Bedienungsanleitung Directed Electronics PVM-4210

17 Seiten 0.15 mb
Download

Zur Seite of 17

Summary
  • Directed Electronics PVM-4210 - page 1

    DEI PVM-4210 DIRECTED ENERGY, INC. PVM-4210 ±950V Pulse Generator Module OPERATION MANUAL Directed Energy, Inc. 2401 Research Blvd., Ste. 108 Fort Collins, Colorado 80526 970/493-1901 FAX 970/493-1903 ...

  • Directed Electronics PVM-4210 - page 2

    DEI PVM-4210 ...

  • Directed Electronics PVM-4210 - page 3

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 1 Table Of Contents 1.0 Sa fety ...........................................................................................................3 2.0 Ov ervi ew .....................................................................................................3 3.0 S ...

  • Directed Electronics PVM-4210 - page 4

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 2 ********** WARNING ********** SAFE OPERATING PROCEDURES AND PROPER USE OF THE EQUIPMENT ARE THE RESPONSIBILITY OF THE USER OF THIS SYSTEM. Directed Energy, Inc (DEI) provides information on its products and associated hazards, but it assumes no responsibility fo ...

  • Directed Electronics PVM-4210 - page 5

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 3 1.0 Safety The high voltage/high current nature of this device dictates the use of caution when operating or servicing this equipment. OBSERVE ALL SAFETY PRECAUTIONS LISTED BELOW. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY. Precautions: 1. The Pulser should ...

  • Directed Electronics PVM-4210 - page 6

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 4 photomultiplier tubes. The exceptional pulse fidelity of the PVM-4210 will optimize the performance of any syst em in which it is used. The module provides two pulse output channels, controlled by a common control logic. When the control logi c receives a gate s ...

  • Directed Electronics PVM-4210 - page 7

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 5 +5V +15V Gate I nv ersi on on/off Pulse Generat ion Ov er current i nhibi t Prim ary Drive Trans former +75V Pow er Supply +9 50V Po wer Supply Positive Pul l Up Positive Pul l Down Neg ativ e Pul l Down Ov ercurrent Sen se Output Current Sens e +/- Neg ativ e P ...

  • Directed Electronics PVM-4210 - page 8

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 6 3.0 Specifications The pulser will meet or exceed the following specifications. All specifications are measured into a 50pF load connected to each of the two outputs with 12” (~30cm) of Belden 8218 (75 Ω) coaxial cable : OUTPUT PULSE ELECTRICA L CHARA CTERIS ...

  • Directed Electronics PVM-4210 - page 9

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 7 continuous pulse recurrence frequencies greater than 20KHz. This formula is not applicable when driving non-capacitive (resist ive or inductive) loads. Contact DEI for information or assistance in using the PVM-4210 with different load characteristics or impedan ...

  • Directed Electronics PVM-4210 - page 10

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 8 Output Pulse Configuration With Non-Inverted Gate Selected The ouput polarity can be reve rsed (so that the output is held at high voltage when the gate is low, and pulsed ground when the gate is high) by jumpering pins 10 and 11 together. This is shown in the f ...

  • Directed Electronics PVM-4210 - page 11

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 9 Output Pulse Configuration With Inverted Gate Selected 4.2 Power Supply Enable For safety and flexibility, the PVM-4210 features a power supply enable input (DSUB connector pin 14). In order to enable the DC power supplies (and therefore generate an output pul s ...

  • Directed Electronics PVM-4210 - page 12

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 10 5.0 OPERATING INSTRUCTIONS WARNING 1. Do not remove the input or output cabl es while the pulser is in operation. Never intentionally short-circuit the high voltage output of the pulser. Failure to observe these precautions can result in potential electric shoc ...

  • Directed Electronics PVM-4210 - page 13

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 11 2. Connect the input DSUB connector, and connect the output to an appropriate load, prior to applying +24VDC power. 3. Monitor the voltage across the load, utilizing an appropriate high voltage probe or attenuator. 4. Apply +24VDC to +28VDC power to the module, ...

  • Directed Electronics PVM-4210 - page 14

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 12 -Input trigger voltage too low. -Input trigger pulse width too short. Increase width. -Input trigger frequency too high. Reduce frequency. -No input high voltage. Check HV supplies. -Enable circuit not satisfied. Ensure that +5VDC is applied to DSUB pin 14. -No ...

  • Directed Electronics PVM-4210 - page 15

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 13 At DEI's discretion, DEI may elect to repair or replace the equipment claimed to be defective or refund the original purchase price, plus taxes and transportation charges incurred by the purchaser. This Warranty shall not apply to any product that has been ...

  • Directed Electronics PVM-4210 - page 16

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 14 APPENDIX Mechanical Dimensions And Mounting Hole/Connector Location Drawing ...

  • Directed Electronics PVM-4210 - page 17

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 15 11.50 5.80 TOP VIEW + HV ADJUST - HV ADJUST DB-15 PINOUT 2 GROUND 3 +5VDC @ 50mA OUTPUT 6 GATE (TTL into 50 O hms) 7 +24VDC RETURN (GROUND) 9 JUMPER TO PIN 10 FOR NON-INVERTING 10 GATE / OUTPUT POLARITY SELECT 11 JUMPER TO PIN 10 F OR INVERTING 12 GATE RETURN ( ...

Produzent Directed Electronics Kategorie Portable Generator

Dokumente, die wir vom Produzenten des Geräts Directed Electronics PVM-4210 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Directed Electronics
- Bedienungsanleitungen PVM-4210
- Produktkarten Directed Electronics
- Informationsbroschüren
- oder Energieetiketten Directed Electronics PVM-4210
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Directed Electronics PVM-4210.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Directed Electronics PVM-4210, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Directed Electronics PVM-4210. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Directed Electronics PVM-4210 ansehen.

Die komplette Bedienungsanleitung des Geräts Directed Electronics PVM-4210, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Directed Electronics PVM-4210 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Directed Electronics PVM-4210 verständlich ist.

Eine gänzliche Bedienungsanleitung von Directed Electronics sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Directed Electronics PVM-4210 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Directed Electronics PVM-4210 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Directed Electronics PVM-4210, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Directed Electronics PVM-4210 - die uns die ersten Schritte während der Nutzung von Directed Electronics PVM-4210 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Directed Electronics PVM-4210 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Directed Electronics PVM-4210 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Directed Electronics PVM-4210?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Directed Electronics PVM-4210 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Directed Electronics PVM-4210 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)