Kreg PRS1020の取扱説明書

18ページ 4.17 mb
ダウンロード

ページに移動 of 18

Summary
  • Kreg PRS1020 - page 1

    RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...

  • Kreg PRS1020 - page 2

    Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’ s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoi ...

  • Kreg PRS1020 - page 3

    Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...

  • Kreg PRS1020 - page 4

    1 Phenolic Insert Plate RT10101 1 2 T able T op RT10102 1 3 T-Miter Track RT10103 1 4 2” Reducing Ring RT10107 1 5 1-13/64” Reducing Ring RT10106 1 6 Brass Starting Pin RT10108 1 7 Support Strut RT10171 2 8 Insert Plate Leveler RT10100 4 9 1/4-20 x 3/4” Set Screw DK1522 1 10 1/4-20 x 1-1/2” Set Screw RT101 11 8 11 1-1/4 Coarse Screw SML-C12 ...

  • Kreg PRS1020 - page 5

    Precision R outer T able T op Assembly Precision R outer T able T op Assembly Step 5: Mounting the router to the Insert Plate Step 6: Leveling the Insert Plate to the Opening Step 7: Installing & Leveling the Reducing Rings Step 8: Installing the Starting Pin Begin by locating the 3/8” phenolic Insert Plate (#1) and placing it face down on yo ...

  • Kreg PRS1020 - page 6

    Precision R outer T able T op Assembly T urn the Router T able top (#2) so it’s face down on the fl oor . Locate the two Support Struts (#7) and align them to the pre-drilled holes in the bottom of the Router T able T op. Mount the struts to the top using the eight ¾” Coarse Thread Screws (#16). Be careful not to over tighten. Note: T o avoid ...

  • Kreg PRS1020 - page 7

    RT1 01 16 V ersion 20070701 · Woodworking machines are dangerous, and can cause personal injury if not used properly . · Read safety instructions and operating instructions for your machine completely , before using products. Using this system before understanding its safe and proper use could result in serious injury to the operator . · Failure ...

  • Kreg PRS1020 - page 8

    Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...

  • Kreg PRS1020 - page 9

    Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...

  • Kreg PRS1020 - page 10

    Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...

  • Kreg PRS1020 - page 11

    Hardware # Description Part# Quantity 1 MOUNTING RAIL RT10124 1 2 CLAMP BLOCK ASSEMBL Y RT10125 1 3 FENCE MOUNT RT10126 1 4 LARGE FENCE RT10122 1 5 T ABLE MOUNT RT10123 1 6 FENCE FACE RT10128 2 7 FENCE END CAP RT10121 2 8 8” ALUMINUM T APE SLIDER RT10129 1 9 8” SCALE RT10139 1 10 PRECISION LENS CURSOR FT4063 1 11 FENCE GUARD RT10133 1 12 RIGHT ...

  • Kreg PRS1020 - page 12

    Precision R outer T able Fence Assembly Precision R outer T able Fence Assembly 2. 5. Locate the Mounting Rail (#1) and slide it over the ¾” Hex Bolts (#5) as shown. If you intend on using the Kreg Micro-Adjuster (sold separately), position the mounting rail so it’s fl ush with the front edge of the T able Mount. If you do not plan on using t ...

  • Kreg PRS1020 - page 13

    Safety Guidelines Step 13 Step 14 Step 15 Locate the 48” Center Reading T ape (#35) and trim each side to the 17-15/16” mark with a sturdy scissors. Carefully remove one corner of the backing, apply the tape 1/16 from the edge of the Large Fence and continue to remove the backing while you press the tape across the surface of the fence. Be care ...

  • Kreg PRS1020 - page 14

    Tools Required: • 7/16” Open Ended Wrench • Flat Head Screwdriver • Phillips Head Screwdriver Router T able Fence Precision ASSEMBL Y INSTRUCTIONS Item# PRS1 0 1 0 7. RT10142 V ersion 20070701 www.kregtool.com • 800.447.8638 When jointing, it’s always best to make light passes so you’ll probably use the 1/32-in. offset more frequently ...

  • Kreg PRS1020 - page 15

    2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...

  • Kreg PRS1020 - page 16

    Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...

  • Kreg PRS1020 - page 17

    Installing Height adjusters: In this step you will be adding the Height Adjusters to the bottom of each Leg. Place the Steel Stand face-down on your work surface so that all four legs are pointed up in the air , and are easily accessible, as shown in image A . Place the height adjuster into the base of the Leg, with the squared end at the bottom of ...

  • Kreg PRS1020 - page 18

    2 Universal Steel Stand Tools Required: • Square • 1/2” Socket wrench & extension • (2) 3/4” Open-end or adjustable wrenches • Phillips head driver bit Please call us at 800-447-8638 with any questions regarding the assembly of this stand. www.kregtool.com • 800.447.8638 Step 5 Joining T able Top to Stand: In this step you will be ...

メーカー Kreg カテゴリー Router

Kreg PRS1020のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PRS1020の取扱説明書
- Kregの製品カード
- パンフレット
- またはKreg PRS1020の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Kreg PRS1020の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Kreg PRS1020の取り付け説明書、サービスマニュアル、簡易説明書、またはKreg PRS1020のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Kreg PRS1020の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Kreg PRS1020デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKreg PRS1020を使用するのを助ける技術的文書のことです。説明書は通常、全てのKreg PRS1020ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Kregの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Kreg PRS1020の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKreg PRS1020の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Kreg PRS1020に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Kreg PRS1020デバイスの基本機能を使うにあたってのヒント。 Kreg PRS1020のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Kreg PRS1020に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKreg PRS1020のメーカー/サービスへの連絡先に関する情報。

Kreg PRS1020についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKreg PRS1020の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKreg PRS1020で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)