Bedienungsanleitung Eaton TRS 3064

13 Seiten 1.4 mb
Download

Zur Seite of 13

Summary
  • Eaton TRS 3064 - page 1

    TRS 3064 Installation, Operation and Maintenance of the Airflex@ Timing Rotorseal and Cam Limit Switch Revised: Feb. 1, 1982 ...

  • Eaton TRS 3064 - page 2

    1.0 Operation Throughout this manual, there are a number of Hazard Warnings that must be read and understood in order to prevent possible personal injury and/or damage to the equipment. Carefully read these warn- ings. They are included to protect you! 1.1 Description: This manual describes two Airflex@ timing control devices, namely, the Airflex@ ...

  • Eaton TRS 3064 - page 3

    Figure 1 illustrates the cams assembled in the timing section of both devices and their relationships. 1 Cam No. 2 Cam Insert No. 3 Cam No. 4 Cam insert No. Cams for Clockwise Rotation Cams for Counterclockwise Rotation Figure 1. Cam profiles and their relationships 3 ...

  • Eaton TRS 3064 - page 4

    Cam No. 3 (28 and 28A) monitors the effective- ness of the press braking system at the top of the stroke. When cam No. 3 is positioned according to Paragraph 2.3, deviations in stopping position greater than + 15” from top dead center will be detected. 2.0 Installation n ! Danger: Prior to installation of the Airflex’“’ Timing Rotorseal and ...

  • Eaton TRS 3064 - page 5

    2.1.2. To a) b) c) d) e) f) g) h) i) j) mount the timing rotorseal: Make sure that the air tube “O” rings (2) are in place. Install the plastic insert (37A) in the head of the drive screw (37). Install drive screw. Tighten the screw, being careful not to distort the end plate (36). Tie-wire the drive screw to the end plate mounting screws. Alig ...

  • Eaton TRS 3064 - page 6

    Before mounting the timer, check to be sure its direction of rotation corresponds to that of the shaft. Fasten the flange to the shaft with lockwashers and cap screws. Refer to appropriate paragraph and mount second timer. W iring instructions are given in Paragraph 2.2. 2.2 Wiring: Two rotary timers are required in the Airflex@ press control syste ...

  • Eaton TRS 3064 - page 7

    m) Retighten the jam nuts (30) and repeat Steps “f”, “g” and “h”. n) Repeat this procedure as necessary to ob- tain the desired stopping position. 2.3.2 Long Operation: This feature is provided so an adjustment can be made to extend the LS4 open time and accommodate presses with long strokes and/or slow crankshaft speeds. a) b) c) d) e) ...

  • Eaton TRS 3064 - page 8

    Breaker Point Opening Gap: This gap is preset at the factory on new units at time of assembly. A gap setting of .040” to .050” must be maintained at all times. The opening gap must be checked regularly and reset when required. To inspect for proper opening gap: a) b) c) d) e) h) i) j) k) Position the crankshaft at top dead center. Use die safet ...

  • Eaton TRS 3064 - page 9

    o) P) q) r) s) t) u) v) w) Align No. 5 cam with previously establish- ed top stop mark by rotating cam adjusting knob. Maintain No. 5 cam alignment by holding adjusting knob. Rotate No. 3 cam so that indicator groove lines up with the fiber cam follower on LS3 breaker point. Refer to Figure 4. This alignment must be done with the crankshaft at top ...

  • Eaton TRS 3064 - page 10

    ...

  • Eaton TRS 3064 - page 11

    Item No. - 6. 20. 22. 23. 24. 25. 26. 27. 28. 28A 29. 30. 31. 32. 33. 33A 34 38. 40. 41. 42. 45. 46. 47. Part No. Description 302276 159 x 41 139 x 12 See table C See table C 201854 See table C 201869 See table C 306030 203003 61 x 22 412230 409346 See table C See table C 119 x 23 507137 153 x 530 203107 404583 411367 405330 203351 Shaft Bearing Sn ...

  • Eaton TRS 3064 - page 12

    FOOT MOUNTED CAM LIMIT SWITCH Part No. for Optional Cam No. 3 (Item No. 28A), is as follows: 203002 (For clockwise and clockwise 30” dwell) 203087 (for c’clockwise and c’clockwise 30” dwell) Eaton Corporation Airflex Division Cleveland, Ohio 44144 PWNTED IN u. 5. A. ...

  • Eaton TRS 3064 - page 13

    PDF form at Form ML-31 8 Revised September 3, 1997 Eaton Cor poration Airflex Division 9919 Clinton Road Cleveland, Ohio 44144 Printed in U.S.A. EAT ON PROD UCT WARR ANTY Subject to t he c ondit io ns st ated herei n, Eaton C orpo rati on w arran ts to the Pur chaser that e ach ne w Air fl ex Produ ct manufa ctured by Eaton will be free from fai lu ...

Produzent Eaton Kategorie Switch

Dokumente, die wir vom Produzenten des Geräts Eaton TRS 3064 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Eaton
- Bedienungsanleitungen TRS 3064
- Produktkarten Eaton
- Informationsbroschüren
- oder Energieetiketten Eaton TRS 3064
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Eaton TRS 3064.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Eaton TRS 3064, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Eaton TRS 3064. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Eaton TRS 3064 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Eaton TRS 3064, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Eaton TRS 3064 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Eaton TRS 3064 verständlich ist.

Eine gänzliche Bedienungsanleitung von Eaton sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Eaton TRS 3064 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Eaton TRS 3064 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Eaton TRS 3064, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Eaton TRS 3064 - die uns die ersten Schritte während der Nutzung von Eaton TRS 3064 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Eaton TRS 3064 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Eaton TRS 3064 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Eaton TRS 3064?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Eaton TRS 3064 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Eaton TRS 3064 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)