both front doors of cart to access E-Unit(s). From underneath the bottom shelf, carefully unplug the power cord of the E-Unit(s) from the timer assembly (see Front View) and unclip the power cord(s) from the side panel clips. Loosen the screw holding the E-Unit bracket assembly and remove (2) bracket assemblies of the E-Unit(s) to be re ...

  • Bretford lap18eulba - page 18

    clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. ...

  • Bretford lap18eulba - page 19

    Step 3 Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting it in sideways to the top. When repositioned correctly , the E-Unit(s) outlets face the interior and power switch should face the front. Reinstall the E-Unit bracket assemblies (make sure that the top flange of the E-unit is aligned with the slot in ...

  • Bretford lap18eulba - page 20

    TIMER REPLACEMENT : 'E-UNIT A T REAR LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING DET A I L 'A ' Step 1 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B ' mounting tab ...

  • Bretford lap18eulba - page 21

    Step 2 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. E-Unit power cord timer assembly Front View clip Carefully unplug the power cords of the E-Units from the timer assembly (see Front View) ...

  • Bretford lap18eulba - page 22

    Step 3 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/bracket Step 4 Remove 2 screws that secure timer to bracket. ...

  • Bretford lap18eulba - page 23

    Step 5 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . Step 6 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout ...

  • Bretford lap18eulba - page 24

    Step 7 Reinstall the 3 interior shelves as follows: 1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracket tab). (M a k e sure that the shelf flanges are ALL seated into the mounting tabs.) 2. Slide in remaining 2 shelves into position as the bottom shelf. notch tab DET A I L 'C ' Step 8 Rein ...

  • Bretford lap18eulba - page 25

    TIMER REPLACEMENT : 'E-UNIT A T FRONT LOCA TION' NOTE: UNPLUG CART (TIMER) POWER CORD FROM POWER SOURCE BEFORE ST AR TING Step 1 Open both front doors of cart to access E-Units. From underneath the bottom shelf, carefully unplug the power cord of the E-Units from the timer assembly (see Front View) and unclip the power cords from the side ...

  • Bretford lap18eulba - page 26

    clip DET A I L 'A ' DET A I L 'B ' bracket assembly bracket assembly Step 2 Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interior shelf channel and set it aside. Remove front-right E-Unit by griping the top and tilt it side ways until it clears the underside of the c ...

  • Bretford lap18eulba - page 27

    DET A I L 'A' Step 3 Remove 6 screws (2 per shelf) from rear panel that secure the 3 bottom interior shelves (see DET AI L 'A'). DET A I L 'B' mounting tab ...

  • Bretford lap18eulba - page 28

    Step 4 With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'B', then carefully sliding out. Set each shelf aside. Step 5 Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove timer/bracket assembly . bottom flange- timer/b ...

  • Bretford lap18eulba - page 29

    Step 6 Remove 2 screws that secure timer to bracket. Step 7 Inst all replacement timer with 2 screws. Adjust timer dial to current time. If necessary , adjust timer charging times to match the original timer . ...

  • Bretford lap18eulba - page 30

    bottom flange- timer/bracket Step 8 Install replacement timer/bracket assembly onto bottom, rear of cart with 2 screws. Feed the power cord from the timer out the grommeted hole (with cord wrap bracket located above cutout). Make sure timer face is aligned with rear panel cutouts. notch tab Step 9 Reinstall the 3 interior shelves as follows: 1. Car ...

  • Bretford lap18eulba - page 31

    DET A I L 'C ' Step 10 Reinstall 6 screws to rear panel that will secure the 3 interior shelves (see DET AIL 'C'). DO NOT OVER TIGHTEN SCREWS. Step 1 1 Carefully reinstall E-Units into position by placing bottom in first and tilting it in sideways to the top (underneath the channel bracket of the cart top panel). When reposition ...

  • Bretford lap18eulba - page 32

    E-Unit at rear         $8;  $8;           $8;   $8;            $8; $8; LABEL INST ALLA TION: E-Unit at front suggested label direction suggeste ...

  • Bretford lap18eulba - page 33

    Part #031-6565 Rev . 08.29.05 CH P AD LOCK - DOOR: Open Lock The First T ime 1) Set the combination to 0-0-0-0 2) Depress shackle and pull open. T o Set Y ou Own Combination **REMEMBER: Combination can only be set when lock is open. 1) Insert reset tool (included in package) in hole on side of lock. 2) Push key in and turn key 90 degrees in e ...

Производитель Bretford Категория Indoor Furnishings

Документы, которые мы получаем от производителя устройства Bretford lap18eulba мы можем разделить на несколько групп. Это в частности:
- технические чертежи Bretford
- инструкции обслуживания lap18eulba
- паспорта изделия Bretford
- информационные брошюры
- энергетические этикетки Bretford lap18eulba
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Bretford lap18eulba.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Bretford lap18eulba, инструкции обслуживания, короткие инструкции или инструкции пользователя Bretford lap18eulba. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Bretford lap18eulba.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Bretford lap18eulba, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Bretford lap18eulba пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Bretford lap18eulba.

Полная инструкция обслуживания Bretford, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Bretford lap18eulba - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Bretford lap18eulba, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Bretford lap18eulba, которое найдем в данном документе
3. Советы по использованию основных функций устройства Bretford lap18eulba - которые должны облегчить нам первые шаги во время использования Bretford lap18eulba
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Bretford lap18eulba
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Bretford lap18eulba в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Bretford lap18eulba?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Bretford lap18eulba, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Bretford lap18eulba со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)