Manuale per l’uso Clarion APX200

16 pagine 0.25 mb
Scarica

Vai alla pagina of 16

Summary
  • Clarion APX200 - page 1

    OPERATIONAL INSTALLATION MANUAL ...

  • Clarion APX200 - page 2

    APX200.2M Power System Amplifier INTRODUCTION The Clarion APX200.2M is a full-featured two-channel amplifier incorporating the following features: • Full frequency response with low distortion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, inclu ...

  • Clarion APX200 - page 3

    OWNER’S MANUAL 1 DESCRIPTION The Clarion APX200.2M two-channel amplifier provides 2x70 watts of power into a 4 ohm load and 2x110 watts of power into a 2 ohm load. This full featured model is an excellent choice for a variety of marine audio sound system configurations. The APX200.2M uses an unregulated MOSFET power supply for superior control of ...

  • Clarion APX200 - page 4

    APX200.2M Power System Amplifier 2 • Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier's range, 250mV to 2.5V for RCA inputs or 500mV to 5V for speaker level inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Contro l- The amplifier also features a &quo ...

  • Clarion APX200 - page 5

    OWNER’S MANUAL 3 CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2M contains power and speaker connections as shown below. Figure 2 1. Left Speaker Output 2. Right Speaker Output 3. Remote Turn-on Input 4. Ground Input 5. Battery + 12V Input 6. 25 Amp Fuse ...

  • Clarion APX200 - page 6

    APX200.2M Power System Amplifier 4 APPLICATIONS The Clarion APX200.2M 2-channel marine audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged - Mono Subwoofer System Set X-Over Mode to LP and adjust FREQ to speaker specifications. Figure 3 - In this application the amplifi ...

  • Clarion APX200 - page 7

    OWNER’S MANUAL 5 2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or satellite or subwoofer) speakers. NOTE: A passive crossover must be used with satellite speakers. Set X-Over Mode as shown. Set X-Over Mode a ...

  • Clarion APX200 - page 8

    APX200.2M Power System Amplifier 6 Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) Subwoofer 4 Ohms NOTE: Chart values based on 4 Ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a 6dB per octave crossover at specified frequencies. Use co ...

  • Clarion APX200 - page 9

    OWNER’S MANUAL 7 INSTALLATION This section lists Mounting and Wiring Precautions for installing a Clarion APX200.2M marine amplifier. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yours ...

  • Clarion APX200 - page 10

    APX200.2M Power System Amplifier 8 5. Add an external fuse on the amplifier's positive (+) power lead and connect it as close as possible to the vessel's (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external f use will protect the electrical system f ...

  • Clarion APX200 - page 11

    OWNER’S MANUAL 9 Figure 6 - Electrical connections for the APX200.2M ...

  • Clarion APX200 - page 12

    APX200.2M Power System Amplifier 10 SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. Turn the Gain Control all the way counter-clockwise. 2. Turn the vessel's Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON p ...

  • Clarion APX200 - page 13

    OWNER’S MANUAL 11 FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay, slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may become ...

  • Clarion APX200 - page 14

    APX200.2M Power System Amplifier 12 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check pola ...

  • Clarion APX200 - page 15

    OWNER’S MANUAL 13 NOTES ...

  • Clarion APX200 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX200.2M-10 Rev.1 (03/01) ...

Fabbricante Clarion Categoria Stereo Amplifier

I documenti che otteniamo dal fabbricante del dispositivoClarion APX200 possono essere suddivisi in diversi gruppi. Questi sono tra gli altri:
- disegni tecnici Clarion
- manuali per l’uso APX200
- schede prodotto Clarion
- opuscoli
- o etichette energetiche Clarion APX200
Tutti sono importanti, ma le informazioni più importanti dal punto di vista di utilizzo del dispositivo possono essere trovate nel manuale per l’uso Clarion APX200.

Un gruppo di documenti denominato manuali per l’uso, è anche suddiviso in tipi più specifici, come: Manuali di installazione Clarion APX200, manuali di manutenzione, brevi manuali o manuali utente Clarion APX200. A seconda delle esigenze, si dovrebbe cercare il documento necessario. Nel nostro sito web, puoi visualizzare il manuale più popolare per l'uso del prodotto Clarion APX200.

Manuali per l’uso simili

Manuale completo del dispositivo Clarion APX200, come deve essere?
Il manuale per l’uso, denominato anche istruzioni per l’uso, o semplicemente il manuale è un documento tecnico progettato per aiutare ad utilizzare Clarion APX200 dagli utenti. I manuali sono di solito scritti da uno scrittore tecnico, ma in un linguaggio accessibile a tutti gli utenti Clarion APX200.

Il manuale per l’uso completo Clarion, dovrebbe includere vari elementi di base. Alcuni di loro sono meno importanti, come ad esempio: copertina / pagina del titolo o pagina di autore. Tuttavia, la parte rimanente, dovrebbe fornire informazioni importanti dal punto di vista dell'utente.

1. Introduzione e la guida su come utilizzare il manuale Clarion APX200 - All'inizio di ogni manuale, dovremmo trovare indizi su come utilizzare il documento. Dovrebbe contenere informazioni sulla posizione dell’indice Clarion APX200, FAQ o i problemi più comuni : i punti che sono più spesso cercati dagli utenti di ogni manuale
2. Indice - elenco di tutti i suggerimenti per Clarion APX200 che possono essere trovati nel documento corrente
3. Suggerimenti su come utilizzare le funzioni di base del dispositivo Clarion APX200 - che ci dovrebbe aiutare nei primi passi durante l'uso Clarion APX200
4. Troubleshooting - sequenza sistematica delle attività che vi aiuterà a diagnosticare e, successivamente, risolvere i problemi più importanti del Clarion APX200
5. FAQ - domande più frequenti
6. Dettagli di contatto Informazioni su dove cercare il contatto con il fabbricante / servizio Clarion APX200 in un dato paese, se il problema non può essere risolto da noi stessi.

Hai una domanda su Clarion APX200?

Utilizza il modulo sottostante

Se non hai risolto il problema con Clarion APX200 con l'aiuto del manuale che hai trovato, fai una domanda utilizzando il modulo sottostante. Se un utente ha avuto un problema simile con Clarion APX200 è probabile che voglia condividere il modo di risolverlo.

Riscrivi il testo dall’immagine

Commenti (0)