English dropdown-ico

Manual Clarion APX1000.2

16 pages 0.28 mb
Download

Go to site of 16

Summary
  • Clarion APX1000.2 - page 1

    ...

  • Clarion APX1000.2 - page 2

    INTRODUCTION The Clarion APX1000.2 is a full-featured two-channel amplifier incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use in various systems, including those with satellite speaker ...

  • Clarion APX1000.2 - page 3

    DESCRIPTION The Clarion APX1000.2 two-channel amplifier provides 2x270 watts of power into a 4 ohm load and 2x525 watts of power into a 2 ohm load. This full featured model is an excellent choice for a variety of car audio sound system configurations. The APX1000.2 uses an unregulated MOSFET power supply for superior control of output wattage. A to ...

  • Clarion APX1000.2 - page 4

    • Gain Control - This allows you to set the nominal operating level of the amplifier . The amplifier ’ s range, 250mV to 2.5V for RCA inputs, can accommodate input levels from virtually any brand of source unit. • Bass Boost Control - The amplifier also features a “high-Q” (i.e. narrow frequency band) Bass Boost circuit. It acts much like ...

  • Clarion APX1000.2 - page 5

    CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX1000.2 contains power and speaker connections as shown below . 5 1. Power Save Selector Switch 2. Left Speaker Output 3. Right Speaker Output 4. Ground Input 5. Remote Turn-on Input 6. Battery + 12v Input Figure 2- ...

  • Clarion APX1000.2 - page 6

    APPLICA TIONS The Clarion APX1000.2 2-channel car audio amplifier can be used in a variety of system applications. Here are some examples to help plan your own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive a subwoofer. Set X-Over Mode to LP and adjust FREQ to speak ...

  • Clarion APX1000.2 - page 7

    2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier is used in stereo and drives two full-range (or sa ...

  • Clarion APX1000.2 - page 8

    Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100 125 150 200 L (mH) 8.0 6.4 5.1 4.2 3.2 C (uF) 497 398 318 265 199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table provides component values to create a ...

  • Clarion APX1000.2 - page 9

    INSTALLA TION This section lists Mounting and W iring Precautions for installing a Clarion APX1000.2. Combined with the experience of a professional installer, these safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, do not install the amplifier yourself. Instead, see your authorized ...

  • Clarion APX1000.2 - page 10

    5. Add an external fuse on the amplifier’ s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire ...

  • Clarion APX1000.2 - page 11

    11 Figure 6. - Electrical connections for the APX1000.2 ...

  • Clarion APX1000.2 - page 12

    SETTING THE GAIN After completing the installation, follow these steps to set the Gain Control and then perform the Final System Checks. 1. T urn the Gain Control all the way counter-clockwise. 2. T urn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all T one or Equalizati ...

  • Clarion APX1000.2 - page 13

    FINAL SYSTEM CHECKS 1. Start the engine and turn on the source unit. After a two-second delay , slowly increase the V olume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to T roubleshooting. Depending on your system design, the levels may become quite loud even a ...

  • Clarion APX1000.2 - page 14

    14 Problem Distorted audio. Solution Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.) Problem Audio lacks punch. Solution Speakers wired incorrectly, which causes cancellation of bass frequencies. Check polarity of wires from amplifier to e ...

  • Clarion APX1000.2 - page 15

    NOTES 15 ...

  • Clarion APX1000.2 - page 16

    661 W. Redondo Beach Blvd. Gardena, CA 90247 1-800-GO-CLARION www.clarion-usa.com APX1000.0-10 Rev .1 (04/00) ...

Manufacturer Clarion Category Stereo Amplifier

Documents that we receive from a manufacturer of a Clarion APX1000.2 can be divided into several groups. They are, among others:
- Clarion technical drawings
- APX1000.2 manuals
- Clarion product data sheets
- information booklets
- or energy labels Clarion APX1000.2
All of them are important, but the most important information from the point of view of use of the device are in the user manual Clarion APX1000.2.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Clarion APX1000.2, service manual, brief instructions and user manuals Clarion APX1000.2. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Clarion APX1000.2.

Similar manuals

A complete manual for the device Clarion APX1000.2, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Clarion APX1000.2 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Clarion APX1000.2.

A complete Clarion manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Clarion APX1000.2 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Clarion APX1000.2, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Clarion APX1000.2, that we can find in the current document
3. Tips how to use the basic functions of the device Clarion APX1000.2 - which should help us in our first steps of using Clarion APX1000.2
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Clarion APX1000.2
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Clarion APX1000.2 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Clarion APX1000.2?

Use the form below

If you did not solve your problem by using a manual Clarion APX1000.2, ask a question using the form below. If a user had a similar problem with Clarion APX1000.2 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)