Español dropdown-ico

Manual de instrucciones KTI Networks KCD-302 Series

28 de páginas 1.62 mb
Descargar

Pasar a la página of 28

Summary
  • KTI Networks KCD-302 Series - page 1

    -1- INDUSTRIAL T ri-segment Medi a Converter KCD-302 Series Installation Guide DOC.060301-KCD-302 ...

  • KTI Networks KCD-302 Series - page 2

    -2- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from ...

  • KTI Networks KCD-302 Series - page 3

    -3- The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inte ...

  • KTI Networks KCD-302 Series - page 4

    -4- T a ble of Contents 1. Introduction ......................................................... 5 1.1 Features ........................................................................................ 7 1.2 Specifications ................................................................................ 8 1.3 Model Specifications ................... ...

  • KTI Networks KCD-302 Series - page 5

    -5- 1. Introduction The industrial tri-segment media converter series provides one 10/100BASE- TX Fast Ethernet port and two 100BASE-FX ports. It supports the connec- tions to three network segments, one UTP and two fiber cables. It serves the network data transfer between any two segments in switching basis. The following figure illustrates a basi ...

  • KTI Networks KCD-302 Series - page 6

    -6- For industrial environment, the converters are designed with the follow- ing enhanced features exceeding that of commercial media converters:  High a nd wide operating T emperature ra nge  W ide operating voltage ra nge for DC power input  Power input interface: Screw terminal block and DC jack for adapter  DIN rail mounting support ...

  • KTI Networks KCD-302 Series - page 7

    -7- 1.1 Features • Support network data transfer at full wire speed • The TP port supports 10Mbps and 100Mbps connections • Auto MDI/MDI-X detection function on the TP (copper) port • Auto-negotiation function on the TP port • Transparent conversion to 802.1Q VLAN tagged packets between any two segments • Far End Fault function on FX (f ...

  • KTI Networks KCD-302 Series - page 8

    -8- 1.2 Specifications This figure shows the important components of the converter: ...

  • KTI Networks KCD-302 Series - page 9

    -9- T wisted-Pair Interfa ce (TP Por t, or called copper Por t) Connector Shielded RJ-45 Pin Assignments Auto MDI/MDI-X detection Signal Compliance IEEE 802.3 10BASE-T , 802.3u 100BASE-TX Data Speed 10Mbps or 100Mbps Duplex Mode Half-duplex or Full-duplex Configuration Auto-negotiation capable and optional forced manual settings Ca ble T ypes 10Mbp ...

  • KTI Networks KCD-302 Series - page 10

    -10- Configuration Setting Switches (SW) NO. FUNCTION SETTINGS SW1 TP Port mode O FF Auto-negotiation (default) O N Forced mode SW2 TP Port Duplex O F F Full duplex (default) O N Half duplex SW3 TP Port Speed O FF 100Mbps (default) ON 10Mbps SW4 802.3x function O FF Enable (default) O N Disable SW5 FX1 port duplex O F F Full duplex mode (default) O ...

  • KTI Networks KCD-302 Series - page 11

    -11- DC Power Input Interface Screw-type terminal block (2 sets for power wire cascading) DC Jack ( -D 6.3mm / + D 2.0mm) Operating Input V oltages +7V ~ +30V(+5%) Power c on s um ption 2.7W max. @7.5VDC input 2.9W max. @24VDC input 3.0W max. @+30VDC input Basic Information MAC Addresses Entries 1 K Forwarding Throughput Full wire speed at 100M ful ...

  • KTI Networks KCD-302 Series - page 12

    -12- Certificate F C C Part 15 Class B CE/EMC EMI EN50081-1 Class B EMS EN55024 CE/L V D Safe ty E N 60950 EN 50081-1/1992 : EN55022:1994/A1:1995/A2:1997 CISPR Class B EN61000-3-2:2000 Device <75W EN61000-3-3:1995/A1:2001 Clause 5 EN 55024:1998/A1:2001 IEC 61000-4-2:1995 ESD T est IEC 61000-4-3:1995 RS T est IEC 61000-4-4:1995 EFT/BURST T est IE ...

  • KTI Networks KCD-302 Series - page 13

    -13- 1.3 Model Specifications The media converter series provides the following fiber options: KCD-302-xxx WaveL. Reference Operating Model Ext. FX Connectors (nm) Fiber Distance Te mperature -2T FX1 : ST MMF 1310 2 k m -10 ~ 70 o C FX2 : ST MMF 1310 2 km -10 ~ 70 o C -2C FX1 : SC MMF 1310 2 k m -10 ~ 70 o C FX2 : SC MMF 1310 2 k m -10 ~ 70 o C -2C ...

  • KTI Networks KCD-302 Series - page 14

    -14- 1.4 Special Functions Auto MDI/MDI-X Function This function allows the TP port to auto-detect the twisted-pair signals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically . Auto-negotiation Function When TP port is set on Auto-negotiation mode (SW1:ON), it is featured with auto-negotiation f ...

  • KTI Networks KCD-302 Series - page 15

    -15- 2. Installation 2.1 Unpacking Check that the following components have been included: • Information CD • The product unit • DIN-rail mounting bracket If any item is found missing or damaged, please contact your local reseller for replacement. The following are available optional accessories: • Panel Mounting Bracket The bracket is used ...

  • KTI Networks KCD-302 Series - page 16

    -16- 2.2 DIN-Rail Mounting In the product package, a DIN-rail bracket is provided for mounting the converter in a industrial DIN-rail enclosure. The steps to mount the device onto a DIN-rail are: 1. Clamp the bracket into the rear of the device. Align the bracket with the rear face of the device and screw it onto the device unit. ...

  • KTI Networks KCD-302 Series - page 17

    -17- 2. Unscrew and loose the mounting clamp plate of the bracket. Mount the bracket with the device onto the DIN rail. 5. Screw the clamp with the bracket and make sure the device is properly fixed on the DIN rail. ...

  • KTI Networks KCD-302 Series - page 18

    -18- M ake sure that there are proper heat dissi pation from a nd a dequate ven- tilation around the device. The final mechanical dimensions after installing DIN rail mounting bracket are: ...

  • KTI Networks KCD-302 Series - page 19

    -19- 2.3 Mounting on a Panel Surface An optional mounting bracket, as shown below is also available for mount- ing the device on a panel surface such as a wall, a wood board, or a metal plate in an industrial enclosure. T o mount the device on a pa nel surface, the ste ps are: 1. Clamp the bracket into the device and align the bracket with the bott ...

  • KTI Networks KCD-302 Series - page 20

    -20- 2. Mount a nd screw the device on the target surface. The final dimen- sion after bracket installation is also shown below: Make sure that there are proper heat dissipation from and adequate ven- tilation around the device. Do not place heavy objects on the device. ...

  • KTI Networks KCD-302 Series - page 21

    -21- 2.4 Applying Power The product provide two types of power interfaces, terminal block and DC power ja ck for receiving DC power input from external power supply . DC Power Input Specification Operating V oltage + 7 ~ +30VDC Power Consumption Max. 3.0W @30VDC DC Power T erminal Block Connectors Screw-type T erminal block (2 sets) Pin Assignments ...

  • KTI Networks KCD-302 Series - page 22

    -22- DC2 + a nd DC2 - ca n be installed with a nother power-pair f or delivering the main power input to next converter in a ca sca ding way . Note: Only up to four device units can be cascaded to receive power from one main power input source. DC Power Jack Connector: Jack D 6.3mm D 2.0mm AC Power Adapters: Optional commercial rated adapters are a ...

  • KTI Networks KCD-302 Series - page 23

    -23- 2.5 Making TP Port Connection TP port is featured to support connection to : • Auto-negotiation devices • Auto-negotiation incapable 10BASE-T devices • Auto-negotiation incapable 100BASE-TX devices Network Cables 10BASE-T : 2-pair UTP Cat. 3,4,5 , EIA/TIA-568B 100-ohm STP 100BASE-TX: 2-pair UTP Cat. 5, EIA/TIA-568B 100-ohm STP Link dista ...

  • KTI Networks KCD-302 Series - page 24

    -24- 2.6 Ma king FX Port Connection s FX1 port and FX2 port operate on 100Mbps and full duplex (factory default). A variety of fiber options is provided as listed in Section 1.3. Network Cables Multimode (MMF) - 50/125, 62.5/125 Single mode (SMF) - 9/125 ...

  • KTI Networks KCD-302 Series - page 25

    -25- 3 Configuration Switches & LED Indicators The following figure shows the locations of the configuration switches and LED indicators: Refer to the following sections for the related functions. ...

  • KTI Networks KCD-302 Series - page 26

    -26- 3.1 Configuration Switche s SW FUNCTION SETTING & ST A TE SW 1 TP Port mode OFF Auto-negotiation (default) O N Forced mode SW2 TP Port Duplex O FF Full duplex (default) O N Half duplex SW3 TP Port Speed OF F 100Mbps (default) O N 10Mbps SW 4 802.3x function OF F Enable (default) O N Disable SW 5 FX1 port duplex OF F Full duplex mode (defau ...

  • KTI Networks KCD-302 Series - page 27

    -27- 3.1.3 FX Port Duplex Settings SW5 SW6 This settings are used to set the duplex mode of the FX1 port and FX2 port individually . It is recommended to use full duplex mode f or FX con- nection unless its link partner is a fixed half duplex device. Half duplex mode will shorten the connection distance. The following table lists the maximum MMF ca ...

  • KTI Networks KCD-302 Series - page 28

    -28- 3.2 LED Indicators LED DISPLA Y ST A TUS & INTERPRET A TION PWR Power status ON Power on O F F Power off TP LINK TP port link status ON Link up and no traffic O F F Link fault Blink Rx/Tx activities 100M TP port speed status ON 100Mbps O F F 10Mbps F D X TP port duplex status ON Full duplex O F F Half duplex Blink Collisions on half duplex ...

Fabricante KTI Networks Categoría Network Card

Los documentos del dispositivo KTI Networks KCD-302 Series que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos KTI Networks
- manuales de instrucciones KCD-302 Series
- hojas de producto KTI Networks
- folletos informativos
- o etiquetas energéticas KTI Networks KCD-302 Series
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones KTI Networks KCD-302 Series.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje KTI Networks KCD-302 Series, instrucciones de servicio, instrucciones cortas o instrucciones de usuario KTI Networks KCD-302 Series. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto KTI Networks KCD-302 Series.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo KTI Networks KCD-302 Series, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar KTI Networks KCD-302 Series. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de KTI Networks KCD-302 Series.

El manual de instrucciones completo de KTI Networks debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual KTI Networks KCD-302 Series - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice KTI Networks KCD-302 Series, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de KTI Networks KCD-302 Series que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo KTI Networks KCD-302 Series - que deben facilitarnos los primeros pasos durante el uso de KTI Networks KCD-302 Series
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con KTI Networks KCD-302 Series
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de KTI Networks KCD-302 Series en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de KTI Networks KCD-302 Series?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con KTI Networks KCD-302 Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con KTI Networks KCD-302 Series probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)