日本語 dropdown-ico

Directed Electronics PVM-4210の取扱説明書

17ページ 0.15 mb
ダウンロード

ページに移動 of 17

Summary
  • Directed Electronics PVM-4210 - page 1

    DEI PVM-4210 DIRECTED ENERGY, INC. PVM-4210 ±950V Pulse Generator Module OPERATION MANUAL Directed Energy, Inc. 2401 Research Blvd., Ste. 108 Fort Collins, Colorado 80526 970/493-1901 FAX 970/493-1903 ...

  • Directed Electronics PVM-4210 - page 2

    DEI PVM-4210 ...

  • Directed Electronics PVM-4210 - page 3

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 1 Table Of Contents 1.0 Sa fety ...........................................................................................................3 2.0 Ov ervi ew .....................................................................................................3 3.0 S ...

  • Directed Electronics PVM-4210 - page 4

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 2 ********** WARNING ********** SAFE OPERATING PROCEDURES AND PROPER USE OF THE EQUIPMENT ARE THE RESPONSIBILITY OF THE USER OF THIS SYSTEM. Directed Energy, Inc (DEI) provides information on its products and associated hazards, but it assumes no responsibility fo ...

  • Directed Electronics PVM-4210 - page 5

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 3 1.0 Safety The high voltage/high current nature of this device dictates the use of caution when operating or servicing this equipment. OBSERVE ALL SAFETY PRECAUTIONS LISTED BELOW. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY. Precautions: 1. The Pulser should ...

  • Directed Electronics PVM-4210 - page 6

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 4 photomultiplier tubes. The exceptional pulse fidelity of the PVM-4210 will optimize the performance of any syst em in which it is used. The module provides two pulse output channels, controlled by a common control logic. When the control logi c receives a gate s ...

  • Directed Electronics PVM-4210 - page 7

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 5 +5V +15V Gate I nv ersi on on/off Pulse Generat ion Ov er current i nhibi t Prim ary Drive Trans former +75V Pow er Supply +9 50V Po wer Supply Positive Pul l Up Positive Pul l Down Neg ativ e Pul l Down Ov ercurrent Sen se Output Current Sens e +/- Neg ativ e P ...

  • Directed Electronics PVM-4210 - page 8

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 6 3.0 Specifications The pulser will meet or exceed the following specifications. All specifications are measured into a 50pF load connected to each of the two outputs with 12” (~30cm) of Belden 8218 (75 Ω) coaxial cable : OUTPUT PULSE ELECTRICA L CHARA CTERIS ...

  • Directed Electronics PVM-4210 - page 9

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 7 continuous pulse recurrence frequencies greater than 20KHz. This formula is not applicable when driving non-capacitive (resist ive or inductive) loads. Contact DEI for information or assistance in using the PVM-4210 with different load characteristics or impedan ...

  • Directed Electronics PVM-4210 - page 10

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 8 Output Pulse Configuration With Non-Inverted Gate Selected The ouput polarity can be reve rsed (so that the output is held at high voltage when the gate is low, and pulsed ground when the gate is high) by jumpering pins 10 and 11 together. This is shown in the f ...

  • Directed Electronics PVM-4210 - page 11

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 9 Output Pulse Configuration With Inverted Gate Selected 4.2 Power Supply Enable For safety and flexibility, the PVM-4210 features a power supply enable input (DSUB connector pin 14). In order to enable the DC power supplies (and therefore generate an output pul s ...

  • Directed Electronics PVM-4210 - page 12

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 10 5.0 OPERATING INSTRUCTIONS WARNING 1. Do not remove the input or output cabl es while the pulser is in operation. Never intentionally short-circuit the high voltage output of the pulser. Failure to observe these precautions can result in potential electric shoc ...

  • Directed Electronics PVM-4210 - page 13

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 11 2. Connect the input DSUB connector, and connect the output to an appropriate load, prior to applying +24VDC power. 3. Monitor the voltage across the load, utilizing an appropriate high voltage probe or attenuator. 4. Apply +24VDC to +28VDC power to the module, ...

  • Directed Electronics PVM-4210 - page 14

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 12 -Input trigger voltage too low. -Input trigger pulse width too short. Increase width. -Input trigger frequency too high. Reduce frequency. -No input high voltage. Check HV supplies. -Enable circuit not satisfied. Ensure that +5VDC is applied to DSUB pin 14. -No ...

  • Directed Electronics PVM-4210 - page 15

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 13 At DEI's discretion, DEI may elect to repair or replace the equipment claimed to be defective or refund the original purchase price, plus taxes and transportation charges incurred by the purchaser. This Warranty shall not apply to any product that has been ...

  • Directed Electronics PVM-4210 - page 16

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 14 APPENDIX Mechanical Dimensions And Mounting Hole/Connector Location Drawing ...

  • Directed Electronics PVM-4210 - page 17

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 15 11.50 5.80 TOP VIEW + HV ADJUST - HV ADJUST DB-15 PINOUT 2 GROUND 3 +5VDC @ 50mA OUTPUT 6 GATE (TTL into 50 O hms) 7 +24VDC RETURN (GROUND) 9 JUMPER TO PIN 10 FOR NON-INVERTING 10 GATE / OUTPUT POLARITY SELECT 11 JUMPER TO PIN 10 F OR INVERTING 12 GATE RETURN ( ...

メーカー Directed Electronics カテゴリー Portable Generator

Directed Electronics PVM-4210のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PVM-4210の取扱説明書
- Directed Electronicsの製品カード
- パンフレット
- またはDirected Electronics PVM-4210の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Directed Electronics PVM-4210の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Directed Electronics PVM-4210の取り付け説明書、サービスマニュアル、簡易説明書、またはDirected Electronics PVM-4210のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Directed Electronics PVM-4210の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Directed Electronics PVM-4210デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDirected Electronics PVM-4210を使用するのを助ける技術的文書のことです。説明書は通常、全てのDirected Electronics PVM-4210ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Directed Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Directed Electronics PVM-4210の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDirected Electronics PVM-4210の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Directed Electronics PVM-4210に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Directed Electronics PVM-4210デバイスの基本機能を使うにあたってのヒント。 Directed Electronics PVM-4210のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Directed Electronics PVM-4210に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDirected Electronics PVM-4210のメーカー/サービスへの連絡先に関する情報。

Directed Electronics PVM-4210についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもDirected Electronics PVM-4210の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDirected Electronics PVM-4210で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)