Bedienungsanleitung Clarion APX1000.2

16 Seiten 0.28 mb
Download

Zur Seite of 16

Summary
  • Clarion APX1000.2 - page 1

    ...

  • Clarion APX1000.2 - page 2

    INTRODUCTION The Clarion APX1000.2 is a full-featured two-channel amplifier incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, including those with satellite speaker ...

  • Clarion APX1000.2 - page 3

    DESCRIPTION The Clarion APX1000.2 two-channel amplifier provides 2x270 watts of power into a 4 ohm load and 2x525 watts of power into a 2 ohm load. This full featured model is an excellent choice for a variety of car audio sound system configurations. The APX1000.2 uses an unregulated MOSFET power supply for superior control of output wattage. A to ...

  • Clarion APX1000.2 - page 4

    • Gain Control - This allows you to set the nominal operating level of the amplifier . The amplifier ’ s range, 250mV to 2.5V for RCA inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high-Q” (i.e. narrow frequency band) Bass Boost circuit. It acts much like ...

  • Clarion APX1000.2 - page 5

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX1000.2 contains power and speaker connections as shown below . 5 1. Power Save Selector Switch 2. Left Speaker Output 3. Right Speaker Output 4. Ground Input 5. Remote Turn-on Input 6. Battery + 12v Input Figure 2- ...

  • Clarion APX1000.2 - page 6

    APPLICA TIONS The Clarion APX1000.2 2-channel car audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Set X-Over Mode to LP and adjust FREQ to speak ...

  • Clarion APX1000.2 - page 7

    2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or sa ...

  • Clarion APX1000.2 - page 8

    Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 318 265 199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a ...

  • Clarion APX1000.2 - page 9

    INSTALLA TION This section lists Mounting and W iring Precautions for installing a Clarion APX1000.2. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your authorized ...

  • Clarion APX1000.2 - page 10

    5. Add an external fuse on the amplifier’ s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire ...

  • Clarion APX1000.2 - page 11

    11 Figure 6. - Electrical connections for the APX1000.2 ...

  • Clarion APX1000.2 - page 12

    SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. T urn the Gain Control all the way counter-clockwise. 2. T urn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all T one or Equalizati ...

  • Clarion APX1000.2 - page 13

    FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay , slowly increase the V olume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to T roubleshooting. Depending on your system design, the levels may become quite loud even a ...

  • Clarion APX1000.2 - page 14

    14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to e ...

  • Clarion APX1000.2 - page 15

    NOTES 15 ...

  • Clarion APX1000.2 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX1000.0-10 Rev .1 (04/00) ...

Produzent Clarion Kategorie Stereo Amplifier

Dokumente, die wir vom Produzenten des Geräts Clarion APX1000.2 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Clarion
- Bedienungsanleitungen APX1000.2
- Produktkarten Clarion
- Informationsbroschüren
- oder Energieetiketten Clarion APX1000.2
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Clarion APX1000.2.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Clarion APX1000.2, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Clarion APX1000.2. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Clarion APX1000.2 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Clarion APX1000.2, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Clarion APX1000.2 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Clarion APX1000.2 verständlich ist.

Eine gänzliche Bedienungsanleitung von Clarion sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Clarion APX1000.2 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Clarion APX1000.2 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Clarion APX1000.2, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Clarion APX1000.2 - die uns die ersten Schritte während der Nutzung von Clarion APX1000.2 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Clarion APX1000.2 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Clarion APX1000.2 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Clarion APX1000.2?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Clarion APX1000.2 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Clarion APX1000.2 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)