Eaton TRS 3064の取扱説明書

13ページ 1.4 mb
ダウンロード

ページに移動 of 13

Summary
  • Eaton TRS 3064 - page 1

    TRS 3064 Installation, Operation and Maintenance of the Airflex@ Timing Rotorseal and Cam Limit Switch Revised: Feb. 1, 1982 ...

  • Eaton TRS 3064 - page 2

    1.0 Operation Throughout this manual, there are a number of Hazard Warnings that must be read and understood in order to prevent possible personal injury and/or damage to the equipment. Carefully read these warn- ings. They are included to protect you! 1.1 Description: This manual describes two Airflex@ timing control devices, namely, the Airflex@ ...

  • Eaton TRS 3064 - page 3

    Figure 1 illustrates the cams assembled in the timing section of both devices and their relationships. 1 Cam No. 2 Cam Insert No. 3 Cam No. 4 Cam insert No. Cams for Clockwise Rotation Cams for Counterclockwise Rotation Figure 1. Cam profiles and their relationships 3 ...

  • Eaton TRS 3064 - page 4

    Cam No. 3 (28 and 28A) monitors the effective- ness of the press braking system at the top of the stroke. When cam No. 3 is positioned according to Paragraph 2.3, deviations in stopping position greater than + 15” from top dead center will be detected. 2.0 Installation n ! Danger: Prior to installation of the Airflex’“’ Timing Rotorseal and ...

  • Eaton TRS 3064 - page 5

    2.1.2. To a) b) c) d) e) f) g) h) i) j) mount the timing rotorseal: Make sure that the air tube “O” rings (2) are in place. Install the plastic insert (37A) in the head of the drive screw (37). Install drive screw. Tighten the screw, being careful not to distort the end plate (36). Tie-wire the drive screw to the end plate mounting screws. Alig ...

  • Eaton TRS 3064 - page 6

    Before mounting the timer, check to be sure its direction of rotation corresponds to that of the shaft. Fasten the flange to the shaft with lockwashers and cap screws. Refer to appropriate paragraph and mount second timer. W iring instructions are given in Paragraph 2.2. 2.2 Wiring: Two rotary timers are required in the Airflex@ press control syste ...

  • Eaton TRS 3064 - page 7

    m) Retighten the jam nuts (30) and repeat Steps “f”, “g” and “h”. n) Repeat this procedure as necessary to ob- tain the desired stopping position. 2.3.2 Long Operation: This feature is provided so an adjustment can be made to extend the LS4 open time and accommodate presses with long strokes and/or slow crankshaft speeds. a) b) c) d) e) ...

  • Eaton TRS 3064 - page 8

    Breaker Point Opening Gap: This gap is preset at the factory on new units at time of assembly. A gap setting of .040” to .050” must be maintained at all times. The opening gap must be checked regularly and reset when required. To inspect for proper opening gap: a) b) c) d) e) h) i) j) k) Position the crankshaft at top dead center. Use die safet ...

  • Eaton TRS 3064 - page 9

    o) P) q) r) s) t) u) v) w) Align No. 5 cam with previously establish- ed top stop mark by rotating cam adjusting knob. Maintain No. 5 cam alignment by holding adjusting knob. Rotate No. 3 cam so that indicator groove lines up with the fiber cam follower on LS3 breaker point. Refer to Figure 4. This alignment must be done with the crankshaft at top ...

  • Eaton TRS 3064 - page 10

    ...

  • Eaton TRS 3064 - page 11

    Item No. - 6. 20. 22. 23. 24. 25. 26. 27. 28. 28A 29. 30. 31. 32. 33. 33A 34 38. 40. 41. 42. 45. 46. 47. Part No. Description 302276 159 x 41 139 x 12 See table C See table C 201854 See table C 201869 See table C 306030 203003 61 x 22 412230 409346 See table C See table C 119 x 23 507137 153 x 530 203107 404583 411367 405330 203351 Shaft Bearing Sn ...

  • Eaton TRS 3064 - page 12

    FOOT MOUNTED CAM LIMIT SWITCH Part No. for Optional Cam No. 3 (Item No. 28A), is as follows: 203002 (For clockwise and clockwise 30” dwell) 203087 (for c’clockwise and c’clockwise 30” dwell) Eaton Corporation Airflex Division Cleveland, Ohio 44144 PWNTED IN u. 5. A. ...

  • Eaton TRS 3064 - page 13

    PDF form at Form ML-31 8 Revised September 3, 1997 Eaton Cor poration Airflex Division 9919 Clinton Road Cleveland, Ohio 44144 Printed in U.S.A. EAT ON PROD UCT WARR ANTY Subject to t he c ondit io ns st ated herei n, Eaton C orpo rati on w arran ts to the Pur chaser that e ach ne w Air fl ex Produ ct manufa ctured by Eaton will be free from fai lu ...

メーカー Eaton カテゴリー Switch

Eaton TRS 3064のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- TRS 3064の取扱説明書
- Eatonの製品カード
- パンフレット
- またはEaton TRS 3064の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Eaton TRS 3064の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Eaton TRS 3064の取り付け説明書、サービスマニュアル、簡易説明書、またはEaton TRS 3064のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Eaton TRS 3064の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Eaton TRS 3064デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがEaton TRS 3064を使用するのを助ける技術的文書のことです。説明書は通常、全てのEaton TRS 3064ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Eatonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Eaton TRS 3064の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははEaton TRS 3064の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Eaton TRS 3064に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Eaton TRS 3064デバイスの基本機能を使うにあたってのヒント。 Eaton TRS 3064のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Eaton TRS 3064に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるEaton TRS 3064のメーカー/サービスへの連絡先に関する情報。

Eaton TRS 3064についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもEaton TRS 3064の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがEaton TRS 3064で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)