Français dropdown-ico

Manuel d’utilisation Directed Electronics PVM-4210

17 pages 0.15 mb
Télécharger

Aller à la page of 17

Summary
  • Directed Electronics PVM-4210 - page 1

    DEI PVM-4210 DIRECTED ENERGY, INC. PVM-4210 ±950V Pulse Generator Module OPERATION MANUAL Directed Energy, Inc. 2401 Research Blvd., Ste. 108 Fort Collins, Colorado 80526 970/493-1901 FAX 970/493-1903 ...

  • Directed Electronics PVM-4210 - page 2

    DEI PVM-4210 ...

  • Directed Electronics PVM-4210 - page 3

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 1 Table Of Contents 1.0 Sa fety ...........................................................................................................3 2.0 Ov ervi ew .....................................................................................................3 3.0 S ...

  • Directed Electronics PVM-4210 - page 4

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 2 ********** WARNING ********** SAFE OPERATING PROCEDURES AND PROPER USE OF THE EQUIPMENT ARE THE RESPONSIBILITY OF THE USER OF THIS SYSTEM. Directed Energy, Inc (DEI) provides information on its products and associated hazards, but it assumes no responsibility fo ...

  • Directed Electronics PVM-4210 - page 5

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 3 1.0 Safety The high voltage/high current nature of this device dictates the use of caution when operating or servicing this equipment. OBSERVE ALL SAFETY PRECAUTIONS LISTED BELOW. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY. Precautions: 1. The Pulser should ...

  • Directed Electronics PVM-4210 - page 6

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 4 photomultiplier tubes. The exceptional pulse fidelity of the PVM-4210 will optimize the performance of any syst em in which it is used. The module provides two pulse output channels, controlled by a common control logic. When the control logi c receives a gate s ...

  • Directed Electronics PVM-4210 - page 7

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 5 +5V +15V Gate I nv ersi on on/off Pulse Generat ion Ov er current i nhibi t Prim ary Drive Trans former +75V Pow er Supply +9 50V Po wer Supply Positive Pul l Up Positive Pul l Down Neg ativ e Pul l Down Ov ercurrent Sen se Output Current Sens e +/- Neg ativ e P ...

  • Directed Electronics PVM-4210 - page 8

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 6 3.0 Specifications The pulser will meet or exceed the following specifications. All specifications are measured into a 50pF load connected to each of the two outputs with 12” (~30cm) of Belden 8218 (75 Ω) coaxial cable : OUTPUT PULSE ELECTRICA L CHARA CTERIS ...

  • Directed Electronics PVM-4210 - page 9

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 7 continuous pulse recurrence frequencies greater than 20KHz. This formula is not applicable when driving non-capacitive (resist ive or inductive) loads. Contact DEI for information or assistance in using the PVM-4210 with different load characteristics or impedan ...

  • Directed Electronics PVM-4210 - page 10

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 8 Output Pulse Configuration With Non-Inverted Gate Selected The ouput polarity can be reve rsed (so that the output is held at high voltage when the gate is low, and pulsed ground when the gate is high) by jumpering pins 10 and 11 together. This is shown in the f ...

  • Directed Electronics PVM-4210 - page 11

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 9 Output Pulse Configuration With Inverted Gate Selected 4.2 Power Supply Enable For safety and flexibility, the PVM-4210 features a power supply enable input (DSUB connector pin 14). In order to enable the DC power supplies (and therefore generate an output pul s ...

  • Directed Electronics PVM-4210 - page 12

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 10 5.0 OPERATING INSTRUCTIONS WARNING 1. Do not remove the input or output cabl es while the pulser is in operation. Never intentionally short-circuit the high voltage output of the pulser. Failure to observe these precautions can result in potential electric shoc ...

  • Directed Electronics PVM-4210 - page 13

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 11 2. Connect the input DSUB connector, and connect the output to an appropriate load, prior to applying +24VDC power. 3. Monitor the voltage across the load, utilizing an appropriate high voltage probe or attenuator. 4. Apply +24VDC to +28VDC power to the module, ...

  • Directed Electronics PVM-4210 - page 14

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 12 -Input trigger voltage too low. -Input trigger pulse width too short. Increase width. -Input trigger frequency too high. Reduce frequency. -No input high voltage. Check HV supplies. -Enable circuit not satisfied. Ensure that +5VDC is applied to DSUB pin 14. -No ...

  • Directed Electronics PVM-4210 - page 15

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 13 At DEI's discretion, DEI may elect to repair or replace the equipment claimed to be defective or refund the original purchase price, plus taxes and transportation charges incurred by the purchaser. This Warranty shall not apply to any product that has been ...

  • Directed Electronics PVM-4210 - page 16

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 14 APPENDIX Mechanical Dimensions And Mounting Hole/Connector Location Drawing ...

  • Directed Electronics PVM-4210 - page 17

    DEI PVM-4210 Document Number 9100-0201 Rev 8  Directed Energy, Inc. 2000-2002 Page 15 11.50 5.80 TOP VIEW + HV ADJUST - HV ADJUST DB-15 PINOUT 2 GROUND 3 +5VDC @ 50mA OUTPUT 6 GATE (TTL into 50 O hms) 7 +24VDC RETURN (GROUND) 9 JUMPER TO PIN 10 FOR NON-INVERTING 10 GATE / OUTPUT POLARITY SELECT 11 JUMPER TO PIN 10 F OR INVERTING 12 GATE RETURN ( ...

Fabricant Directed Electronics Catégorie Portable Generator

Les documents que nous recevons du fabricant de l'appareilDirected Electronics PVM-4210 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Directed Electronics
- manuels d’utilisations PVM-4210
- fiches produit Directed Electronics
- dépliants
- ou étiquettes-énergie Directed Electronics PVM-4210
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Directed Electronics PVM-4210.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Directed Electronics PVM-4210, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Directed Electronics PVM-4210. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Directed Electronics PVM-4210.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Directed Electronics PVM-4210, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Directed Electronics PVM-4210 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Directed Electronics PVM-4210.

Le manuel d’utilisation complet Directed Electronics, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Directed Electronics PVM-4210 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Directed Electronics PVM-4210, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lDirected Electronics PVM-4210 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Directed Electronics PVM-4210 - qui devraient nous aider dans les premières étapes lors de l'utilisation Directed Electronics PVM-4210
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Directed Electronics PVM-4210
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Directed Electronics PVM-4210 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Directed Electronics PVM-4210?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Directed Electronics PVM-4210, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Directed Electronics PVM-4210 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)