Bedienungsanleitung Kreg PRS1020

18 Seiten 4.17 mb
Download

Zur Seite of 18

Summary
  • Kreg PRS1020 - page 1

    RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...

  • Kreg PRS1020 - page 2

    Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’ s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoi ...

  • Kreg PRS1020 - page 3

    Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...

  • Kreg PRS1020 - page 4

    1 Phenolic Insert Plate RT10101 1 2 T able T op RT10102 1 3 T-Miter Track RT10103 1 4 2” Reducing Ring RT10107 1 5 1-13/64” Reducing Ring RT10106 1 6 Brass Starting Pin RT10108 1 7 Support Strut RT10171 2 8 Insert Plate Leveler RT10100 4 9 1/4-20 x 3/4” Set Screw DK1522 1 10 1/4-20 x 1-1/2” Set Screw RT101 11 8 11 1-1/4 Coarse Screw SML-C12 ...

  • Kreg PRS1020 - page 5

    Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...

  • Kreg PRS1020 - page 6

    Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoid ...

  • Kreg PRS1020 - page 7

    RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...

  • Kreg PRS1020 - page 8

    Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...

  • Kreg PRS1020 - page 9

    Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...

  • Kreg PRS1020 - page 10

    Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...

  • Kreg PRS1020 - page 11

    Hardware # Description Part# Quantity 1 MOUNTING RAIL RT10124 1 2 CLAMP BLOCK ASSEMBL Y RT10125 1 3 FENCE MOUNT RT10126 1 4 LARGE FENCE RT10122 1 5 T ABLE MOUNT RT10123 1 6 FENCE FACE RT10128 2 7 FENCE END CAP RT10121 2 8 8” ALUMINUM T APE SLIDER RT10129 1 9 8” SCALE RT10139 1 10 PRECISION LENS CURSOR FT4063 1 11 FENCE GUARD RT10133 1 12 RIGHT ...

  • Kreg PRS1020 - page 12

    Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...

  • Kreg PRS1020 - page 13

    Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...

  • Kreg PRS1020 - page 14

    Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...

  • Kreg PRS1020 - page 15

    2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...

  • Kreg PRS1020 - page 16

    Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...

  • Kreg PRS1020 - page 17

    Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...

  • Kreg PRS1020 - page 18

    2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...

Produzent Kreg Kategorie Router

Dokumente, die wir vom Produzenten des Geräts Kreg PRS1020 erhalten, können wir in mehrere Gruppen teilen. Unteranderem in:
- technische Zeichnungen Kreg
- Bedienungsanleitungen PRS1020
- Produktkarten Kreg
- Informationsbroschüren
- oder Energieetiketten Kreg PRS1020
Jede von ihnen ist wichtig, jedoch finden wir die wichtigsten Informationen für den Nutzer des Geräts in der Bedienungsanleitung Kreg PRS1020.

Die Dokumentengruppe, die als Bedienungsanleitungen bezeichnet wird, wird ebenfalls in detaillierte Arten geteilt, solche wie: Montageanleitungen Kreg PRS1020, Wartungsanleitungen, Kurzanleitungen oder Benutzeranleitungen Kreg PRS1020. Abhängig vom Bedarf, sollten Sie das Dokument finden, das Sie brauchen. In unserem Service können Sie sich die populärste Bedienungsanleitung des Produkts Kreg PRS1020 ansehen.

Ähnliche Bedienungsanleitungen

Die komplette Bedienungsanleitung des Geräts Kreg PRS1020, wie sollte sie aussehen?
Die Bedienungsanleitung, auch bezeichnet als Benutzerhandbuch, oder einfach nur „Anleitung”, ist ein technisches Dokument, das dem Benutzer bei der Nutzung von Kreg PRS1020 hilfreich sein soll. Die Bedienungsanleitungen werden in der Regel von technischen Schriftstellern geschrieben, aber in einer Sprache, die für alle Nutzer von Kreg PRS1020 verständlich ist.

Eine gänzliche Bedienungsanleitung von Kreg sollte einige Grundelemente enthalten. Ein Teil von ihnen ist nicht so wichtig, wie z.B.: die Titelseite oder Autorenseiten. Die restlichen von ihnen jedoch, sollten Informationen liefern, die für den Nutzer von enormer Wichtigkeit sind.

1. Einführung und Hinweise, wie man sich in einer Bedienungsanleitung von Kreg PRS1020 bewegt - Am Anfang jeder Bedienungsanleitung sollten wir Hinweise bezüglich der Nutzungsart eines bestimmten Ratgebers finden. In ihr sollten sich Informationen über die Lokalisierung des Inhaltsverzeichnisses von Kreg PRS1020 befinden, FAQ oder über oft auftretende Probleme – also Stellen, die von den Benutzern in jeder Bedienungsanleitung am meisten gesucht werden
2. Inhaltsverzeichnis - Index aller Ratschläge bezüglich Kreg PRS1020, die wir im aktuellen Dokument finden
3. Ratschläge zur Nutzung der Grundfunktionen des Geräts Kreg PRS1020 - die uns die ersten Schritte während der Nutzung von Kreg PRS1020 erleichtern sollten
4. Troubleshooting - geordneter Tätigkeitslauf, der uns bei der Diagnose und als nächstes bei der Lösung wichtiger Probleme mit Kreg PRS1020 hilft
5. FAQ - häufig gestellte Fragen
6. Kontaktdaten Informationen darüber, wo man Kontakt zum Produzenten / Service von Kreg PRS1020 im bestimmten Land suchen kann, wenn es nicht gelingt, das Problem selbst zu lösen.

Haben Sie eine Frage bezüglich Kreg PRS1020?

Nutzen Sie das untere Formular

Wenn Sie mit Hilfe der gefundenen Bedienungsanleitung Ihr Problem mit Kreg PRS1020 nicht gelöst haben, stellen Sie eine Frage, indem Sie das untere Formular nutzen. Wenn einer der Nutzer ein ähnliches Problem mit Kreg PRS1020 hatte, ist es möglich, dass er mit Ihnen die Lösung teilen möchte.

Text vom Bild übertragen

Kommentare (0)