-
Waves MEQ-5 - page 1
Waves PuigTec MEQ-5 User Manual ...
-
Waves MEQ-5 - page 2
Waves PuigTec MEQ-5 User Manual 2 TABLE OF CONTENTS CHAPTER 1 – IN TROD UCTION ....................................................................................................... .................................... 3 1.1 W ELCOME ................................................................................................................. ...
-
Waves MEQ-5 - page 3
Waves PuigTec MEQ-5 User Manual 3 Chapter 1 – Introduction 1.1 Welcome Thank you for choosing Waves! In order to get the most out of your Waves processor, please take the time to read through this manual. In conjunction, we also suggest that you become familiar with www.wavesupport.net . There you will find an extensive Answer Base , the latest T ...
-
Waves MEQ-5 - page 4
1.2 Product Overview ABOUT PULTEC Custom-engineered and built by hand, the original Pultecs have long been a top choice of leadin g recording and mastering engineers. Pultecs are known for their ability to bring out individual frequency ranges without significantly altering other frequencies. In 1951, Gene Shenk and Ollie Summerland of Pulse Techni ...
-
Waves MEQ-5 - page 5
Waves PuigTec MEQ-5 User Manual 5 • Hum Waves modeled both 50Hz power current and 60Hz power current. If you listen closely, you will hear that there is a difference in hum level between 50Hz and 60Hz. Since hum is unique to each region and dependent upon the local electrical conditions, you may find that the modeled hum is different than the hum ...
-
Waves MEQ-5 - page 6
Below is a plot of the curve from the original Pultec MEQ-5, with all gains set to 0. Note the roll- off of -0.5dB at 20kHz. Waves PuigTec MEQ-5 User Manual 6 ...
-
Waves MEQ-5 - page 7
Waves PuigTec MEQ-5 User Manual 7 1.3 Components WaveShell technology enables us to split Waves processors into smaller plug-ins, which we call components . Having a choice of components for a particular processor gives you the flexibility to choose the configuration best suited to your material. The PuigTec MEQ5 has two component processors: • P ...
-
Waves MEQ-5 - page 8
Chapter 2 – Quickst art Guide • The LowMid Peak band offers 5 cutoff points and 10dB of Peak (boost). • The Mid Dip band offers 11 cutoff points and amount of 10dB Dip (attenuation). • The HiMid band offers 5 cutoff points and 10dB of Peak (boost). • Gain controls output level trimming. • The Output meter displays peak output level. Wav ...
-
Waves MEQ-5 - page 9
Chapter 3 – Interface and Controls 3.1 PuigTec MEQ-5 Interface 3.2 PuigTec MEQ-5 Controls LowMid Frequency Filter type Bell Cutoff points 200 Hz, 300 Hz, 500 Hz, 700 Hz, 1000 Hz Default 500 Hz LowMid Peak Range 0 to 11 (10dB boost in 0.1 steps) Default 0 Mid Frequency Filter type Bell Cutoff points 200 Hz, 300 Hz, 500 Hz, 700 Hz, 1000 Hz, 1.5 kHz ...
-
Waves MEQ-5 - page 10
Waves PuigTec MEQ-5 User Manual 10 Mid Dip Range 0 to 11 (10dB cut) Default 0 HiMid Frequency Filter type Bell Cutoff points 1.5 kHz, 2 kHz, 3 kHz, 4 kHz, 5 kHz Default 3kHz HiMid Peak Range 0 to 11 (10dB boost in 0.1 steps) Default 0 In turns the EQ on/off but leaves the analog modeling. Range On/Off Default On Mains controls analog characteristic ...
-
Waves MEQ-5 - page 11
Meters The PuigTecMEQ-5 meters display output level in dBFS. The LED located in the upper right corner lights up when output signal is clipping. Waves PuigTec MEQ-5 User Manual 11 ...
-
Waves MEQ-5 - page 12
Chapter 4 – The W aveSystem 4.1 The WaveSystem Toolbar All Waves processors feature the WaveSystem t oolbar which takes care of most administrative functions you will encounter while working with your Waves software. The features of the WaveSystem toolbar are the same on practically all Waves processors, so familiarity with its feature s will be ...
-
Waves MEQ-5 - page 13
Loading Presets and Setups Click-and-hold on the Load button to see the Load pop-up menu. The menu is divided into four sections. If a section is not currently available it will not appe ar in the Load pop-up menu. Open Preset File… Select to open any setup or preset file , whether from the Library or your own creations. ‘Filename.xps’: Displ ...
-
Waves MEQ-5 - page 14
Deleting Presets You may delete User Presets and presets within a Setup File. Factory Presets and Setup Library files cannot be deleted or overwritten. 1. Hold the Command (Mac)/Control (PC) key down. 2. Click-and-hold the Load button to see the pop-up menu. 3. While still holding the Command/Control key, select the preset or setup to delete. 4. A ...
-
Waves MEQ-5 - page 15
Waves PuigTec MEQ-5 User Manual 15 Value Window Buttons Value windows display the value of a control and allow click-and-drag adjustment, or direct control via the keyboard . • Using the mouse , click-and-drag on the value window to adjust. Some value windows support left/right, some up/down (as you hover over a button, arrows will appear to let ...
-
Waves MEQ-5 - page 16
Waves PuigTec MEQ-5 User Manual 16 TAB Functions TAB moves the ‘selected’ status to the next control, with shift-TAB moving in the reverse direction. Additionally, the Mac has an option-TAB function for ‘down’ movement and shift-option-TAB for ‘up’ movement where applicable. If you have several Value Window Buttons selected, TAB functio ...
¿Tienes una pregunta acerca de Waves MEQ-5?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Waves MEQ-5, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Waves MEQ-5 probablemente compartirá una forma de solucionarlo.