-
Kreg PRS1020 - page 1
RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...
-
Kreg PRS1020 - page 2
Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’ s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoi ...
-
Kreg PRS1020 - page 3
Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...
-
Kreg PRS1020 - page 4
1 Phenolic Insert Plate RT10101 1 2 T able T op RT10102 1 3 T-Miter Track RT10103 1 4 2” Reducing Ring RT10107 1 5 1-13/64” Reducing Ring RT10106 1 6 Brass Starting Pin RT10108 1 7 Support Strut RT10171 2 8 Insert Plate Leveler RT10100 4 9 1/4-20 x 3/4” Set Screw DK1522 1 10 1/4-20 x 1-1/2” Set Screw RT101 11 8 11 1-1/4 Coarse Screw SML-C12 ...
-
Kreg PRS1020 - page 5
Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...
-
Kreg PRS1020 - page 6
Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoid ...
-
Kreg PRS1020 - page 7
RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...
-
Kreg PRS1020 - page 8
Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...
-
Kreg PRS1020 - page 9
Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...
-
Kreg PRS1020 - page 10
Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...
-
Kreg PRS1020 - page 11
Hardware # Description Part# Quantity 1 MOUNTING RAIL RT10124 1 2 CLAMP BLOCK ASSEMBL Y RT10125 1 3 FENCE MOUNT RT10126 1 4 LARGE FENCE RT10122 1 5 T ABLE MOUNT RT10123 1 6 FENCE FACE RT10128 2 7 FENCE END CAP RT10121 2 8 8” ALUMINUM T APE SLIDER RT10129 1 9 8” SCALE RT10139 1 10 PRECISION LENS CURSOR FT4063 1 11 FENCE GUARD RT10133 1 12 RIGHT ...
-
Kreg PRS1020 - page 12
Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...
-
Kreg PRS1020 - page 13
Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...
-
Kreg PRS1020 - page 14
Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...
-
Kreg PRS1020 - page 15
2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...
-
Kreg PRS1020 - page 16
Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...
-
Kreg PRS1020 - page 17
Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...
-
Kreg PRS1020 - page 18
2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...
¿Tienes una pregunta acerca de Kreg PRS1020?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kreg PRS1020, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kreg PRS1020 probablemente compartirá una forma de solucionarlo.