Manuale per l’uso Clarion APX1000.2

16 pagine 0.28 mb
Scarica

Vai alla pagina of 16

Summary
  • Clarion APX1000.2 - page 1

    ...

  • Clarion APX1000.2 - page 2

    INTRODUCTION The Clarion APX1000.2 is a full-featured two-channel amplifier incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, including those with satellite speaker ...

  • Clarion APX1000.2 - page 3

    DESCRIPTION The Clarion APX1000.2 two-channel amplifier provides 2x270 watts of power into a 4 ohm load and 2x525 watts of power into a 2 ohm load. This full featured model is an excellent choice for a variety of car audio sound system configurations. The APX1000.2 uses an unregulated MOSFET power supply for superior control of output wattage. A to ...

  • Clarion APX1000.2 - page 4

    • Gain Control - This allows you to set the nominal operating level of the amplifier . The amplifier ’ s range, 250mV to 2.5V for RCA inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high-Q” (i.e. narrow frequency band) Bass Boost circuit. It acts much like ...

  • Clarion APX1000.2 - page 5

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX1000.2 contains power and speaker connections as shown below . 5 1. Power Save Selector Switch 2. Left Speaker Output 3. Right Speaker Output 4. Ground Input 5. Remote Turn-on Input 6. Battery + 12v Input Figure 2- ...

  • Clarion APX1000.2 - page 6

    APPLICA TIONS The Clarion APX1000.2 2-channel car audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Set X-Over Mode to LP and adjust FREQ to speak ...

  • Clarion APX1000.2 - page 7

    2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or sa ...

  • Clarion APX1000.2 - page 8

    Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 318 265 199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a ...

  • Clarion APX1000.2 - page 9

    INSTALLA TION This section lists Mounting and W iring Precautions for installing a Clarion APX1000.2. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your authorized ...

  • Clarion APX1000.2 - page 10

    5. Add an external fuse on the amplifier’ s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire ...

  • Clarion APX1000.2 - page 11

    11 Figure 6. - Electrical connections for the APX1000.2 ...

  • Clarion APX1000.2 - page 12

    SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. T urn the Gain Control all the way counter-clockwise. 2. T urn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all T one or Equalizati ...

  • Clarion APX1000.2 - page 13

    FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay , slowly increase the V olume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to T roubleshooting. Depending on your system design, the levels may become quite loud even a ...

  • Clarion APX1000.2 - page 14

    14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to e ...

  • Clarion APX1000.2 - page 15

    NOTES 15 ...

  • Clarion APX1000.2 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX1000.0-10 Rev .1 (04/00) ...

Fabbricante Clarion Categoria Stereo Amplifier

I documenti che otteniamo dal fabbricante del dispositivoClarion APX1000.2 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Clarion
- manuali per l’uso APX1000.2
- schede prodotto Clarion
- opuscoli
- o etichette energetiche Clarion APX1000.2
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Clarion APX1000.2.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Clarion APX1000.2, manuali di manutenzione, brevi manuali o manuali utente Clarion APX1000.2. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Clarion APX1000.2.

Manuali per l’uso simili

Manuale completo del dispositivo Clarion APX1000.2, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Clarion APX1000.2 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Clarion APX1000.2.

Il manuale per l’uso completo Clarion, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Clarion APX1000.2 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Clarion APX1000.2, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Clarion APX1000.2 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Clarion APX1000.2 - che ci dovrebbe aiutare nei primi passi durante l'uso Clarion APX1000.2
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Clarion APX1000.2
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Clarion APX1000.2 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Clarion APX1000.2?

Utilizza il modulo sottostante

Se non hai risolto il problema con Clarion APX1000.2 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Clarion APX1000.2 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)